Sierra S5832SG installation instructions Block 5 Reporting Digits Programming

Page 29

Block 4 - Digital Communicator Programming (cont.)

Keypad and Accessory Communications

Comments

Trouble Report Routing

Report routing for all communication trouble

 

 

 

and restoral reports associated with keypads

Cmd Loc

159

 

Default

2

 

and accessories connected to the system.

Range

1 - 5

 

 

Options:

1Disable Reports

2 Receiver 1 Only

3 Receiver 2 Only

4 Receivers 1 and 2

5 Receiver 1, with Receiver 2 as Back- up, Alternating

Audio Verification Enable (Listen-In)

Cmd Loc

160

Default

1

Range

1 - 4

Options:

1 No Audio Verification (AV)

2Trigger AV following alarm, but before releasing line. Panel may not seize line for 3 min. or send reports until AV session is complete.

3 Same as option #1, but allows reports to interrupt AV session.

4Same as option #1, except retriggers AV when panel attempts to seize line to send alarm report.

Digital Communications Enable

Cmd Loc 161

Default 1

Range 1 - 2

Comments

If disabled, programmed for No (1), the sys- tem will operate as a local system. Phone line checking will also be disabled. For reporting systems, program this location as Yes (2).

Options:

1No (Local System)

2 Yes

Telephone Line #1 Supervision Time (Minutes)

Cmd Loc

162

Default

5

Range

0 - 30

 

 

Telephone Line #2 Supervision Time (Minutes)

Cmd Loc 163

Default 5

Range 0 - 30

Comments

Amount of time (in minutes) that the phone line must be cut (open) before annunciation will occur and a report is sent to the central station. This is also the time interval required before the phone line cut action (Block 3, CL 036 and 037). Programming either command location with 0 will disable phone line checking for that line.

If the system is equipped with a single-line digital communicator, the pro- gramming of CL 163 will be ignored.

Test Report Phone Line Routing

Cmd Loc 164

Default 1

Range 1 - 3

Comments

This option allows the installer to select the phone line which will be used to send test reports. If a dual-line digital communicator is used, both lines may be se- lected for test reporting. The data programmed in this location overrides the programming of Block 4, CL 112 for test reports only.

Options:

1Line #1 Only

2 Line #2 Only

3 Line #1 and Line #2

Block 5 - Reporting Digits Programming

This Block has 180 Command Locations (CL 001 - 180). Certain reporting formats such as CFSK-IV, Contact ID, and SIA have pre-defined codes and the data programmed here is ignored. Reports may be disabled by programming the reporting code as 0 (or 00 for two-digit codes). Each Cmd Loc may be programmed with any value from 0 - 15.

Report Code, Alarm (Zones 1 - 32)

 

 

 

 

 

Cmd Loc

001 002

003 004

005 006

007 008

009 010

011 012

Default

0

1

0

1

0

1

0

1

0

1

0

1

 

Zone

 

1

2

 

3

 

 

4

 

5

 

6

 

Cmd Loc

013 014

015 016

017 018

019 020

021 022

023 024

Default

0

1

0

1

0

1

0

1

0

1

0

1

 

Zone

 

7

8

 

9

 

 

10

 

11

 

12

 

Cmd Loc

025 026

027 028

029 030

031 032

033 034

035 036

Default

0

1

0

1

0

1

0

1

0

1

0

1

 

Zone

 

13

14

 

15

 

 

16

 

17

 

18

 

Cmd Loc

037 038

039 040

041 042

043 044

045 046

047 048

 

Default

0

1

0

0

0

1

0

1

0

1

0

1

 

Zone

 

19

20

 

21

 

 

22

 

23

 

24

 

Cmd Loc

049 050

051 052

053 054

055 056

057 058

059 060

 

Default

0

1

0

1

0

1

0

1

0

1

0

1

 

Zone

 

25

26

 

27

 

 

28

 

29

 

30

 

Cmd Loc

061 062

063 064

 

 

 

 

 

 

 

 

 

Default

0

1

0

1

 

 

 

 

 

 

 

 

 

Zone

 

31

32

 

 

 

 

 

 

 

 

 

 

Range

0 - 15 (All CL)

 

 

 

 

 

 

 

 

 

Comments

These codes are used to indicate alarm conditions. Each report code is a two-digit code. Reports may be disabled by programming a value of 00 into the Cmd Loc. Each location may contain any digit from 0 - 15.

