Sierra S5832SG installation instructions Installation Instructions

Page 1

Model S5832SG Control Panel 8 to 32 Zones

Installation Instructions

Downloaded from: http://www.guardianalarms.net

Page 1 Page 2
Image 1
Page 1 Page 2
Contents Installation Instructions Page Table of Contents AH Requirements for Backup Sierra Accessory LoadingCountry Specific Compliance Information SingaporeIntroduction Panel Setup and InstallationMounting the Panel Earth GroundWiring Knock-outs Top AH Requirements for Backup Backup BatterySierra Accessory Loading AC PowerKeypad Wiring Keypad WiringSierra Accessory Wiring Distances Output TerminalsZone Terminals AccessoriesOn-Board Relay Terminals TB2 S5050 Relay/Event Memory ModuleS5058 Zone Expansion Module SN990/991 SpreadNet Keypad/Remote SN915-BUS SpreadNet ReceiverSN961 SpreadNet Keyfob Digital Communicator ConnectionsRemote Programming RPS Programming the PanelTerminal Connections Programming With an LED Keypad Press Home to activate the RPS featureValue Zone LEDs Cmd Loc Data ValueMenu Programming Mode Quick Programming ModeProgramming With an Alpha Keypad Programming With an Icon KeypadInstaller Walk-Test Installer Mode Options, BlockEvent Memory Entry Delay Test Bypass 0 Home CancelExit Delay Test Battery TestBlock 1 Code Option Programming Block 2 Zone Configuration Programming Zone Bypass Enable Zones Chime Enable ZonesZone Response Time Zones 1 Audible Cadence Zones 1Block 3 Armed System Programming Home Arm Exit Delay Enable Quick Bypass Enable Comments4X Exit Delay Extension Enable Comments Options Low Battery Arming Comments OptionsAuto-Disarming Enable Area Comments Auto-Arming Enable AreaAuto-Disarming Enable Day of Week Swinger Alarm Lockout Limit CommentsStrobe/Siren Disable with Low Battery Comments Options Sounder Turn-On Delay Following Alarm Seconds CommentsSoak Mode Learning Period Duration Days Duress Active Only When Area ArmedExternal Bell Reverse Enable Comments Options Keypad Tamper Switch Enable By Address Keypad #Sounder Bell Test Enable By Area Comments Home Arming Enable Comments OptionsBlock 4 Digital Communicator Programming Account #4 Account #3Account #5 Account #6Keypad RPS Enable Comments RPS Callback Enable CommentsAlarm Dialing Delay Seconds Comments Hour Zone Dial Delay Comments OptionsInstaller Programming Report Routing Comments Power Supply Report RoutingSpreadNet Transmitter Low Battery Report Routing Comments Keypad and Accessory Tamper Report Routing CommentsBlock 5 Reporting Digits Programming Report Code, Zone Bypass Zones 1 Comments Report Code, Restoral Zones 1Report Code, Trouble Zones 1 Comments Report Code, Tamper Zones 1Report Code, AC Power Loss Report Code, Cancel Users 1 User #Report Code, AC Power Restoral Report Code, Low BatteryReport Code, Installer Programming Complete Report Code, Installer Programming StartReport Code, Ground Fault Report Code, Ground Fault RestoralReport Code, SpreadNet Keypad/Keyfob Low Battery Restoral Report Code, SpreadNet Keypad/Keyfob Low BatteryReport Code, Accessory Tamper Report Code, Accessory Tamper RestoralBlock 6 Real Time Clock Programming Block 7 Auxiliary Devices Programming Timer Units On Board Relay Exit Delay TerminatorTimer Count On Board Relay Timer Units Remm #1, Relay #1Timer Count Remm #2, Relay #1 Timer Units Remm #2, Relay #1Timer Units Remm #8, Relay #2 Timer Count Remm #2, Relay #2Timed Relay Closing Timer #1 Hours Timed Relay Closing Timer #1 Day of WeekTimed Relay Closing Timer #1 Minutes Timed Relay Closing Timer #2 Day of WeekBlock 9 Partition Area Programming Block 8 SpreadNet ProgrammingFirst to Open/Last to Close Enable Comments Options Area Access by User Number User # 1Keypad Assignments to Areas Keypads 1 Area Assignments SpreadNet Keypads 1Block 10 User Code Programming Area Access SN Keyfob/Remote # 1User Codes User # 1 User Codes User Codes Comments
Top Page Image Contents