Raypak 850 LIMITED PARTS WARRANTY XFYRE - TYPE H and W, Models, Scope, Heat Exchanger Warranty

Page 54
LIMITED PARTS WARRANTY

LIMITED PARTS WARRANTY

XFYRE – TYPE H and W

MODELS 300-850

SCOPE

Raypak, Inc. (“Raypak”) warrants to the original owner that all parts of this heater which are actually manufactured by Raypak will be free from failure under normal use and service for the specified warranty periods and subject to the conditions set forth in this Warranty. Labor charges and other costs for parts removal or reinstallation, shipping and transportation are not covered by this Warranty but are the owner’s responsibility.

HEAT EXCHANGER WARRANTY

Space Heating (Closed Loop System)

Ten (10) year limited warranty from date of heater installation. This warranty applies only to boilers utilized in closed loop heating systems and hot water supply boilers that have been properly installed based upon manufacturer’s installation instructions.

Year of Claim

0-5

6

7

8

9

Percentage to be paid

 

 

 

 

 

by purchaser

0 %

20%

40%

60%

80%

Thermal Shock Warranty

Twenty (20) years from date of heater installation against “Thermal Shock” (excluded, however, if caused by heater operation at large changes exceeding 150°F between the water temperature at intake and heater temperature, or operating at heater temperatures exceeding 215°F).

ANY OTHER PART MANUFACTURED BY RAYPAK

One (1) year warranty from date of heater installation, or eighteen (18) months from date of factory shipment based on Raypak’s records, whichever comes first.

SATISFACTORY PROOF OF INSTALLATION DATE, SUCH AS INSTALLER INVOICE, IS REQUIRED. THIS WARRANTY WILL BE VOID IF THE HEATER RATING PLATE IS ALTERED OR REMOVED.

ADDITIONAL WARRANTY EXCLUSIONS

This warranty does not cover failures or malfunctions resulting from:

1.Failure to properly install, operate or maintain the heater in accordance with our printed instructions provided;

2.Abuse, alteration, accident, fire, flood and the like;

3.Sediment or lime build-up, freezing, or other conditions causing inadequate water circulation;

4.High velocity flow exceeding heater design rates;

5.Failure of connected system devices, such as pump or controller;

6.Use of non-factory authorized accessories or other components in conjunction with the heater system;

7.Failing to eliminate air from, or replenish water in, the connected water system;

8.Chemical contamination of combustion air or use of chemical additives to water.

PARTS REPLACEMENT

Under this Warranty, Raypak will furnish a replacement for any failed part. The failed part must first be returned to Raypak if requested, with transportation charges prepaid, and all applicable warranty conditions found satisfied. The replacement part will be warranted for only the unexpired portion of the original warranty. Raypak makes no warranty whatsoever on parts not manufactured by it, but Raypak will apply any such warranty as may be provided to it by the parts manufacturer.

TO MAKE WARRANTY CLAIM

Promptly notify the original installer, supplying the model and serial numbers of the unit, date of installation and description of the problem. The installer must then notify his Raypak distributor for instructions regarding the claim. If either is not available, contact Service Manager, Raypak, Inc., 2151 Eastman Avenue, Oxnard, CA 93030 or call (805) 278-5300. In all cases proper authorization must first be received from Raypak before replacement of any part.

EXCLUSIVE WARRANTY - LIMITATION OF LIABILITY

This is the only warranty given by Raypak. No one is authorized to make any other warranties on Raypak’s behalf. THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. RAYPAK’S SOLE LIABILITY AND THE SOLE REMEDY AGAINST RAYPAK WITH RESPECT TO DEFECTIVE PARTS SHALL BE AS PROVIDED IN THIS WARRANTY. IT IS AGREED THAT RAYPAK SHALL HAVE NO LIABILITY, WHETHER UNDER THIS WARRANTY, OR IN CONTRACT, TORT, NEGLIGENCE OR OTHERWISE, FOR ANY SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGE, INCLUDING DAMAGE FROM WATER LEAKAGE. Some states do not allow limitations on how long an implied warranty lasts, or for the exclusion of incidental or consequential damages. So the above limitation or exclusion may not apply to you.

This Limited Warranty gives you specific legal rights. You may also have other rights which may vary from state to state. We suggest that you complete the information below and retain this certificate in the event warranty service is needed. Reasonable proof of the effective date of the warranty (date of installation) must be presented; otherwise, the effective date will be based on the date of manufacture plus thirty (30) days.

Original Owner

Mailing Address

City

State

Zip Code

Daytime Telephone Number

Model Number

Serial Number

Date of Installation

Installation Site

Contractor/Installer

RAYPAK, INC • 2151 Eastman Avenue • Oxnard, CA 93030-9786 • (805) 278-5300 • Fax (800) 872-9725 • www.raypak.com