NOTE: The programmed digits 10 - 15 will be sent to the central station as their hexadecimal equivalent, as shown in the table below:

Reporting Digit Conversion:

Decimal Hexadecimal

10A

11B

12C

13D

14E

15F

25

Image 29
Contents Installation Instructions Page Table of Contents AH Requirements for Backup Sierra Accessory LoadingCountry Specific Compliance Information SingaporeIntroduction Panel Setup and InstallationMounting the Panel Earth GroundWiring Knock-outs Top AH Requirements for Backup Backup BatterySierra Accessory Loading AC PowerKeypad Wiring Keypad WiringSierra Accessory Wiring Distances Output TerminalsZone Terminals AccessoriesOn-Board Relay Terminals TB2 S5050 Relay/Event Memory ModuleS5058 Zone Expansion Module SN990/991 SpreadNet Keypad/Remote SN915-BUS SpreadNet ReceiverSN961 SpreadNet Keyfob Digital Communicator ConnectionsTerminal Connections Programming the PanelRemote Programming RPS Programming With an LED Keypad Press Home to activate the RPS featureValue Zone LEDs Cmd Loc Data ValueMenu Programming Mode Quick Programming ModeProgramming With an Alpha Keypad Programming With an Icon KeypadEvent Memory Installer Mode Options, BlockInstaller Walk-Test Entry Delay Test Bypass 0 Home CancelExit Delay Test Battery TestBlock 1 Code Option Programming Block 2 Zone Configuration Programming Zone Bypass Enable Zones Chime Enable ZonesZone Response Time Zones 1 Audible Cadence Zones 1Block 3 Armed System Programming Home Arm Exit Delay Enable Quick Bypass Enable Comments4X Exit Delay Extension Enable Comments Options Low Battery Arming Comments OptionsAuto-Disarming Enable Area Comments Auto-Arming Enable AreaAuto-Disarming Enable Day of Week Swinger Alarm Lockout Limit CommentsStrobe/Siren Disable with Low Battery Comments Options Sounder Turn-On Delay Following Alarm Seconds CommentsSoak Mode Learning Period Duration Days Duress Active Only When Area ArmedExternal Bell Reverse Enable Comments Options Keypad Tamper Switch Enable By Address Keypad #Sounder Bell Test Enable By Area Comments Home Arming Enable Comments OptionsBlock 4 Digital Communicator Programming Account #4 Account #3Account #5 Account #6Keypad RPS Enable Comments RPS Callback Enable CommentsAlarm Dialing Delay Seconds Comments Hour Zone Dial Delay Comments OptionsInstaller Programming Report Routing Comments Power Supply Report RoutingSpreadNet Transmitter Low Battery Report Routing Comments Keypad and Accessory Tamper Report Routing CommentsBlock 5 Reporting Digits Programming Report Code, Zone Bypass Zones 1 Comments Report Code, Restoral Zones 1Report Code, Trouble Zones 1 Comments Report Code, Tamper Zones 1Report Code, AC Power Loss Report Code, Cancel Users 1 User #Report Code, AC Power Restoral Report Code, Low BatteryReport Code, Installer Programming Complete Report Code, Installer Programming StartReport Code, Ground Fault Report Code, Ground Fault RestoralReport Code, SpreadNet Keypad/Keyfob Low Battery Restoral Report Code, SpreadNet Keypad/Keyfob Low BatteryReport Code, Accessory Tamper Report Code, Accessory Tamper RestoralBlock 6 Real Time Clock Programming Block 7 Auxiliary Devices Programming Timer Units On Board Relay Exit Delay TerminatorTimer Count On Board Relay Timer Units Remm #1, Relay #1Timer Count Remm #2, Relay #1 Timer Units Remm #2, Relay #1Timer Units Remm #8, Relay #2 Timer Count Remm #2, Relay #2Timed Relay Closing Timer #1 Hours Timed Relay Closing Timer #1 Day of WeekTimed Relay Closing Timer #1 Minutes Timed Relay Closing Timer #2 Day of WeekBlock 9 Partition Area Programming Block 8 SpreadNet ProgrammingFirst to Open/Last to Close Enable Comments Options Area Access by User Number User # 1Keypad Assignments to Areas Keypads 1 Area Assignments SpreadNet Keypads 1User Codes User # 1 Area Access SN Keyfob/Remote # 1Block 10 User Code Programming User Codes User Codes Comments