Black & Decker D25550 Inserting and Removing Spline Drive, Accessories, Torque Limiting Clutch

Page 8
FIG. 5

582429-00/D25500 etc 1/29/03 9:29 AM Page 5

Leave the side handle mounting assembly in front position so that the depth adjustment rod can still be used.

2. Screw the side handle directly into one of the rear side handle positions on either side of the tool.

TO ADJUST THE DEPTH ROD

1.Insert bit into tool holder and loosen depth rod clamp nut.

2.Place drill bit onto a surface, adjust the rod to desired depth of hole. Using the depth rod will allow you to drill a hole the depth of the distance between the bit and the depth rod tip.

3.Tighten clamp nut.

NOTE: This adjustment can be made with or without side handle in place.

Inserting and Removing Spline Drive

3.Release the retaining pin button.

4.Pull on the bit to be sure that it is properly locked.

5.To remove a bit unlock the tool holder as described above.

Inserting and Removing SDS-max™ Accessories

FIG. 4: (D25500, D25600, D25830)

TURN OFF TOOL AND DISCONNECT FROM POWER SUPPLY.

1.Pull back the tool holder locking sleeve (A) and insert the bit shank.

2.Turn the bit slightly until the sleeve snaps back in position.

3.Pull on the bit to be sure that it is properly locked. The hammering function requires the bit to be able to move axially several centimeters when locked in the tool holder.

4.To remove bit, pull back the tool holder locking sleeve and pull the

bit out of the tool holder.

English

Accessories

FIG. 3: (D25550, D25551, D25650, D25850)

TURN OFF TOOL AND DISCONNECT FROM POWER SUPPLY.

1.Unlock the tool holder by pushing the retaining pin button (J) and holding it in.

2.Insert the bit shank into the tool holder as far as it will go.

FIG. 3

FIG. 4

Soft Start Feature (All Models)

The soft start feature allows you to build up speed slowly, thus preventing the drill bit from walking off the intended hole position when starting. The soft start feature also reduces the immediate torque reaction transmitted to the gearing and the operator if the hammer is started with the drill bit in an existing hole.

Torque Limiting Clutch

G

All rotary hammers are equipped with a torque limiting clutch that reduces the maximum torque reaction transmitted to the operator in the case of a jamming drill bit. This feature also prevents the gearing and motor from stalling. The torque limiting clutch has been factory set and cannot be adjusted.

Electronic Speed and Impact Control (Fig. 5)

The electronic speed and impact control allows the use of smaller drill

5

Page 7 Page 9
Image 8
Page 7 Page 9
Contents 582429-00/D25500 etc 1/29/03 929 AM Perceuses rotatives Rotomartillos English Important Safety Instructions Electrical SafetyPersonal Safety Work AreaTool USE and Care Additional Safety Instructions for Rotary HammersService Earthing terminal Save These Instructions for Future USE MotorSide Handle and Depth Rod To Mount in Front Position FIGInserting and Removing SDS-max Accessories AccessoriesSoft Start Feature All Models Inserting and Removing Spline DriveMode Selector Drilling with a Solid BITDrilling with a Core BIT Chipping and ChiselingRepairs Full WarrantyDAY no Risk Satisfaction Guarantee Importantes directives de sécurité Conserver CES DirectivesAire DE Travail Regles DE Sécurité Relatives À L’ÉLECTRICITÉSécurité Personnelle Utilisation DES Outils ET PrécautionsRéparation Installation EN Position Avant FIG Conserver LES Directives Pour Utilisation FutureMoteur Poignée latérale et tige de profondeurInstallation EN Position Arriere FIG Réglage DE LA Tige DE ProfondeurInstallation et dépose des accessoires SDS-max Commande électronique du régime et de l’impact figMise sous tension sans appel de courant tous les modèles Embrayage limiteur de coupleSélecteur de mode Témoin DEL D’ENTRETIEN ET D’ALIMENTATION D25600, D25650Perçage AU Moyen D’UN Foret Plein Perçage AU Moyen D’UN Foret CreuxAccessoires RéparationsGarantie complète Garantie Sans Risque DE 30 JoursInstrucciones de seguridad importantes Conserve Estas InstruccionesÁrea DE Trabajo Seguridad EléctricaUSO Y Cuidados DE LA Herramienta Lesiones Guarde Estas Instrucciones Para SU Futura Utilización Montaje EN LA Posición Delantera FIGFunción de arranque progresivo todos los modelos Inserción y desmontaje de accesorios estriadosInserción y desmontaje de accesorios SDS-max Embrague de limitación de Par Control electrónico de la Velocidad y el impacto figSelector de modo y Leds Indicadores DE Servicio Y DE Encendido D25600, D25650Garantía completa AccesoriosReparaciones Para Otras Localidades Llame AL 326
Top Page Image Contents