Ingersoll-Rand 4575759 user manual End of Tightening Data Dump

Page 59

Sensor I® Expert User Manual

6.With the Reset button held in, use the Parameter Adjustment Knob to select the desired tightening mode. Select from:

A-	Angle Control
J-	Yield (joint) Control
b-	Dynamic Audit
t-	Torque Control
1 through 20-	Custom tightening modes 1-20

7.Release the Reset button once the tightening mode has been selected.

8.Press the Display button and the tightening parameters will be transmit- ted.

9.Move the Mode Selection switch to Setup.

10.Press the Reset button and adjust the Custom Setup Mode number below 20.

End of Tightening Data Dump

The Sensor I® Expert wrench stores end of tightening data for up to 1000 tightenings for each tightening mode. This final tightening data (Torque, Angle and optional External Channel) can be uploaded to a PC by completing the following:

1.Connect serial cable from the charger/data port to the serial port of the computer.

2.Press the Reset button to power up the wrench.

3.Move the Mode Selection switch to Setup.

4.With the Reset button held in, use the Parameter Adjustment Knob to select Custom Setup Mode #109. Note that an "A" appears on the main display.

37

Image 59

Contents Sensor I Expert Electronic Wrenches Page Form 7266 Version 005, 08/04 Sensor I ExpertPage Page Page Wrench Reset To Dynamically Audit Residual Torque Dynamic Audit≤ 2d To Tighten to Yield To Tighten to a TorqueTo Tighten to an Angle Page Page Table of Contents Page Table of Contents Battery Charging Introduction ChapterPage Introduction Page Tool Description Page Tool Description Technical Data 125 250 400Page Expert 125, 250 and 400 Models Functions of ComponentsExpert Control System Status Lights Mode Selector Switch Digital Display Page Membrane Keys Audible Alarm Item no Longer in USE Page Operation Instructions Page General Information Wrench Operation InstructionsSetting Torque Units Torque Control Tightening Procedure Page Dynamic Audit Page Yield Control Page Angle Control Page Cycle Counter Resetting the Cycle CounterQuality Control Limits and Statistics Setup and Viewing Quality Control LimitsDeleting Quality Control Limits Use of Quality Control Limits Mean Standard Deviation Process Capability Index StatisticsCustom Tightening Modes Setup and Storage of Custom Tightening ModesIdentifying Custom Tightening Modes Retrieving Custom Tightening ModesClearing Custom Tightening Modes Data Storage and Retrieval Setup of Wrench for Data UploadLast two numerals are not shown on the wrench display Data Out During TighteningData Out at End of Tightening Parameter Dump End of Tightening Data Dump Tightening Curve Storage Tightening Curve Data Dump Torque Multiplier Function Setup of a Torque MultiplierPage Use of a Torque Multiplier Left Hand FastenersReset Adjustment EVS-models only Page Reset Adjustment Value Models 125, 250 Page Battery Charging Page Battery Charging Page Diagnostics Troubleshooting Page Introduction Diagnostics and TroubleshootingTorque Channel A/D Display Custom Mode #200 Angle Reference Arm Test Mode EA Models, Custom ModeBuzzer and LED Test Mode Custom Mode #209 Battery Level Test Mode Custom Mode #204EZ Angle Test Mode Custom Mode #207 Membrane Keypad Test Mode Custom Mode #208Time-out Adjustment Custom Mode #212 Software Version Number Test Custom Mode #211Page Calibration Page General Information CalibrationTorque Calibration Page EZ Angle Calibration EVS models Angle Reference Arm Calibration EA modelsPage Page Sample Data Reports Appendix aPage Sample Reports Parameter Dump Appendix aEnd of Tightening Data Dump Torque Torque Units Nm Tightening Curve Data DumpData Out During Tightening Data Out at End of TighteningPage Appendix B List Setup ModesPage Custom Modes Appendix BCustom Mode Appendix C Spare Parts ListPage Appendix C Spare Parts Listing ModelE40-STRP Spare Parts Listing Model 40E40-PR-LABEL Spare Parts Listing Model Spare Parts Listing Model 125 Spare Parts Listing Model Spare Parts Listing Model 250 Spare Parts Listing Model Spare Parts Listing Model 400 Page Appendix D Service CentersPage Appendix D Service CentersSensor I Expert Electronic Wrenches Save These INSTRUCTIONS. do not Destory Ingersoll-Rand Company