Sierra S5832SG Auto-Arming Enable Area, Auto-Arming Time Hours, Auto-Arming Time Minutes

Page 22

Block 3 - Armed System Programming (cont.)

Auto-Arming Enable (Area)

Cmd Loc 022

Default 0

Range 0 - 255

Auto-Arming Time (Hours)

Cmd Loc 023

Default 0

Range 0 - 23

Auto-Arming Time (Minutes)

Cmd Loc

024

Default

0

Range

0 - 59

 

 

Comments

Auto-Arming may be enabled for any or all partitions. If enabled, the system will be automatically armed each day at the time specified in Block 3, CL 023 and 024. All partitions will auto-arm using the same timer.

When programming the time of day for auto-arming, use the 24-hour format. (Add 12 hours for afternoon and evening times.)

The internal sounder will sound a warning two min- utes and again at one minute prior to the Automatic Arming of the system.

Options:

0Disabled

1 Area 1

2 Area 2

4 Area 3

8 Area 4

16Area 5

32Area 6

64Area 7

128 Area 8

Auto-Disarming Enable (Area)

Comments

Cmd Loc

025

 

This will automatically disarm the partitions indicated

Default

0

 

according to the information programmed into Block

Range

0 - 255

 

3, CL 026 - 028. The value programmed is a total of all

 

 

 

areas to auto-disarm within the system.

 

 

 

Options:

0Disabled

1 Area 1

2 Area 2

4 Area 3

8 Area 4

16Area 5

32Area 6

64Area 7

128 Area 8

Auto-Disarming Enable (Day of Week)

Cmd Loc 026

Default 0

Range 0 - 127

Auto-Disarming Time (Hours)

Cmd Loc 027

Default 0

Range 0 - 23

Auto-Disarming Time (Minutes)

Comments

Options:

This will automatically disarm the areas specified

0

Disabled

in Block 3, CL 025. Auto-disarm will occur on the

1

Saturday

days programmed (Block 3, CL 026) and at the

2

Friday

time specified (Block 3, CL 027 - 028). The value

4

Thursday

programmed in Block 3, CL 026 is the total of all

8

Wednesday

days to auto-disarm the system.

16

Tuesday

 

32

Monday

When programming the time of day for auto-dis-

64

Sunday

arming, use the 24-hour format. (Add 12 hours for

 

 

afternoon and evening times.)

 

 

Cmd Loc

028

Default

0

Range

0 - 59

Swinger Alarm Lockout Limit

Comments

Limits the number of alarm signals reported and/or annunciated during an

Cmd Loc

029

 

 

armed period. Additional alarms will not be indicated. Setting the limit to

Default

0

 

 

zero (0) indicates unlimited signals reported. In partitioned systems, this

Range

0 - 15

 

 

limit pertains to ALL partitions (areas).

 

 

 

Audible Output Limits

Comments

Options:

Cmd Loc

030

 

Determines the number of times the

1

Unlimited Local Audibles.

Default

2

 

sounders (bells) will indicate an alarm

2

One Audible per Zone.

Range

1 - 3

 

condition during an armed period.

3

One Audible per Area.

 

 

 

 

 

 

Fire Verification Enable

Comments

Options:

Cmd Loc

031

 

Determines if powered loop

1

No Verification

Default

1

 

(zone 8) or switched aux

2

Powered Loop Verify Only

Range

1 - 4

 

power will be reset for fire

3

Switched Aux Verify Only

 

 

 

alarm verification.

4

Powered Loop and Switched Aux

 

 

 

 

 

 

 

AC Power Loss Delay Before Report (Minutes)

Comments

 

 

Cmd Loc

Default

Range

032

15

1 - 255

Specifies the number of minutes AC power must be interrupted before an AC power fail report is sent.

Battery Test Interval (Hours)

Comments

Cmd Loc

Default

Range

033

24

0 - 24

The interval (in hours) between battery tests. If programmed for 0, the test is disabled. This test is conducted each time the system is reset. Additional tests follow the test interval specified.

