Sierra S5832SG installation instructions Sounder Turn-On Delay Following Alarm Seconds Comments

Page 23

Block 3 - Armed System Programming (cont.)

Sounder Turn-On Delay Following Alarm (Seconds)

Comments

Cmd Loc

Default

Range

034

0

0 - 255

Number of seconds that elapse following an alarm condition before the internal siren/external bell sounds. The keypad buzzer is active during this period.

Strobe/Siren Disable with Low Battery

Comments

Options:

Cmd Loc

Default

Range

035

2

1 - 2

If enabled, this option disables the strobe/siren, to extend

1

No

backup time with a low battery condition.

2

Yes

Phone Line Cut or Comm Fail Indication (Silent to Audible)

Cmd Loc

036

Default

1

Range

1 - 2

 

 

Comments

Options:

If enabled, alarm conditions programmed as silent will con-

1

No

vert to audible.

2

Yes

Phone Line Cut Audible Action

Cmd Loc

037

Default

1

Range

1 - 3

 

 

Comments

Options:

Determines the audible action

1

No Local Audible Annunciation.

to be taken when the tele-

2

Turn On Sounders.

phone line has been cut.

3

Turn On Sounders only if armed.

Internal/External Sounder Output Duration (Minutes)

Cmd Loc 038

Default 5

Range 0 - 60

Comments

Amount of time the internal siren and external bell will sound following an alarm condition. Sounder cadence is progammed in Block 2, CL 079 - 110.

Strobe Output Duration (Days)

Cmd Loc

039

Default

7

Range

0 - 7

 

 

Comments

This option specifies the duration of the strobe output (in days) following an alarm condition.

Options:

0Strobe Disabled 1 - 6 Days

7Strobe Latched

Soak Mode (Learning Period) Duration (Days)

Cmd Loc 040

Default 0

Range 0 - 31

Comments

Panel will operate as a local system only during this period. This will give the user time to learn the system. All alarm indications during this period will only be annunciated by keypad buzzer. The internal and external sound- ers are also disabled during this period.

Duress Active Only When (Area) Armed

Cmd Loc

041

Default

2

Range

1 - 2

 

 

Comments

Options:

If enabled, the duress code will only disarm the system. The

1

No

duress code may not be used for arming.

2

Yes

If disabled, this option will send a duress report when arming or disarming.

Opening Report Programming Override

Cmd Loc 042

Default 1

Range 1 - 2

Comments

Options:

An Opening Report will be sent if the following conditions

1

No

are met:

2

Yes

1 - An alarm has occurred;

2 - the cancel report timer (Block 4, CL 110) has expired; and 3 - a valid user code is entered.

The report is sent, regardless of the User Code Privileges (Block 1, CL 021 - 080) assigned to the user. The report will not override First to Open/Last to Close (Block 9, CL 110) option.

External Bell Supervision Enable

Cmd Loc

043

Default

1

Range

1 - 2

 

 

Comments

Options:

If enabled, provides for supervision of external bell wiring

1

No

for opens, shorts, and ground faults. Bell supervision re-

2

Yes

quires an EOL resistor at the bell terminals. This option may not be used if External Bell Reverse (Block 3, CL 048) is active.

For proper supervision, Ground Fault Supervision (Block 3, CL 053) should also be enabled.

19

Image 23
Contents Installation Instructions Page Table of Contents Singapore Sierra Accessory LoadingAH Requirements for Backup Country Specific Compliance InformationEarth Ground Panel Setup and InstallationIntroduction Mounting the PanelWiring Knock-outs Top AC Power Backup BatteryAH Requirements for Backup Sierra Accessory LoadingOutput Terminals Keypad WiringKeypad Wiring Sierra Accessory Wiring DistancesS5050 Relay/Event Memory Module AccessoriesZone Terminals On-Board Relay Terminals TB2S5058 Zone Expansion Module Digital Communicator Connections SN915-BUS SpreadNet ReceiverSN990/991 SpreadNet Keypad/Remote SN961 SpreadNet KeyfobTerminal Connections Programming the PanelRemote Programming RPS Zone LEDs Cmd Loc Data Value Press Home to activate the RPS featureProgramming With an LED Keypad ValueProgramming With an Icon Keypad Quick Programming ModeMenu Programming Mode Programming With an Alpha KeypadEvent Memory Installer Mode Options, BlockInstaller Walk-Test Battery Test Bypass 0 Home CancelEntry Delay Test Exit Delay TestBlock 1 Code Option Programming Block 2 Zone Configuration Programming Audible Cadence Zones 1 Chime Enable ZonesZone Bypass Enable Zones Zone Response Time Zones 1Block 3 Armed System Programming Low Battery Arming Comments Options Quick Bypass Enable CommentsHome Arm Exit Delay Enable 4X Exit Delay Extension Enable Comments OptionsSwinger Alarm Lockout Limit Comments Auto-Arming Enable AreaAuto-Disarming Enable Area Comments Auto-Disarming Enable Day of WeekDuress Active Only When Area Armed Sounder Turn-On Delay Following Alarm Seconds CommentsStrobe/Siren Disable with Low Battery Comments Options Soak Mode Learning Period Duration DaysHome Arming Enable Comments Options Keypad Tamper Switch Enable By Address Keypad #External Bell Reverse Enable Comments Options Sounder Bell Test Enable By Area CommentsBlock 4 Digital Communicator Programming Account #6 Account #3Account #4 Account #5Hour Zone Dial Delay Comments Options RPS Callback Enable CommentsKeypad RPS Enable Comments Alarm Dialing Delay Seconds CommentsKeypad and Accessory Tamper Report Routing Comments Power Supply Report RoutingInstaller Programming Report Routing Comments SpreadNet Transmitter Low Battery Report Routing CommentsBlock 5 Reporting Digits Programming Report Code, Tamper Zones 1 Report Code, Restoral Zones 1Report Code, Zone Bypass Zones 1 Comments Report Code, Trouble Zones 1 CommentsReport Code, Low Battery Report Code, Cancel Users 1 User #Report Code, AC Power Loss Report Code, AC Power RestoralReport Code, Ground Fault Restoral Report Code, Installer Programming StartReport Code, Installer Programming Complete Report Code, Ground FaultReport Code, Accessory Tamper Restoral Report Code, SpreadNet Keypad/Keyfob Low BatteryReport Code, SpreadNet Keypad/Keyfob Low Battery Restoral Report Code, Accessory TamperBlock 6 Real Time Clock Programming Block 7 Auxiliary Devices Programming Timer Units Remm #1, Relay #1 Exit Delay TerminatorTimer Units On Board Relay Timer Count On Board RelayTimer Count Remm #2, Relay #2 Timer Units Remm #2, Relay #1Timer Count Remm #2, Relay #1 Timer Units Remm #8, Relay #2Timed Relay Closing Timer #2 Day of Week Timed Relay Closing Timer #1 Day of WeekTimed Relay Closing Timer #1 Hours Timed Relay Closing Timer #1 MinutesBlock 9 Partition Area Programming Block 8 SpreadNet ProgrammingArea Assignments SpreadNet Keypads 1 Area Access by User Number User # 1First to Open/Last to Close Enable Comments Options Keypad Assignments to Areas Keypads 1User Codes User # 1 Area Access SN Keyfob/Remote # 1Block 10 User Code Programming User Codes User Codes Comments