Raypak 300, 850 operating instructions Combustion and Ventilation Air, Indoor Units

Page 9
Combustion and Ventilation Air

24”

SERVICE

CLEARANCE

24”

SERVICE

CLEARANCE

Heater

Min. Clearances

Recommended

from Combustible

Service

Side

Surfaces

Clearances

Rear

24”

24”

Right Side

0”

0”

Left Side

0”

0”

Top

Unobstructed

24”

Front

Open

24”

Vent

12”

12”

Termination

Table E: Clearances — Outdoor Installations

Combustion and Ventilation Air

NOTE: Use of this boiler in construction areas where fine particulate matter, such as concrete or dry-wall dust, is present may result in damage to the boiler that is not covered by the warranty. If operated in a construction environment, a clean source of combustion air must be provided directly to the boiler.

24”

SERVICE

CLEARANCE

Venting not shown for clarity. Heater must be vented per

instructions in this manual

Fig. 4: Minimum Clearances from Combustible Surfaces — Indoor and Outdoor Installations

Indoor Units

This heater must be supplied with sufficient quantities of non-contaminated air to support proper combustion and equipment ventilation. Combustion air can be sup- plied via conventional means where combustion air is drawn from the area immediately surrounding the heater, or via direct vent, where combustion air is drawn directly from outside. All installations must com- ply with the requirements of the NFGC (U.S.) and B149 (Canada), and all local codes.

CAUTION: Combustion air must not be contaminated by corrosive chemical fumes which can damage the boiler and void the warranty. (See the Appendix.)

NOTE: It is recommended that the intake vent be insulated in cold climates to minimize sweating.

9

Image 9
Contents Do not try to light any appliance WHAT TO DO IF YOU SMELL GASINSTALLATION & OPERATING INSTRUCTIONS Models 300, 500 & Types H & WPage BEFORE INSTALLATION CONTENTSGENERAL SAFETY INSTALLATION WIRING DIAGRAM START-UPPay Attention to These Terms WARNINGSInstallations at Elevation BEFORE INSTALLATIONProduct Receipt Model IdentificationGeneral Information Component LocationsTime/Temperature Relationships in Scalds GENERAL SAFETYInstallation Codes INSTALLATIONIndoor Installations Outdoor InstallationsIndoor Units Combustion and Ventilation AirU.S. Installations1 Canadian Installations2Table F Vent/Air Inlet Termination Clearances Conventional Combustion Air Supply U.S. InstallationsCombustion Air Filter Direct VentCanadian Installations Water PipingGeneral Hydronic Heating Relief Valve Installation and PipingTemperature & Pressure Gauge Hydrostatic TestAir-Separation/ExpansionTank Three-WayValvesDomestic Hot Water Potable Water and Space Heating Gas Supply Connection Gas SupplyGas Supply Pressure Electrical Power Connections Check the Power Source Making the Electrical ConnectionsField-ConnectedControllers Wiring the Thermostat Field Wiring ConnectionsWiring the Outdoor Sensor Wiring the Indirect SensorWiring the Cascade System Communication Bus 3.Create a hole to route the communication cables through where the dimples are in the side of the cabinet see Fig. 15, or route the wires to the rear junction box and out of the cabinet Cascade Master Pump and Sensor Wiring Cascade Follower Pump and Sensor Wiring VentingGeneral Vent Terminal Location Support of Vent StackConfiguration CombustionVenting Installation Tips Venting ConfigurationsVertical Venting Category Combustion Common Venting Volume ofModel No Vent SizeVenting Category Horizontal Through-the-WallDirectFig. 21 Typical Common Venting Fig. 22 Horizontal Through-the-WallVentingTermination InstallationModel No Approved IntakesDirect Vent-Vertical Freeze Protection Outdoor InstallationHigh Limit - Auto Reset Optional High Limit - Manual ResetControls Ignition Control FunctionsHigh & Low Gas Pressure Switches Optional Flow SwitchBlocked Vent Switch Low Water Cut-OffOptionalOperating Instructions Adjusting the XFyre SetpointBlocked Condensate Drain Sensor User MenuStatus Menu Service ModeStatus Menu 1 Items Status Menu 2 Items Installer Menu Items continued Installer Menu WIRING DIAGRAM START-UP For Your SafetyPre Start-up Pre Start-upCheckPreparation Start-UpBlower Check Manifold Check Safety InspectionFinishing Follow-UpOPERATION Lighting InstructionsPost Start-UpCheck XFyre Error Codes TROUBLESHOOTINGHeater Errors Heater FaultsXFyre Fault Text FLUE / GAS PRESS F01 RemedyTemperature Sensors Sensor Resistance ValuesResistance ohms OutdoorSuggested Minimum Maintenance Schedule MAINTENANCEPreventive Maintenance Schedule DailySemi-Annually WeeklyAnnually As RequiredNIOSH stated First Aid Combustion Chamber Coil Cleaning InstructionsInside Air Contamination APPENDIX248 CMR 5.082a1 through HEAT EXCHANGER WARRANTY LIMITED PARTS WARRANTY XFYRE - TYPE H and WMODELS SCOPEEMISSIONS SETTINGS AND TEST INFORMATION START-UPCHECKLIST FOR THE XFYRENominal Factory Recommended Settings GAS SUPPLY DATA
Related manuals
Manual 8 pages 63.38 Kb Manual 8 pages 12.19 Kb

300, 850 specifications

Raypak is a renowned name in the heating industry, particularly known for its high-quality pool and spa heaters. Among their extensive product line, the Raypak 850, 500, 300, 400, and 700 models stand out for their reliability, efficiency, and cutting-edge technologies. Each model is designed to cater to different needs and applications while maintaining Raypak’s commitment to performance.

The Raypak 850 is designed for larger commercial pools or residential setups requiring high output. With a powerful heat exchanger made from copper and bronze, it ensures superior heat transfer and longevity. Its digital control system provides precise temperature regulation, enhancing user experience. Moreover, it features a durable construction with weather-resistant materials, ensuring lasting performance in various environments.

The Raypak 500 model offers a balance between efficiency and compactness. It features eco-friendly technology that reduces energy consumption without sacrificing performance. The integrated thermostat allows users to maintain consistent water temperatures, making it ideal for residential pools. This model is well-regarded for its user-friendly digital display, simplifying operation and monitoring.

For those needing a more moderate capacity, the Raypak 300 is an efficient choice. It combines robust engineering with an easy-to-use interface. Its advanced ignition system improves reliability while minimizing energy waste. The Raypak 300’s compact design allows for easy installation in various spaces, making it an excellent option for smaller pools.

The Raypak 400 heats water quickly and efficiently, making it suitable for both residential pools and spas. It features a high-capacity heating system that ensures optimal performance. With a clear LED display, users can easily monitor their settings, while the integrated diagnostics provide real-time feedback for maintenance and troubleshooting.

Lastly, the Raypak 700 model is known for its versatility and robust performance. It is equipped with advanced safety features, including a high limit switch and water flow detection mechanism, to ensure safe operation. The model's energy-efficient design enhances its eco-friendliness, making it a popular choice among environmentally conscious users.

Collectively, these Raypak models exemplify superior engineering, performance, and user-friendliness. Their innovative features ensure that they meet the varied demands of pool owners while providing reliable heating solutions for leisure and relaxation. Whether for commercial or residential use, the Raypak 850, 500, 300, 400, and 700 offer unmatched quality and efficiency.