Festool PM571823, PI571823 Extension Cord, Settings, Electronics, Setting sanding motion Fig

Page 10

The switch [1-3]is an on/off switch (I = ON, 0 = OFF).

The circuit closer can only be actuated if the change-over switch [1-2]is in an en- gaged position.

In case of a power failure or if the mains connector is removed, move the on/off switch immediately to the Off position. This prevents uncontrolled restarting.

Extension Cord

If an extension cord is required, it must have sufficient cross-section to prevent an exces- sive drop in voltage or overheating. An ex- cessive drop in voltage reduces the output and can lead to failure of the motor. The table below shows you the correct cord diameter as a function of the cord length for this tool.

Total Extension

25

50

100

150

Cord Lenght (feet)

 

 

 

 

 

 

 

 

 

Cable size (AWG)

18

16

16

14

 

 

 

 

 

Use only U.L. and CSA listed extension cords.

Never use two extension cords together. In- stead, use one long one.

The lower the AWG number, the stronger the cord.

Settings

Consider the pictures on the fold-out page.

WARNING

Risk of injury, electric shock

XAlways pull the plug out of the socket be- fore performing any type of work on the machine!

Electronics

The machine features full-wave electronics with the following features:

Smooth start-up

The electronically controlled smooth start-up ensures that the machine starts up jolt-free.

Speed control

You can regulate the speed steplessly with the adjusting wheel [1-6]in the speed range (see Technical data). This enables you to op- timise the cutting speed to suit the surface (see table).

Constant speed

The preselected motor speed remains con- stant through electronic control to ensure a uniform cutting speed even when under load.

Temperature cut-out

The machine power supply is limited and the speed reduced if the motor exceeds a certain temperature. The machine continues operat-

ing at reduced power to allow the ventilator to cool the motor quickly. If the machine temperature exceeds the maximum permit- ted value for longer periods, the machine switches off completely after approx. 40 sec- onds and can only be switched on again once the motor has cooled sufficiently.

Setting sanding motion - Fig. [3]

+

The change-over switch [1-2]can be used to set three different sanding motions.

This change-over can only be carried out with the sanding pad stationary because the switch is locked during operation.

