Sierra S5832SG installation instructions Block 1 Code Option Programming

Programming Summary - Sierra Model S5832SG

Block 1 - Code Option Programming

This programming block is divided into 80 Command Locations (CL 001 - 080). This Block used to program the Installer’s Code (001-006), Default Installer Code on Power Up (007), Require Installer Code for Direct Connect via RPS (008), and to set up the User Code parameters. The parameters include setting Maid Code, Duress, and Kidwatch.

Installer Code

Cmd Loc	001	002	003	004	005	006
Default	0	1	2	3	4	5
Range	0 - 9	0 - 9	0 - 9	0 - 9	0 - 9	0 - 9

Comments

This is a 6-digit code which is required to allow access to installer program- ming mode. The code is programmed 1 digit per Cmd Loc.

Default Installer Code on Power Up? Comments Options:

Cmd Loc

Default

Range

007

2

1 - 2

If enabled (programmed as 2), this restores the Installer	1	No
Code to the default value (see CL 001 - 006) following a	2	Yes
power failure/restoral.

Installer Code Required on Direct Connect RPS?		Comments	Options:
Cmd Loc	008	If enabled, the Installer Code (CL 001 - 006) is required	1	No
Default	2	when programming the panel with the direct connect RPS	2	Yes
Range	1 - 2	function of COMMANDER II.

Maid Code Enable (by Area)									Comments	Options:
Cmd Loc	009	010	011	012	013	014	015	016	The Maid Code may be specified by active days of	0	Disabled
Default	0	0	0	0	0	0	0	0	the week and by individual areas. Area 1 may also	1	Saturday
Area	1	2	3	4	5	6	7	8	use keypad activation for temporary access.	2	Friday
Range	0 - 255 (CL 009)								NOTE: Maid Code Enable programming deter-	4	Thursday
	0 - 127 (CL 010 - 016)									8	Wednesday
									mines when the Maid Code may be used for disarm-	16	Tuesday
									ing the system. The Maid code is always available to	32	Monday
									arm the system.	64	Sunday
										128	By Keypad
Maid Code Hours, Temporary Access, Area 1									Comments

Cmd Loc

Default

Range

017

12

0 - 254

This option is used in conjunction with keypad activation of the Maid Code for area 1 only. Duration of the active period is from the time of activation by grand master user (user #1) or area master (user #12). To disable keypad (temporary) activation, program this location with 0.

Duress Code Enable (By Area)

Cmd Loc	018
Default	0
Range	0 - 255

Comments	Options:
If the system is divided into areas, this option deter-	0	Disabled
mines if the duress code associated with a specific	1	Area 1
area is active. Refer to the Sierra S5090 Reference	2	Area 2
Manual (P/N 5-051-528-01), Block 9 programming	4	Area 3
for details on assigning user codes to areas.	8	Area 4
	16	Area 5
	32	Area 6
	64	Area 7
	128	Area 8

Kidwatch Enable

Cmd Loc	019
Default	0
Range	0, 129 - 255

Comments	Options:
If used, this option must be enabled (program	0	Disabled
value > 128) and have the appropriate days of	1	Saturday
the week programmed. The Kidwatch timer is	2	Friday
programmed from Block 6, CL 006 - 009. The	4	Thursday
same start and end times are used for all days	8	Wednesday
when the Kidwatch feature is active.	16	Tuesday
NOTE: If enabled, the Kidwatch code must be	32	Monday
	64	Sunday
entered if Area 1 is armed during the Kidwatch
	128	Enable (Master)
window (see Block 6, CL 006 - 009).

Keypad Lockout Enable Comments Options:

Cmd Loc

Default

Range

020

1

1 - 3

If enabled, 10 consecutive keystrokes without pro-	1	Disabled
ducing a valid user code will cause a keypad	2	When Disarmed
delay starting at 15 seconds and doubling each	3	Always Active
time up to a maximum of 240 seconds (4 min).

13