Sharp FP-N40CX operation manual Remote Control USE, Filter Installation

Page 13

2 Filter Installation

1 After the True HEPA Filter is removed from the plastic bag, and place it in the main unit with the tabs facing up.

(See the diagram to the right.)

Ensure that the filter is installed correctly. Do not install the filter backwards or the unit will not operate properly.

2 After removing the Washable Active Carbon Filter from the plastic bag, place it on top of the True HEPA Filter with the bands (2 places) located in the upper most corners.

3 Next, place the Pre-Filter through the bands (2 places) located in the cor- ners of the Washable Active Carbon Filter.

Insert the tabs of the Pre-Filter into the associ- ated holes of the main unit.

4 Fill in the usage start date on the Date Label, which can be found near the upper edge of the Pre-Filter.

Use the date as a guide for your Filter Replace- ment schedule.

True HEPA Filter

Tabs

FRONT まえ

Ensure the bands are uppermost

Washable Ac-

tive Carbon Fil- ter

Holes in the main unit

BandPre-Filter

Tab(4 places)

Date Label

ENGLISH

REMOTE CONTROL USE

•Operate with the remote control facing the main unit (Re- ceiver).

• The signal range is about 23 feet (front).	Receiver
• Make sure there are no objects blocking the path of the	Transmitter
signal.
• A beep sound will be heard from the main unit when a
signal is received.

NOTE

• Avoid dropping or damaging the remote control. In addi- tion, be sure the remote control avoids moisture or place in direct sunlight or near a electric heater, etc., otherwise a malfunction may occur.

E-11

Image 13

Contents Floor / Tabletop type Type mobile FP-N40CXPage Filter Maintenance FeaturesContents For Your Protection the United States Consumer Limited Warranty for the U.S. Users Consumer Limited WarrantyFor Your Protection Canada Limited Warranty Periodically remove dust from the power plug Safety PrecautionsRisk of Electric Shock Use AC 120V onlyInstallation Guidelines Remote Control LimitationsFilter Guidelines Part Names CLEAN-SIGN LightMain Unit Display Accessories PlasmaclusterindicatorlightMounting the Stand BackInserting Batteries in the Remote Control Filter InstallationBattery Information PreparationFilter Installation Remote Control USEMain Unit Controls Main Unit OperationAuto CleanIon Control OffWashable Active Carbon Filter Care Care and MaintenanceCare Cycle Filter Cleaning Odor Sensor Main UnitReplacing the Filters Filter Replacement GuidelinesReplacing After replacing the filtersOperation Guide Can this filter be washed? When should I wash this filter?Will washing improve the filter’s performance? Remedy not a malfunction TroubleshootingStandby Power SpecificationsEnglish Page Entretien DU Filtre CaractéristiquesTable DES Matières Pour Téléphoner Composez le 1-905-568-7140 pour Pour Vous ProtégerGarantie Limitée Risque D’ÉLECTROCUTION Précautions DE SécuritéUtilisation uniquement avec du 120 V alternatif Guide D’INSTALLATION Limitations DE LA TélécommandePrécautions Concernant LE Fonctionnement DE CET Appareil Guide D’UTILISATION DU FiltreAffichage DE L’UNITÉ Principale Désignation DES PiècesVoyant de filtre VentilateurDOS DE L’APPAREIL AccessoiresRetirez le panneau avant Au sujet des piles Installation DU FiltreRemplacement du filtre Utilisation DE LA TélécommandeDans les coins supérieurs Utilisez la date pour déterminer la période deDE L’UNITÉ FonctionnementPrincipale AutoAutomatique Auto Nettoyage Clean LA TélécommandeContrôle d’ions ION Control Désactivé OFF Cycle d’entretien Soin ET EntretienTrempez le filtre environ 30 min- utes avant de le laver Rincez abondamment avec de l’eau propreNettoyagedufiltre Capteur D’ODEUR Unité PrincipaleRemplacement DES Filtres Guide DE Remplacement DES FiltresCas de remplacement Après le remplacement des filtresLe lavage va-t-il améliorer l’efficacité du filtre ? Guide D’UTILISATIONSolution pas un dysfonctionnement Résolution DES ProblèmesConsommation en veille CaractéristiquesEnglish Osaka, Japan New Jersey 07430-2135 U.S.A