Ingersoll-Rand 4575759 user manual Membrane Keys

Page 31

Sensor I® Expert User Manual

6. Membrane Keys

Each membrane key has two functions. To access the lower function, simply press the key. The upper function can be accessed by holding in the Reset button and then press the membrane key.

xCp	When this key is pressed (with the Reset button held in), the Mean Value is displayed for
	approximately 1.5 seconds, then the Cp Value is displayed until the Reset button is
	released. Repeatedly pressing this key with the Reset button held in, will display Mean
	and Cp values for Torque or Angle.
Window	Press this key to display and edit the Torque and Angle high and low limits for a
	particular tightening mode. Press this key again to go back to the tightening mode.
s/Cpk	When this key is pressed (with the Reset button held in), the Standard Deviation is
	displayed for approximately 1.5 seconds, then the Cpk Value is displayed until the Reset
	button is released. Repeatedly pressing this key with the Reset button held in, will
	display Standard Deviation and Cpk values for Torque or Angle.
Display	Pressing this key changes the value that is being displayed on the screen. Each press
	toggles the display between Peak Torque (Pk), Angle (An), Ld (not used), and Dynamic
	Torque (Tq).
Units	Pressing this key will change the torque units displayed for the selected mode. All stored
	data will also be converted.
Clear	Pressing this button (while Reset is held in) clears custom tightening modes. This key
	also clears tightening data stored in memory.
Joint	This button changes the joint type for Yield Control tightening.
Store	Press this button (while Reset is held in) to store Curve Trace Data.

11

Image 31

Contents Sensor I Expert Electronic Wrenches Page Form 7266 Version 005, 08/04 Sensor I ExpertPage Page Page Wrench Reset To Dynamically Audit Residual Torque Dynamic Audit≤ 2d To Tighten to an Angle To Tighten to a TorqueTo Tighten to Yield Page Page Table of Contents Page Table of Contents Battery Charging Introduction ChapterPage Introduction Page Tool Description Page Tool Description Technical Data 125 250 400Page Expert 125, 250 and 400 Models Functions of ComponentsExpert Control System Status Lights Mode Selector Switch Digital Display Page Membrane Keys Audible Alarm Item no Longer in USE Page Operation Instructions Page General Information Wrench Operation InstructionsSetting Torque Units Torque Control Tightening Procedure Page Dynamic Audit Page Yield Control Page Angle Control Page Cycle Counter Resetting the Cycle CounterQuality Control Limits and Statistics Setup and Viewing Quality Control LimitsDeleting Quality Control Limits Use of Quality Control Limits Mean Standard Deviation Process Capability Index StatisticsCustom Tightening Modes Setup and Storage of Custom Tightening ModesIdentifying Custom Tightening Modes Retrieving Custom Tightening ModesClearing Custom Tightening Modes Data Storage and Retrieval Setup of Wrench for Data UploadLast two numerals are not shown on the wrench display Data Out During TighteningData Out at End of Tightening Parameter Dump End of Tightening Data Dump Tightening Curve Storage Tightening Curve Data Dump Torque Multiplier Function Setup of a Torque MultiplierPage Use of a Torque Multiplier Left Hand FastenersReset Adjustment EVS-models only Page Reset Adjustment Value Models 125, 250 Page Battery Charging Page Battery Charging Page Diagnostics Troubleshooting Page Introduction Diagnostics and TroubleshootingTorque Channel A/D Display Custom Mode #200 Angle Reference Arm Test Mode EA Models, Custom ModeBuzzer and LED Test Mode Custom Mode #209 Battery Level Test Mode Custom Mode #204EZ Angle Test Mode Custom Mode #207 Membrane Keypad Test Mode Custom Mode #208Time-out Adjustment Custom Mode #212 Software Version Number Test Custom Mode #211Page Calibration Page General Information CalibrationTorque Calibration Page EZ Angle Calibration EVS models Angle Reference Arm Calibration EA modelsPage Page Sample Data Reports Appendix aPage Sample Reports Parameter Dump Appendix aEnd of Tightening Data Dump Torque Torque Units Nm Tightening Curve Data DumpData Out During Tightening Data Out at End of TighteningPage Appendix B List Setup ModesPage Custom Modes Appendix BCustom Mode Appendix C Spare Parts ListPage Appendix C Spare Parts Listing ModelE40-STRP Spare Parts Listing Model 40E40-PR-LABEL Spare Parts Listing Model Spare Parts Listing Model 125 Spare Parts Listing Model Spare Parts Listing Model 250 Spare Parts Listing Model Spare Parts Listing Model 400 Page Appendix D Service CentersPage Appendix D Service CentersSensor I Expert Electronic Wrenches Save These INSTRUCTIONS. do not Destory Ingersoll-Rand Company