HP 1GSa/s Digitizing Oscilloscope 16532A manual Paragraph No Test Results

Page 44

HP 16532A - Performance Tests

Table 3-1. Performance Test Record (Continued)

Paragraph No.		Test			Results

3-9	Voltage Measurement Accuracy		Channel 2
	(continued)		Zero Input	Measured		Actual
	Upper Limit	Lower Limit	Zero Input	Measured		Actual
	-13.7V	-14.3V	__________	__________		__________V
	-3.43V	-3.57V	__________	__________		__________V
	-1.37V	-1.43V	__________	__________		__________V
	-137.0mV	-143.0mV	__________	__________		__________mV
	143.0mV	137.0mV	__________	__________		__________mV
	1.43V	1.37V	__________	__________		__________V
	3.57V	3.43V	__________	__________		__________V
	14.3V	13.7V	__________	__________		__________V

3-10	Offset Accuracy		V/Div Setting		Reading	Actual
	Zero-input Offset-Channel 1		4V/Div	0.00V± 320.0mV		___________V
			4V/Div	0.00V± 320.0mV		___________V
			1V/Div	0.00V± 80.0mV		___________V
			100mV/Div	0.00V± 8.0mV		___________V
			10mV/Div	0.00V± 800.0μV		___________V
	Offset Accuracy		Supply	Min	Max	Actual
	DC Input Offset-Channel 1		-35.00V	-35.4V	-34.6V	-__________V
			-35.00V	-35.4V	-34.6V	-__________V
			-10.00V	-10.1V	-9.90V	-__________V
			-2.00V	-2.02V	-1.98V	-__________V
			+2.00V	+1.98V	+2.02V	+__________V
			+10.00V	+9.90V	+10.1V	+__________V
			+35.00V	+34.6V	+35.4V	+__________V
	Offset Accuracy		V/Div Setting		Reading	Actual
	Zero-input Offset-Channel 2		4V/Div	0.00V± 320.0mV		___________V
			4V/Div	0.00V± 320.0mV		___________V
			1V/Div	0.00V± 80.0mV		___________V
			100mV/Div	0.00V± 8.0mV		___________V
			10mV/Div	0.00V± 800.0μV		___________V
	Offset Accuracy		Supply	Min	Max	Actual
	DC Input Offset-Channel 2		-35.00V	-35.4V	-34.6V	-__________V
			-35.00V	-35.4V	-34.6V	-__________V
			-10.00V	-10.1V	-9.90V	-__________V
			-2.00V	-2.02V	-1.98V	-__________V
			+2.00V	+1.98V	+2.02V	+__________V
			+10.00V	+9.90V	+10.1V	+__________V
			+35.00V	+34.6V	+35.4V	+__________V

3-11	Bandwidth		Channel 1:
	≤ − 3.0dB		Actual Reading= ________ dB
			Channel 2:
			Actual Reading = ________ dB

3-18

Image 44

Contents HP 16532A Safety Considerations Safety SymbolsContents Section Replaceable Parts ServiceCalibration List of Tables Page Table of Contents Page Module Covered by This Manual Safety RequirementsIntroduction Accessories Supplied Accessories AvailableSpecifications Operating CharacteristicsHP 16532A Specifications Rise Time2 1.4 nsWaveform Record Length 8000 points Vertical dc Gain Accuracy4 ± 1.5% of full scaleTimebase HP 16532A Operating CharacteristicsVertical at BNC Triggering DigitizerTrigger Level Range Trigger ModesWaveform Display Display ModesMeasurement Aids Setup Aids Operating EnvironmentEquipment Critical Specifications Recommended Model USE Page Table of Contents Page Power Requirements Initial Inspection Safety RequirementsModule Installation Preparation for UseInstallation Considerations ProcedureEndplate Overlap Bottom Sequence Tagging for Service Operating EnvironmentStorage PackagingTable of Contents Page Performance Test Interval Performance Test ProceduresTest Record DC CAL Output Test AC CAL Output Test Input Resistance SpecificationEquipment Required Critical Specification Model/Part Number Page Voltage Measurement Accuracy Voltage Measurement Accuracy Test Div Offset Supply Upper Limit Lower Limit Procedure Zero-Input Offset Offset AccuracyDC Input Offset Div Offset Supply Min MaxBandwidth V1MHz Time Measurement Accuracy Menu Selection Setting Trigger Sensitivity RUN Repetitive Performance Test Record Paragraph No Test Results Yes No Page Table of Contents Page Maintaining System Integrity Calibration Protection SwitchCalibration Interval Instrument Warmup CalibrationSetting the PROTECT/UNPROTECT Switch to Unprotect Location of the PROTECT/UNPROTECT SwitchLoading the Default Calibration Factors Equipment Required for CalibrationCalibrate Vert Cal of the Self Cal menu as follows Calibrate Delay of the Self Cal menu as followsSelf Cal Menu Calibrations Calibrate the Time Null of the Self Cal menu as follows Calibrate the Logic Trigger of the Self Cal menu as followsCalibrate the Ext Trig Null of the Self Cal menu as follows Ext Trig Null Calibration ConnectionsSetting the PROTECT/UNPROTECT Switch to Protect Sealing the MainframeTable of Contents Page Replaceable Parts List AbbreviationsOrdering Information Exchange AssembliesDirect Mail Order System Reference Designator and Abbreviations Parts Identification Reference Designator HP Part Qty NumberDescription Mfr Code Mfr Part NumberPage Table of Contents Page Introduction Safety Requirements Module Block Diagram and The- ory of OperationMain Assembly Theory of Operation Attenuator Theory of OperationHP 16532A Oscilloscope Block Diagram Page Self-Test Access Procedure Self-TestsLoad Test System Screen Functional Tests Screen Touch the Functional Tests fieldA/D Test Run Screen Exit Test System Screen Self-Test Descriptions Data Memory TestTimebase Test TestTroubleshooting Troubleshooting AidsVerifying the System Clock Page 1 6 5 3 2 a Troubleshooting E E TTroubleshooting Sheet Troubleshooting E E T Troubleshooting E E T Troubleshooting E E T Troubleshooting E E T Oscilloscope Module Removal and Replacement Oscilloscope Module Removal ProcedureOscilloscope Module Replacement Procedure 12. Endplate Overlap Bottom SequenceTrigger Cable Removal and Replacement Trigger Cable Removal ProcedureAttenuator Removal Procedure Attenuator Removal and ReplacementTrigger Cable Replacement Procedure Attenuator Replacement Procedure Assistance WarrantyCertification