Milwaukee Rotary Hammer Pull bit out as far, Chiseling and Chipping, Bushing Tools, Bull Points

Page 10

7.For core bits, once the maximum core bit depth is drilled, the core must be broken and removed.

•Install a chisel bit.

•Place the chisel into the hole kerf (Fig. 12).

•Chisel down into the kerf at several points until the core is loose or broken.

• Remove the core and vacuum/remove any remaining dust and de- bris.

•Install the core bit and continue the cut.

F i g .

NOTE: If unable to drill a hole in the kerf, pull back on the bit with the ham- mer running (Fig. 13). This will remove some of the dust and debris from the cut. Repeat this for every inch of drilling. If necessary, vacuum dust and debris from the cut and surrounding area.

Fig. 13	Pull bit out as far
	as possible once
	or twice per inch
	drilled.

Chiseling and Chipping

These MILWAUKEE Hammers may be used for chipping and chiseling.

When chiseling, hold the tool at an angle to the workpiece. Work from a corner or close to the edge of the workpiece, breaking off one small area at a time rather than attempting too large an area.

A variety of accessories are available.

Bushing Tools

Used to surface concrete.

Mortar Cutting Chisels (Seam Tools)

For removing old mortar for tuck pointing or caulking.

Bull Points

For demolition work and starting holes in concrete slabs.

Flat Chisels

For edging, chipping or channeling.

Scaling Chisels

For removing weld spatter or scale and cut- ting straight lines.

Slotting Chisel

For slotting and cutting between drilled holes in concrete and masonry.

page 10

Image 10

Contents Operators Manual Page Personal Safety Work Area Safety Power Tool USE and CareElectrical Safety ServiceFunctional Description Cat. NoGrounding Extension CordsAdjusting the Straight Side Handle Tool AssemblyAdjusting the Spade Side Handle Cat. No -20, 5339-20 only Installing Bits and ChiselsOperation Operator Force Using Rotary Percussion Core BitsCold Hammering If a hammer iron gets stuckDrill a hole through Work Drilling Large Diameter Holes with Core Bits FigCut approximately Deep with a core Bit Top viewBushing Tools Pull bit out as farChiseling and Chipping Mortar Cutting Chisels Seam ToolsAccessories MaintenanceFive Year Tool Limited Warranty Utilisation ET Entretien DE L’OUTIL Électrique Conserver CES Instructions Sécurité DU Lieu DE TravailSécurité Électrique Sécurité IndividuelleDescription Fonctionnelle No de catCordons DE Rallonge Calibres minimaux recommandés pour les Cordons de rallongeMise À LA Terre Avertissement Directives pour l’emploi des cordons de rallongeMontage DE Loutil Avertissement Installation des ciseaux pour marteauRéglage de la poignée latérale droite Maniement Martelage à froid Martelage unique Réglage du ciseau MentBlocage de la gâchette No de cat -20, 5339-20 uniquement Force de l’utilisateurMartelage avec rotation Martelage uniquementSi le marteau se coince Si la mèche se coincePerçage de gros trous avec des trépans carottiers Fig Percer un trou par ’ouvrageBoucharde Vue du hautCisellement et burinage Ciseau à mortierAccessoires Avertissement Maintenance AvertissementGarantie Limitée DE L’OUTIL DE Cinq ANS Seguridad Personal Guarde Estas Instrucciones Seguridad EN EL Área DE TrabajoSeguridad Eléctrica USO Y Cuidado DE LAS Herramientas EléctricasReglas Especificas DE Seguridad EspeciﬁcacionesDescripcion Funcional Extensiónes Eléctricas Tierra AdvertenciaGuías para el uso de cables de extensión Ensambaje DE LA Herramienta Advertencia Ajuste del mango lateral rectoOperacion Martillado en frío Arranque y parada de la herramientaTraba del gatillo Cat. No -20, 5339-20 únicamente Fuerza requerida del operadorExtraiga la broca de la herramienta Cinceles para cortar mortero Cincelado y corteMartelinas Cinceles con puntaAccesorios Advertencia Mantenimiento AdvertenciaGarantía Limitada DE Cinco Años Sawdust