Home Automation SECURITY SYSTEM owner manual Onhk - On Hook, Offhk - Off Hook, Ring - Ringing

Page 39

3 = SUN (SUNRISE / SUNSET AUTOMATIC CALCULATION)

The system automatically calculates the time of sunrise and sunset each day. From the status menu, press the 3 (SUN) key on the console keypad to display the calculated time of sunrise, sunset, and the outdoor temperature (if outdoor temp sensor installed):

Sunrise: 6:00

AM

Temp

Sunset: 5:58

PM

85

4 = TEST (SYSTEM DIAGNOSTIC TEST)

The diagnostic test performed by the OmniLT allows you to check the status of the battery, telephone, bell circuit, auxiliary fuse, and security zone loop readings. The display is updated 3 times per second, although the actual readings are taken 10 times per second. To enter the Test menu, from the Status menu, press the 4 (TEST) key on the console keypad.

The first display shows the current battery reading and the phone line status. A battery test is initiated when the status mode is first entered. The new battery reading is updated ten seconds later. The low battery limit is also displayed.

The phone status consists of two parts, separated by a "/". The first part shows the current phone line state:

ONHK - ON HOOK

OFFHK - OFF HOOK

RING - RINGING

DEAD - DEAD PHONE LINE

The second part shows how the OmniLT is currently using the phone line:

IDLE - NOT USING THE PHONE LINE

LOCAL - LOCAL ACCESS

REMOTE - REMOTE ACCESS

VOICE - IN VOICE DIAL OUT MODE

EMGACC - ACCESS AFTER VOICE DIAL OUT

DCM - IN DIGITAL COMMUNICATOR MODE

BATTERY:

230 (LIMIT 200)

PHONE:

ONHK/IDLE

Next, the display shows the A/D reading for the battery voltage, phone line voltage, AC power on, bell, and fuse:

BAT:

225

PHONE: 140

ACON:

82

BELL: 215

FUSE: 222

The next series of displays shows the current analog reading for each security zone input. The displays show the readings for zones 1-32.

1= 46 2= 47 3= 46 4= 45 5= 46 6= 47

THROUGH

19= 47 20= 48 21= 47 22= 46 23= 46 24= 47

The normal loop reading for a zone is between 36 - 59 when the zone is secure. Each reading should be changing only by two or three counts from its average steady reading. When a door or window is opened, the reading will go to a value that represents that zone being open. If Zone 8 is a Supervised Fire Zone, the normal reading is between 26 – 43 when the zone is secure.

This feature can be used to monitor the quality of the zone wiring and contacts. If the numbers begin to deviate from their original values when the system was new, wiring problems that will eventually lead to trouble or false alarms may be developing. You may wish to record the Status Test values for future reference.

5 = TEMP (TEMPERATURE)

