Black & Decker LDX220SBR instruction manual Safety Warnings and Instructions Drills

Page 8

c. Move charger and battery pack to a location where the surrounding air temperature is approximately 65°F - 75°F (18°- 24°C).

d. If charging problems persist, take the tool, battery pack and charger to your local service center.

4. The battery pack should be recharged when it fails to produce sufficient power on jobs which were easily done previously. DO NOT CONTINUE to use under these conditions. Follow the charging procedure. You may also charge a partially used pack whenever you desire with no adverse affect on the battery pack.

5. Foreign materials of a conductive nature such as, but not limited to, steel wool, aluminum foil, or any buildup of metallic particles should be kept away from charger cavities. Always unplug the charger from the power supply when there is no battery pack in the cavity. Unplug charger before attempting to clean.

6. Do not freeze or immerse charger in water or any other liquid.

Shock hazard. Do not allow any liquid to get inside charger. Never

attemptWARNING:to open the battery pack for any reason. If the plastic housing of the battery pack breaks or cracks, return to a service center for recycling.

SAFETY WARNINGS AND INSTRUCTIONS: DRILLS

1. Hold drill firmly with one hand on the grip and the other hand on the bottom of the battery pack.

2. When attaching accessories in the drill chuck, hand tighten the keyless chuck firmly. Drill may stall (if overloaded or improperly used) causing a twist. Always

expectWARNING:the stall. Grip the drill firmly with both hands to control the twisting action and prevent loss of control which could cause personal injury. If a stall does occur, release the trigger immediately and determine the reason for the stall before re-starting.

INSTALLING AND REMOVING THE BATTERY PACK FROM THE TOOL

Make certain the lock-off button is engaged to prevent switch actuation beforeWARNING:removing or installing battery.

TO INSTALL BATTERY PACK: Insert battery pack into B tool until an audible click is heard (figure B). Make

sure battery pack is fully seated and fully latched into

position.

TO REMOVE BATTERY PACK: Depress the battery	C
release button as shown in figure C and pull battery	C
pack out of tool.

8

Image 8

Contents 20V MAX* Cordless Drill General Power Tool Safety Warnings Work area safetyPage Volts Hertz Watts Ansi Z87.1 eye protection CAN/CSA Z94.3Amperes Damage to electric plug and cord Minimum wire sizeElectric shock or electrocution Total Length of Cord SummerRecycling Pattern indicated on the labelSafety Warnings and Instructions Drills Installing and Removing the Battery Pack from the ToolTrigger Switch & Reversing Button Figure D Before installing or removing accessoriesTorque Control Figure E Keyless Chuck Figure FDual Range Gearing Figure G Screw DrivingOn Board BIT Storage Figure H DrillingDrilling in Masonry MaintenanceDrilling in Metal Service Information Full TWO-YEAR Home USE Warranty Mode DʼEMPLOI DE LA Perceuse Sans FIL DE 16V MAX*, 20V MAX Page Deélectriquelʼoutil électrique ContrôlerIns médicaux Le liquide qui gicle Utilisation sécuritaire de lʼoutil électriqueExposition au bruit peut entraîner une perte auditive Peut entraîner des blessures corporellesAmpères Tours à la minuteGuirlande. Cela permet de réduire le risque Dʼendommager la fiche ou le cordondʼalimentationOu une électrocution D. un dessus de table ou dʼétabli Remplacer immédiatementRisques de choc électrique, dʼélectrocution ou dʼincendie Manuels fournis avec lʼoutil avant dʼutiliser le chargeurConsignes de chargement décrites Sont dégagées lorsque les blocs-piles sont incinérésRecommandations EN Matière DE Rangement Fonctions DE Diagnostic DU ChargeurProcédure DE Charge Pile EN Mauvais ÉtatNe jamais ouvrir le bloc-piles pour Insertion ET Retrait DU BLOC-PILES DE LʼOUTILInsertion DU BLOC-PILES Insérer le bloc-piles Retrait DU BLOC-PILES Enfoncer le bouton deMandrin Sans CLÉ Figure F Détente ET Bouton Inverseur Figure DRéglage DU Couple Figure E Vissage Rangement Intégré DES Mèches Figure HPerçage Perçage DU BoisPerçage DE LA Maçonnerie DépannageInformation SUR LES Réparations Manual DE Instrucciones DEL Taladro Inalámbrico DE 20V MÁX Pautas DE SEGURIDAD/DEFINICIONES Mantenimiento adecuado.Las herramientas de Uso y mantenimiento de la herramienta con bateríasQuemadurasterminal al otroo incendio Garantizará la seguridad de la herramienta eléctricaPuede ocasionar la pérdida de la audición Control podría ocasionar lesiones personalesTerminales de conexión a tierre Símbolo de alertaElectrocución Riesgo de descarga eléctrica, electrocución o incendioProcedimiento DE Carga Cargue los paquetes de baterías sólo con cargadoresdeRecomendaciones CON Respecto AL Almacenamiento Diagnóstico DEL Cargador Batería EN MAL EstadoRetraso POR Paquete CALIENTE/FRÍO Dejar LA Batería EN EL CargadorInterruptor Disparador Y Botón DE Inversión Figura D Para Instalar EL Paquete DE BateríasPara Extraer EL Paquete DE Baterías Ajuste DEL Control DE Torsión Figura E Portabrocas SIN Llave Figura FAdvertencia Asegúrese de que el botón AccesoriosDestornillado Espacio EN LA Herramienta Para Guardar Brocas Figura HTaladrado Taladrado EN MaderaDetección DE Problemas AccesoriosPage Años DE Garantia Esta Garantia no Aplica CuandoSolamente Para Propositos DE Mexico