Ingersoll-Rand 4575759 user manual Battery Level Test Mode Custom Mode #204

Page 76

Sensor I® Expert User Manual

at the low end is correct-the high end should follow. Model 40 should be returned to an authorized Ingersoll-RandService Center for adjustment.

Battery Level Test Mode (Custom Mode #204)

The display value will be between 100 (fully charged) and zero (depleted).

EZ Angle Test Mode (Custom Mode #207)

1.If Custom Setup Mode #103 has been set for CW ("rit") tightenings, the display should indicate a number between 95 and 105. Moving the wrench in the CW direction should cause the number to increase. Moving the wrench in the CCW direction should cause the number to decrease.

2.If custom Setup Mode #103 has been set for CCW tightenings ("-LEF"), the display should indicate a value between 795 and 805. Moving the wrench in the CW direction should cause the number to decrease.

Membrane Keypad Test Mode (Custom Mode #208)

Pressing any of the membrane keys should toggle an adjacent display legend on and off.

Head Position Test (Models EVS125-, EVS250- and EVS400-, Cus- tom Mode #208)

Index the head. Buzzer should sound when head is in either position off of the center.

Buzzer and LED Test Mode (Custom Mode #209)

The LED's should flash on and off. Pressing any of the membrane keys should cause the buzzer to sound.

Display/Serial Link Test Mode (Custom Mode #210)

1. All display segments should be lit except the "CYCLE" legend.

50

Image 76

Contents Sensor I Expert Electronic Wrenches Page Sensor I Expert Form 7266 Version 005, 08/04Page Page Page Wrench Reset Dynamic Audit To Dynamically Audit Residual Torque≤ 2d To Tighten to an Angle To Tighten to a TorqueTo Tighten to Yield Page Page Table of Contents Page Table of Contents Battery Charging Chapter IntroductionPage Introduction Page Tool Description Page Technical Data 125 250 400 Tool DescriptionPage Functions of Components Expert 125, 250 and 400 ModelsExpert Control System Status Lights Mode Selector Switch Digital Display Page Membrane Keys Audible Alarm Item no Longer in USE Page Operation Instructions Page Wrench Operation Instructions General InformationSetting Torque Units Torque Control Tightening Procedure Page Dynamic Audit Page Yield Control Page Angle Control Page Resetting the Cycle Counter Cycle CounterSetup and Viewing Quality Control Limits Quality Control Limits and StatisticsDeleting Quality Control Limits Use of Quality Control Limits Statistics Mean Standard Deviation Process Capability IndexSetup and Storage of Custom Tightening Modes Custom Tightening ModesRetrieving Custom Tightening Modes Identifying Custom Tightening ModesClearing Custom Tightening Modes Setup of Wrench for Data Upload Data Storage and RetrievalData Out During Tightening Last two numerals are not shown on the wrench displayData Out at End of Tightening Parameter Dump End of Tightening Data Dump Tightening Curve Storage Tightening Curve Data Dump Setup of a Torque Multiplier Torque Multiplier FunctionPage Left Hand Fasteners Use of a Torque MultiplierReset Adjustment EVS-models only Page Reset Adjustment Value Models 125, 250 Page Battery Charging Page Battery Charging Page Diagnostics Troubleshooting Page Diagnostics and Troubleshooting Torque Channel A/D Display Custom Mode #200Angle Reference Arm Test Mode EA Models, Custom Mode IntroductionBattery Level Test Mode Custom Mode #204 EZ Angle Test Mode Custom Mode #207Membrane Keypad Test Mode Custom Mode #208 Buzzer and LED Test Mode Custom Mode #209Software Version Number Test Custom Mode #211 Time-out Adjustment Custom Mode #212Page Calibration Page Calibration General InformationTorque Calibration Page Angle Reference Arm Calibration EA models EZ Angle Calibration EVS modelsPage Page Appendix a Sample Data ReportsPage Appendix a Sample Reports Parameter DumpEnd of Tightening Data Dump Torque Tightening Curve Data Dump Torque Units NmData Out at End of Tightening Data Out During TighteningPage List Setup Modes Appendix BPage Appendix B Custom ModesCustom Mode Spare Parts List Appendix CPage Spare Parts Listing Model Appendix CSpare Parts Listing Model 40 E40-STRPE40-PR-LABEL Spare Parts Listing Model Spare Parts Listing Model 125 Spare Parts Listing Model Spare Parts Listing Model 250 Spare Parts Listing Model Spare Parts Listing Model 400 Page Service Centers Appendix DPage Service Centers Appendix DSensor I Expert Electronic Wrenches Save These INSTRUCTIONS. do not Destory Ingersoll-Rand Company