18

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Installation Instructions Page Table of Contents Country Specific Compliance Information Sierra Accessory LoadingAH Requirements for Backup SingaporeMounting the Panel Panel Setup and InstallationIntroduction Earth GroundWiring Knock-outs Top Sierra Accessory Loading Backup BatteryAH Requirements for Backup AC PowerSierra Accessory Wiring Distances Keypad WiringKeypad Wiring Output TerminalsOn-Board Relay Terminals TB2 AccessoriesZone Terminals S5050 Relay/Event Memory ModuleS5058 Zone Expansion Module SN961 SpreadNet Keyfob SN915-BUS SpreadNet ReceiverSN990/991 SpreadNet Keypad/Remote Digital Communicator ConnectionsRemote Programming RPS Programming the PanelTerminal Connections Value Press Home to activate the RPS featureProgramming With an LED Keypad Zone LEDs Cmd Loc Data ValueProgramming With an Alpha Keypad Quick Programming ModeMenu Programming Mode Programming With an Icon KeypadInstaller Walk-Test Installer Mode Options, BlockEvent Memory Exit Delay Test Bypass 0 Home CancelEntry Delay Test Battery TestBlock 1 Code Option Programming Block 2 Zone Configuration Programming Zone Response Time Zones 1 Chime Enable ZonesZone Bypass Enable Zones Audible Cadence Zones 1Block 3 Armed System Programming 4X Exit Delay Extension Enable Comments Options Quick Bypass Enable CommentsHome Arm Exit Delay Enable Low Battery Arming Comments OptionsAuto-Disarming Enable Day of Week Auto-Arming Enable AreaAuto-Disarming Enable Area Comments Swinger Alarm Lockout Limit CommentsSoak Mode Learning Period Duration Days Sounder Turn-On Delay Following Alarm Seconds CommentsStrobe/Siren Disable with Low Battery Comments Options Duress Active Only When Area ArmedSounder Bell Test Enable By Area Comments Keypad Tamper Switch Enable By Address Keypad #External Bell Reverse Enable Comments Options Home Arming Enable Comments OptionsBlock 4 Digital Communicator Programming Account #5 Account #3Account #4 Account #6Alarm Dialing Delay Seconds Comments RPS Callback Enable CommentsKeypad RPS Enable Comments Hour Zone Dial Delay Comments OptionsSpreadNet Transmitter Low Battery Report Routing Comments Power Supply Report RoutingInstaller Programming Report Routing Comments Keypad and Accessory Tamper Report Routing CommentsBlock 5 Reporting Digits Programming Report Code, Trouble Zones 1 Comments Report Code, Restoral Zones 1Report Code, Zone Bypass Zones 1 Comments Report Code, Tamper Zones 1Report Code, AC Power Restoral Report Code, Cancel Users 1 User #Report Code, AC Power Loss Report Code, Low BatteryReport Code, Ground Fault Report Code, Installer Programming StartReport Code, Installer Programming Complete Report Code, Ground Fault RestoralReport Code, Accessory Tamper Report Code, SpreadNet Keypad/Keyfob Low BatteryReport Code, SpreadNet Keypad/Keyfob Low Battery Restoral Report Code, Accessory Tamper RestoralBlock 6 Real Time Clock Programming Block 7 Auxiliary Devices Programming Timer Count On Board Relay Exit Delay TerminatorTimer Units On Board Relay Timer Units Remm #1, Relay #1Timer Units Remm #8, Relay #2 Timer Units Remm #2, Relay #1Timer Count Remm #2, Relay #1 Timer Count Remm #2, Relay #2Timed Relay Closing Timer #1 Minutes Timed Relay Closing Timer #1 Day of WeekTimed Relay Closing Timer #1 Hours Timed Relay Closing Timer #2 Day of WeekBlock 8 SpreadNet Programming Block 9 Partition Area ProgrammingKeypad Assignments to Areas Keypads 1 Area Access by User Number User # 1First to Open/Last to Close Enable Comments Options Area Assignments SpreadNet Keypads 1Block 10 User Code Programming Area Access SN Keyfob/Remote # 1User Codes User # 1 User Codes User Codes Comments
Top Page Image Contents