54

Image 54
Contents INSTALLATION & OPERATING INSTRUCTIONS WHAT TO DO IF YOU SMELL GASDo not try to light any appliance Models 300, 500 & Types H & WPage GENERAL SAFETY INSTALLATION CONTENTSBEFORE INSTALLATION WIRING DIAGRAM START-UPWARNINGS Pay Attention to These TermsProduct Receipt BEFORE INSTALLATIONInstallations at Elevation Model IdentificationComponent Locations General InformationGENERAL SAFETY Time/Temperature Relationships in ScaldsIndoor Installations INSTALLATIONInstallation Codes Outdoor InstallationsCombustion and Ventilation Air Indoor UnitsU.S. Installations1 Canadian Installations2Table F Vent/Air Inlet Termination Clearances Combustion Air Filter U.S. InstallationsConventional Combustion Air Supply Direct VentCanadian Installations Water PipingGeneral Temperature & Pressure Gauge Relief Valve Installation and PipingHydronic Heating Hydrostatic TestAir-Separation/ExpansionTank Three-WayValvesDomestic Hot Water Potable Water and Space Heating Gas Supply Connection Gas SupplyGas Supply Pressure Electrical Power Connections Check the Power Source Making the Electrical ConnectionsField-ConnectedControllers Field Wiring Connections Wiring the ThermostatWiring the Outdoor Sensor Wiring the Indirect SensorWiring the Cascade System Communication Bus 3.Create a hole to route the communication cables through where the dimples are in the side of the cabinet see Fig. 15, or route the wires to the rear junction box and out of the cabinet Cascade Master Pump and Sensor Wiring Cascade Follower Pump and Sensor Wiring VentingGeneral Configuration Support of Vent StackVent Terminal Location CombustionVenting Installation Tips Venting ConfigurationsVertical Venting Category Combustion Model No Volume ofCommon Venting Vent SizeFig. 21 Typical Common Venting Horizontal Through-the-WallDirectVenting Category Fig. 22 Horizontal Through-the-WallVentingModel No InstallationTermination Approved IntakesDirect Vent-Vertical Outdoor Installation Freeze ProtectionControls High Limit - Manual ResetHigh Limit - Auto Reset Optional Ignition Control FunctionsBlocked Vent Switch Flow SwitchHigh & Low Gas Pressure Switches Optional Low Water Cut-OffOptionalBlocked Condensate Drain Sensor Adjusting the XFyre SetpointOperating Instructions User MenuService Mode Status MenuStatus Menu 1 Items Status Menu 2 Items Installer Menu Items continued Installer Menu WIRING DIAGRAM Pre Start-up For Your SafetySTART-UP Pre Start-upCheckPreparation Start-UpBlower Check Finishing Safety InspectionManifold Check Follow-UpOPERATION Lighting InstructionsPost Start-UpCheck Heater Errors TROUBLESHOOTINGXFyre Error Codes Heater FaultsXFyre Fault Text Remedy FLUE / GAS PRESS F01Resistance ohms Sensor Resistance ValuesTemperature Sensors OutdoorPreventive Maintenance Schedule MAINTENANCESuggested Minimum Maintenance Schedule DailyAnnually WeeklySemi-Annually As RequiredCombustion Chamber Coil Cleaning Instructions NIOSH stated First AidAPPENDIX Inside Air Contamination248 CMR 5.082a1 through MODELS LIMITED PARTS WARRANTY XFYRE - TYPE H and WHEAT EXCHANGER WARRANTY SCOPENominal Factory Recommended Settings START-UPCHECKLIST FOR THE XFYREEMISSIONS SETTINGS AND TEST INFORMATION GAS SUPPLY DATA
Related manuals
Manual 8 pages 63.38 Kb Manual 8 pages 12.19 Kb

300, 850 specifications

Raypak is a renowned name in the heating industry, particularly known for its high-quality pool and spa heaters. Among their extensive product line, the Raypak 850, 500, 300, 400, and 700 models stand out for their reliability, efficiency, and cutting-edge technologies. Each model is designed to cater to different needs and applications while maintaining Raypak’s commitment to performance.

The Raypak 850 is designed for larger commercial pools or residential setups requiring high output. With a powerful heat exchanger made from copper and bronze, it ensures superior heat transfer and longevity. Its digital control system provides precise temperature regulation, enhancing user experience. Moreover, it features a durable construction with weather-resistant materials, ensuring lasting performance in various environments.

The Raypak 500 model offers a balance between efficiency and compactness. It features eco-friendly technology that reduces energy consumption without sacrificing performance. The integrated thermostat allows users to maintain consistent water temperatures, making it ideal for residential pools. This model is well-regarded for its user-friendly digital display, simplifying operation and monitoring.

For those needing a more moderate capacity, the Raypak 300 is an efficient choice. It combines robust engineering with an easy-to-use interface. Its advanced ignition system improves reliability while minimizing energy waste. The Raypak 300’s compact design allows for easy installation in various spaces, making it an excellent option for smaller pools.

The Raypak 400 heats water quickly and efficiently, making it suitable for both residential pools and spas. It features a high-capacity heating system that ensures optimal performance. With a clear LED display, users can easily monitor their settings, while the integrated diagnostics provide real-time feedback for maintenance and troubleshooting.

Lastly, the Raypak 700 model is known for its versatility and robust performance. It is equipped with advanced safety features, including a high limit switch and water flow detection mechanism, to ensure safe operation. The model's energy-efficient design enhances its eco-friendliness, making it a popular choice among environmentally conscious users.

Collectively, these Raypak models exemplify superior engineering, performance, and user-friendliness. Their innovative features ensure that they meet the varied demands of pool owners while providing reliable heating solutions for leisure and relaxation. Whether for commercial or residential use, the Raypak 850, 500, 300, 400, and 700 offer unmatched quality and efficiency.