Coarse sanding, polishing - ROTEX rota- ry motion

The Rotex rotary motion is a combi- nation of rotary and eccentric mo- tions. This position is selected for sanding with high output (coarse sanding) and polishing.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Guide d’utilisation Guide d’utilisation Manual de instruccionesManual de instrucciones Page Page Page Page Technical data ContentsSymbols Safety instructions General safety instructionsPersonal Safety Electrical SafetyPower Tool USE and Care Service Machine-related safety instructionsBattery Tool USE and Care Metal processingIntended use Functional descriptionOperation Extension Cord SettingsSetting sanding motion Fig ElectronicsFine sanding eccentric motion Changing sanding/polishing padChanging sanding pad Fig Triangular sanding and pad change FigDelta sanding pad DSS-GE-STF-RO90 Attaching sanding accessoriesObserve the following instructions Slat sanding pad LSS-STF-RO90 FigEdge protector Fig Attaching polishing accessoriesDust extraction Working with the machineSanding pad brake Service and maintenanceAccessories SystainerFestool Limited Warranty WarrantyConditions of 1+2 Warranty DisposalTable a Coarse sanding Fine sanding Sanding Table B Polishing Sealing High-gloss polishingCaractéristiques techniques SymbolesSommaire Consignes de sécurité Consignes de sécurité dordre gé NéralSecurite Relative AU Systeme Electrique Place DE TravailSecurite DES Personnes Utilisation ET Emploi Soigneux DES Appareils Sans FIL Utilisation ET Emploi Soigneux DE Loutil ElectroportatifLa poussière, un risque Pour la santé Consignes de sécurité spécifiques La machineTravail sur métaux Description fonctionnelleUtilisation en conformité avec les instructions Mise en serviceRallonge électrique Régulation électronique RéglagesRéglage du mouvement de ponça Ge Fig Changement de patin de ponçage Changement de plateau de ponça Ge/polissage FigPonçage triangulaire et changement de plateau Fig Patin de ponçage Delta DSS-GE-STF RO90- Fig Observez les consignes suivantesPatin de ponçage pour lamelles LSS STF-RO90- Fig Protection pour chants Protec Tor Fig Fixation de laccessoire de polis SageAspiration Travail avec la machineAccessoires Entretien et maintenanceFrein de plateau Conditions de la garantie 1+2 ans RecyclageGarantie Garantie limitée de FestoolTableau B Polissage LIER, Sont Limitées À UNE Période DE Trois ANSTableau a Ponçage dégrossissant Ponçage fin Polissage miroirPores Plastique Datos técnicos ÍndiceSímbolos Lijadora excéntricaSeguridad Eléctrica Puesto DE TrabajoSeguridad DE Personas Trato Y USO Cuidadoso DE HERRA- Mientas Eléctricas Indicaciones de seguridad especí FicasServicio Riesgos para la salud producidos Por el polvo Tratamiento de metalesDescripción de las funciónes Alargador Uso conforme a lo previstoPuesta en servicio Tensión o frecuencia no permitida Peligro de caídaSistema electrónico AjustesRotex Cambiar el plato lijador y el plato Pulidor Fig Cambiar la zapata FigTenga en cuenta las siguientes adver- tencias Fijar los accesorios de lijadoFijación de los accesorios de pulido Zapata delta DSS-GE-STF-RO90- FigTrabajo con la máquina AspiraciónProtección de cantos Protector Peligro de lesionesFreno de plato Mantenimiento y cuidadoAccesorios Condiciones de la Garantía 1 + ReciclajeGarantía Garantía limitada de FestoolTabla a Lijado basto Lijado fino Tabla B Pulir Sellado Pulido abrillantador Page Page

PN571823, PAC571823, PM571823, PI571823 specifications

The Festool PI571823 series includes a selection of innovative power tools designed for professional craftsmen and DIY enthusiasts alike. This range encompasses the PM571823, PAC571823, and PN571823 models, each uniquely tailored to meet different needs while ensuring high performance, precision, and durability.

One of the flagship features of the PI571823 series is the advanced brushless motor technology. This innovation provides greater efficiency, longer tool life, and reduced maintenance compared to traditional brushed motors. The brushless motor offers consistent power and torque, enabling users to tackle a variety of tasks with ease, from intricate woodworking to demanding renovation projects.

The PM571823 model is particularly notable for its lightweight design, making it easy to handle and maneuver, especially in tight spaces. Equipped with an ergonomic grip, it minimizes user fatigue during prolonged use. Additionally, the integrated dust extraction system helps maintain a clean workspace and reduces health risks associated with inhaling fine particles.

The PAC571823 model comes with advanced electronic controls that allow for customizable speed settings. This feature enables users to adjust the tool’s performance based on specific applications, ensuring optimal results for various materials. The electronic speed control also aids in preventing tool overload, thus extending the lifespan of the equipment.

The PN571823 model stands out with its robust build quality and high-performance characteristics. It’s designed to withstand challenging environments, making it suitable for heavy-duty tasks. The model features a reliable safety system that prevents accidental starts, enhancing user safety, especially in a busy work environment.

All models in the PI571823 series are compatible with Festool’s extensive range of accessories and attachments, allowing users to expand functionality according to their specific needs. The tools also integrate seamlessly with Festool’s Systainer storage system, promoting organization and mobility in the workshop or job site.

In summary, the Festool PI571823 series, including the PM571823, PAC571823, and PN571823 models, delivers exceptional performance, innovative technologies, and user-oriented features. These tools are built to meet the demands of professional tradespeople while providing the reliability and precision that are the hallmarks of the Festool brand. Whether for woodworking, renovation or industrial applications, the PI571823 series is designed to enhance productivity and achieve outstanding results.
Top Page Image Contents