Ingersoll-Rand 4575759 user manual Data Storage and Retrieval, Setup of Wrench for Data Upload

Page 55

Sensor I® Expert User Manual

DATA STORAGE AND RETRIEVAL

The charger/data port (item 8 in Chapter 2: Tool Description) has an integral RS232 serial port. This an be connected to a PC, and with the InterLink software or a terminal program, the data can be uploaded to the computer. Examples of all outputs can be found in Appendix A. The communication parameters on the PC must be set as follows in order to transmit any data from the wrench.

Data Bits:	8
Stop Bit:	1
Parity:	None
Handshake:	None

The baud rate must match the current baud rate of the wrench. Valid baud rates can be 19200, 9600, 4800, 2400, 1200 & 600.

For use with the InterLink software, the wrench must be set to 2400. Instructions for use of this program are located in the CD jacket and the Help file of the software.

Setup of Wrench for Data Upload

1.Connect the serial cable from the charger/data port to the serial port of the computer.

2.Setup parameters in a computer terminal program.

3.Press the Reset button to turn on the wrench.

4.Move the Mode Selection switch to Setup.

5.With the Reset button held in, use the Parameter Adjustment Knob to select Custom Setup Mode #110 (the present baud rate will be shown, divided by 100 to fit on the display).

6.Move the Mode Selection switch to Torque Control.

33

Image 55

Contents Sensor I Expert Electronic Wrenches Page Form 7266 Version 005, 08/04 Sensor I ExpertPage Page Page Wrench Reset To Dynamically Audit Residual Torque Dynamic Audit≤ 2d To Tighten to an Angle To Tighten to a TorqueTo Tighten to Yield Page Page Table of Contents Page Table of Contents Battery Charging Introduction ChapterPage Introduction Page Tool Description Page Tool Description Technical Data 125 250 400Page Expert 125, 250 and 400 Models Functions of ComponentsExpert Control System Status Lights Mode Selector Switch Digital Display Page Membrane Keys Audible Alarm Item no Longer in USE Page Operation Instructions Page General Information Wrench Operation InstructionsSetting Torque Units Torque Control Tightening Procedure Page Dynamic Audit Page Yield Control Page Angle Control Page Cycle Counter Resetting the Cycle CounterQuality Control Limits and Statistics Setup and Viewing Quality Control LimitsDeleting Quality Control Limits Use of Quality Control Limits Mean Standard Deviation Process Capability Index StatisticsCustom Tightening Modes Setup and Storage of Custom Tightening ModesIdentifying Custom Tightening Modes Retrieving Custom Tightening ModesClearing Custom Tightening Modes Data Storage and Retrieval Setup of Wrench for Data UploadLast two numerals are not shown on the wrench display Data Out During TighteningData Out at End of Tightening Parameter Dump End of Tightening Data Dump Tightening Curve Storage Tightening Curve Data Dump Torque Multiplier Function Setup of a Torque MultiplierPage Use of a Torque Multiplier Left Hand FastenersReset Adjustment EVS-models only Page Reset Adjustment Value Models 125, 250 Page Battery Charging Page Battery Charging Page Diagnostics Troubleshooting Page Introduction Diagnostics and TroubleshootingTorque Channel A/D Display Custom Mode #200 Angle Reference Arm Test Mode EA Models, Custom ModeBuzzer and LED Test Mode Custom Mode #209 Battery Level Test Mode Custom Mode #204EZ Angle Test Mode Custom Mode #207 Membrane Keypad Test Mode Custom Mode #208Time-out Adjustment Custom Mode #212 Software Version Number Test Custom Mode #211Page Calibration Page General Information CalibrationTorque Calibration Page EZ Angle Calibration EVS models Angle Reference Arm Calibration EA modelsPage Page Sample Data Reports Appendix aPage Sample Reports Parameter Dump Appendix aEnd of Tightening Data Dump Torque Torque Units Nm Tightening Curve Data DumpData Out During Tightening Data Out at End of TighteningPage Appendix B List Setup ModesPage Custom Modes Appendix BCustom Mode Appendix C Spare Parts ListPage Appendix C Spare Parts Listing ModelE40-STRP Spare Parts Listing Model 40E40-PR-LABEL Spare Parts Listing Model Spare Parts Listing Model 125 Spare Parts Listing Model Spare Parts Listing Model 250 Spare Parts Listing Model Spare Parts Listing Model 400 Page Appendix D Service CentersPage Appendix D Service CentersSensor I Expert Electronic Wrenches Save These INSTRUCTIONS. do not Destory Ingersoll-Rand Company