35

Image 39
Contents Document Number 21R00-1Rev. January Copyright 2000-2006HAI All Rights Reserved Document Number 21R00-1Rev. JanuaryContents OVERALL DESCRIPTIONSECURITY SYSTEM OPERATION CONTROLTELEPHONE CONTROL SETUPUnderwriters Laboratories UL Listing INTRODUCTION2- DAY OVERALL DESCRIPTIONConsole Operation 1- OFF7- CONSOLE LED Normal Top-LevelDisplayDisplay Menus 6- UP ARROWTo silence the beeper, press the * key Error BeepsMain Menu Trouble BeepsTime Out OmniLT MaintenanceCancel Confirmation Beep1 = DAY SECURITY SYSTEM OPERATIONArming the Security System 0 = OFF4 = VACATION Using Shortcut Keys2 = NIGHT 3 = AWAYRestoring Zones 9 = RESTOREQuick Arm Bypassing ZonesWhat To Do When You Come Home What Happens When the Alarm is ActivatedBurglar Alarm Activated OMNI Fire Alarm ActivatedGas Alarm Activated Emergency KeysPolice Emergency Duress Code Entered or Duress Alarm ActivatedAlarm Reset Alarm CancelTrouble Indications CodesMaster Code User Code Panic SwitchesTesting Your System Manager CodeAbout UPB CONTROLAbout Rooms When set to UPB, the OmniLT controller canRoom Controller LED Indicators HAI Lighting Control HLC FormatAbout CentraLite When set to CentraLite, the OmniLT controller canAbout Lutron RadioRA About House ControllersHouse Code When set to RadioRA, the OmniLT controller canAbout ALC AboutControlling a Room of HLC Lighting Configuring Lighting Scenes in an HLC RoomScrolling Through Names Controlling UnitsStep OperationControlling CentraLite Units Controlling ALC or X-10Units Controlling RadioRA UnitsControlling Compose Units Timed CommandsRamp Command ALC Scene Command ComposeStatus of a Unit Internal FlagsControlling Outputs All On / Off All Lights OnAll Off Leviton Scene Control Scene CommandsScene Set Command Scene On CommandActivating and Deactivating Links Scene Off CommandSetting a Link Lighting Scenes UPB LinksLeave for Work Button ButtonsExecuting Phantom Buttons Executing CentraLite ScenesTemperature Control HAI RC-SeriesThermostatsDinner for Two Button For HAI heat/cool thermostats Programmable Energy Saver Modules PESMs Control actions for temperature sensors Upstairs 2=LOW 3=HIGH #=STAT Freeze AlarmsIMPORTANT NOTES Indoor and Outdoor TemperatureTemperature Control of Appliances Temperature AlarmsHumidity StatusConfiguring HLC Devices using an Omni Console Configuring HLC DevicesStep Operation Setup Mode for HLC DevicesStep Operation Step OperationDEAD - DEAD PHONE LINE ONHK - ON HOOKOFFHK - OFF HOOK RING - RINGINGShow Events Event LogMessages Show MessageLog Message Send Message Pro-Link Clear MessageSay Message Phone MessagePro-Linkalso has the capability to monitor the serial port for incoming text messages. When a text message is received, Pro-Linksearches through all 16 messages for a matching message. If one is found, the Program Command macro corresponding to the matching message is activated Remote Phones TELEPHONE CONTROLTelephone Interface In-HousePhonesPhone Access Denied - Remote Lockout Alternate MethodMain Menu Recording Your Address PC AccessWhen a Two-WayAudio Module is being used Panic Button over the Phone # # # # # #How the OmniLT Voice Dialer Works Emergency Dial-OutDigital Dialer Voice DialerEntering the Code What You Hear - If Your OmniLT Calls You2 = Manager SETUPSet Up Codes 1 = MasterDuress Code Set Up TimeSet Up Programs TIME2 = Show Programs 1 = Add Programs3 = Delete All Programs Edit Programs Edit Programs WhenTimes Programs Button and Event Programs Control Unit / Switch Press Event ButtonsUPB 6-ButtonKeypad Corresponding Switch TableSwitch OmniLTAll On/Off Event Buttons Zone Event ButtonsAlarm Event Buttons UPB Link TriggersX-10Event Buttons Message Event Buttons Pro-Link Miscellaneous Event ButtonsEdit Program Command Switch Press Event Buttons CentraLiteProgram Control Commands WHEN LINK 1 ON Porch Light STATUS Unit Toggle CommandProgram Security Commands Program Button CommandsEdit Program Condition Program All On / All Off CommandsProgram Video Commands Program Message CommandsProgram Other Conditions Program Security Mode ConditionsProgram Zone Conditions Program Time Clock ConditionsSet Up Dial Telephone AccessAnswer Outside Call My Phone Number Remote CommandsRings Before Answer Dial TypeEntry Delay Set Up ArmingDial Out Numbers Dial OrderExit Delay Enable Quick ArmEnable Auto Bypass All On For AlarmFlash For Alarm Set up MiscellaneousAnnounce Alarms Enable Freeze AlarmHouse Code All Off FORMATNUMBER DESCRIPTIONZONE NAME Latitude, Longitude, and Time ZoneDESCRIPTION Set Up NamesDaylight Savings NUMBERSet Up Voice Set Up Address FIRE ESCAPE PLANNING UNDERWRITERS LABORATORIES REQUIREMENTSHAI 21487 Bayou Ct Abita Springs, LA FEDERAL COMMUNICATION COMMISSION NOTICECANADIAN INDUSTRY CANADA NOTICE MAXIMUM APPENDIX A - SPECIFICATIONSCONTROLLER OUTPUTS UL RATINGSCODE CHAR APPENDIX B - CHARACTER CODESCODE CHAR CODE CHARCODE APPENDIX C - VOICE DESCRIPTIONSCODE DESCRIPTIONDESCRIPTION CODEDESCRIPTION CODECODE DESCRIPTION CODE DESCRIPTIONPage HAI New Orleans, LA U S A NOTE TO INSTALLER