Ingersoll-Rand 4575759 user manual

Page 63

Sensor I® Expert User Manual

If while in a primary or custom tightening mode, the MUL symbol is on but the user is unsure of the multiplier value, it can be checked by following the procedure described in steps 2 and 3.

To disable a multiplier in a primary mode, follow the step by step procedure to set the multiplier, but select 1.00 as the multiplier value.

1.Turn Mode Select switch to Setup mode.

2.Press and hold in the Reset button and rotate Parameter Adjustment Knob until Custom Setup Mode #104 is indicated in the top right hand corner of the display. Note the symbol "MUL" is indicated in the top cen- ter of the display and the main display shows "---".

3.Rotate the Mode Select switch to the tightening mode for which the mul- tiplier is to be enabled. This display should show 1.00.

4.While holding in the Reset button, press the Units key to step through the multiplier values above. Pressing the Joint key will reset the multi- plier value to 1.00.

5.To adjust the programmable value, begin with the display at "10.00" and ensure that the Reset button is released. Rotate the Parameter Adjust- ment Knob until the display shows the desired value. Increments are in 0.01 steps.

6.Rotate the Mode Select switch back to the setup position. The display now should show "---" with "MUL" indicated.

7.Holding in the Reset button, adjust the Custom Mode number below 20.

41

Image 63

Contents Sensor I Expert Electronic Wrenches Page Form 7266 Version 005, 08/04 Sensor I ExpertPage Page Page Wrench Reset To Dynamically Audit Residual Torque Dynamic Audit≤ 2d To Tighten to a Torque To Tighten to an AngleTo Tighten to Yield Page Page Table of Contents Page Table of Contents Battery Charging Introduction ChapterPage Introduction Page Tool Description Page Tool Description Technical Data 125 250 400Page Expert 125, 250 and 400 Models Functions of ComponentsExpert Control System Status Lights Mode Selector Switch Digital Display Page Membrane Keys Audible Alarm Item no Longer in USE Page Operation Instructions Page General Information Wrench Operation InstructionsSetting Torque Units Torque Control Tightening Procedure Page Dynamic Audit Page Yield Control Page Angle Control Page Cycle Counter Resetting the Cycle CounterQuality Control Limits and Statistics Setup and Viewing Quality Control LimitsDeleting Quality Control Limits Use of Quality Control Limits Mean Standard Deviation Process Capability Index StatisticsCustom Tightening Modes Setup and Storage of Custom Tightening ModesIdentifying Custom Tightening Modes Retrieving Custom Tightening ModesClearing Custom Tightening Modes Data Storage and Retrieval Setup of Wrench for Data UploadLast two numerals are not shown on the wrench display Data Out During TighteningData Out at End of Tightening Parameter Dump End of Tightening Data Dump Tightening Curve Storage Tightening Curve Data Dump Torque Multiplier Function Setup of a Torque MultiplierPage Use of a Torque Multiplier Left Hand FastenersReset Adjustment EVS-models only Page Reset Adjustment Value Models 125, 250 Page Battery Charging Page Battery Charging Page Diagnostics Troubleshooting Page Introduction Diagnostics and TroubleshootingTorque Channel A/D Display Custom Mode #200 Angle Reference Arm Test Mode EA Models, Custom ModeBuzzer and LED Test Mode Custom Mode #209 Battery Level Test Mode Custom Mode #204EZ Angle Test Mode Custom Mode #207 Membrane Keypad Test Mode Custom Mode #208Time-out Adjustment Custom Mode #212 Software Version Number Test Custom Mode #211Page Calibration Page General Information CalibrationTorque Calibration Page EZ Angle Calibration EVS models Angle Reference Arm Calibration EA modelsPage Page Sample Data Reports Appendix aPage Sample Reports Parameter Dump Appendix aEnd of Tightening Data Dump Torque Torque Units Nm Tightening Curve Data DumpData Out During Tightening Data Out at End of TighteningPage Appendix B List Setup ModesPage Custom Modes Appendix BCustom Mode Appendix C Spare Parts ListPage Appendix C Spare Parts Listing ModelE40-STRP Spare Parts Listing Model 40E40-PR-LABEL Spare Parts Listing Model Spare Parts Listing Model 125 Spare Parts Listing Model Spare Parts Listing Model 250 Spare Parts Listing Model Spare Parts Listing Model 400 Page Appendix D Service CentersPage Appendix D Service CentersSensor I Expert Electronic Wrenches Save These INSTRUCTIONS. do not Destory Ingersoll-Rand Company