Jotul Woodstove F 400 manual Operation, Use Solid Wood Fuel Only, Controls on the Jøtul F

Page 10

USA/Canada

Operation

Please read the following section completely, before building a fire in your new Jøtul F 400 .

Use Solid Wood Fuel Only

First this stove is designed to burn natural wood only.Wood that has been air-dried for a period of 6 to 14 months will provide the cleanest, most efficient heat.

Do not burn:

*Treated or painted wood

*Coal

*Garbage

*Chemical Chimney cleaners

*Cardboard

*Colored paper

*Solvents

*Any synthetic fuel or logs

The burning of any of these materials can result in the release of toxic fumes. Never use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter fluid, or similar liquids to start or “freshen-up” the fire. Always keep such liquids away from the heater at all times.

Important: Never build or allow the fire to rest directly on the glass panel. The logs should always be spaced at least one inch from the glass to allow for proper air flow within the firebox.

Controls on the Jøtul F 400

Combustion air is controlled by the Primary Air Lever, located above the ashlip on the front of the stove. The lever actuates a shutter over the air inlet which regulates the volume of primary air entering the firebox and affects heat output and burn time.

When first starting or reviving the fire: the primary control lever should be at the far right position, which allows the maximum amount of air into the stove. The greater the amount of air entering the stove, the hotter and faster the fire will burn. Moving the lever to the left reduces the airflow into the stove which prolongs the fire at a lower heat output. See figure 11.

Air Flow / Performance

Primary air enters the firebox directly above the glass panel on the door. The incoming air creates a turbulent barrier or “airwash” between the glass and the fire. Reducing the flow of primary air directly reduces the effectiveness of the airwash. Determining the primary air setting for the best overall performance for your particular needs and installation will only be established over time through trial and error.

Break-In Procedure

The Jøtul F 400 is constructed of cast iron and stove furnace cement. This type of construction requires the stove to be “broken-in” gradually so that heat expansion

does not occur too quickly and cause damage. The following steps describe the proper break-in procedure for the Jøtul F 400 :

1.Light a small fire of newspaper and kindling. Only allow the stove to reach a maximum surface temperature of 200°F (93° C). Burn for approximately 1 hour.

2.Allow the stove to cool to room temperature.

3. Light a second fire, allowing the stove to reach a maximum temperature of 300°F (149°C) for 1 hour.

4.Cool the stove to room temperature.

5.Light a third fire and gradually allow the stove to reach a surface temperature of 400°F (204°C).

6. Cool stove to room temperature. This completes the “break-in” procedure.

To monitor the stove’s temperature, use a magnetic stove- top thermometer, placed directly on the corner of the stove’s top plate.

Note: Keep the stove under 400°F (204°C) surface temperature during any “break-in fire”, with the exception of the last “break-in” fire. If the temperature exceeds 400°F, move the primary air control lever all the way to the left to shut off the air supply completely. It is normal that the stove top temperature will continue to climb until the fuel burns down somewhat. Once the fire is out and the stove has cooled to room temperature, continue the break- in procedure. Never attempt to reduce the temperature by removing burning logs from the fire.

Note: It is normal for a new painted stove to emit an odor and smoke during its first several fires. This is caused by the seasoning of the high temperature paint and will diminish with each fire. Opening a window or door to provide additional ventilation will alleviate this condition.

Starting and Maintaining a Fire

Burn only solid wood directly on the bottom grate of the stove. Do not elevate the fire in any way.

The ash pan door on the stove must always be securely closed when the stove is in operation.

Burning the stove with the Ash Door open will over-fire the stove and cause interior damage.

1.With the primary air control lever in the full open position (to the right), start with several sheets of crumbled newspaper placed directly on the grate. On top of the newspaper, place several pieces of small dry kindling (approx. 1” in diameter) with two to three larger logs (approx. 3” to 5” in diameter) on top.

2.Light the fire and close the door, slowly building the fire by adding larger and larger logs. Be sure to follow the break-in procedure before creating a hot fire that might damage the stove.

3.Once the stove has reached a surface temperature range of between 400° and 600°, (204°C -316°C), adjust the primary air control lever as necessary to generate the heat output and burn time desired.

Jøtul recommends use of a magnetic stove top thermometer to monitor the surface temperature of the stove. The optimum surface temperature range for

10

Image 10
Contents Jøtul F Standards Check Building CodesInstallation Safety NoticesTable of Contents Chimney Requirements Assembly Before InstallationMasonry Chimneys Chimney Height Prefabricated ChimneysWall Pass-Throughs Hearthmount into a Masonry Fireplace Clearance to CombustiblesMasonry Chimney Clearances to Walls and CeilingsAlcove Installation Using Shields to Reduce ClearancesMobile Home Installation Unprotected Surface Corner InstallationJøtul F 400 Woodstove Clearances Parallel to the WallPER NFPA211 or CAN/CSA -B365-M93 Side Rear CornerUse Solid Wood Fuel Only Break-In ProcedureOperation Controls on the Jøtul FAsh Removal MaintenanceAdding Fuel Glass CareGeneral Maintenance AccessoriesFloor Bracket Kit #750304 Stove-Top Thermometer #Outside Air Kit #154335 Rear Heat Shield #25 3/4 23 1/4 29 1/2 top exit 25 1/2 rear exit 28 1/2 26 1/2 USA/Canada Draw. no USA/Canada Appendix a Parts list for the Jøtul F 400 woodstoveConsult your dealer for part numbers and replacement parts Alternate floor protectionPage Norsk Forhold til myndighetene InnholdInstallasjon av Jøtul F Montering av røykrør Kontroll av funksjoner figTilslutning til skorstein Bruksanvisning VedlikeholdServicearbeider EkstrautstyrSvenska Innehåll SäkerhetsreglerInstallation av Jøtul F Anslutning till skorsten Kontroll av funktionerMontering av rökrör Första gångs upptändning och dagligt användandeUnderhåll Servicearbeten Extrautrustning/tillbehörPre-installation checks Table of contentsRelationship to the authorities Installation of Jøtul F Mounting of flue pipe Assembly prior to installationControl of functions fig Connection to chimneyOperating instructions Cleaning the glassCleaning and soot removal Initial lighting and daily useService Optional equipmentRéglementations nationales Table des matieresInstallation du poêle Jøtul F400 Montage du tuyau de raccordement Mise en service et usage courantMise en service Raccordement à la cheminéeEntretien Accessoires optionnels RevisionÍndice de contenido Comprobaciones previas a la instalaciónInstalación de Jøtul F Instalación del conducto de humos Montaje previo a la instalaciónControl de funciones fig Conexión a la chimeneaLimpieza del cristal MantenimientoEncendido inicial y uso diario Eliminación de la cenizaConservación Equipo opcional Sustitución de la placa deflectoraConformità alle leggi Indice generaleInstallazione di Jøtul F Collegamento alla cappa Controllo delle funzioni figMontaggio del condotto Prima accensione e utilizzo quotidianoEliminazione della cenere ManutenzionePulizia del vetro Pulizia del camino ed eliminazione della fuliggineRiparazione Dotazione facoltativaBehördliche Auflagen InhaltAufstellen des Jøtul F Steuergeräte Abb Installation des AbzugsrohrsZusammenbau vor der Aufstellung Anschluss an den SchornsteinInbetriebnahme InbetriebnahmeInbetriebnahme und täglicher Gebrauch Täglicher GebrauchPflege Austausch der Hitzeschutzplatten InstandhaltungAustausch der Umlenkplatte Wettelijke voorschriften Controle voor de installatieInhoudsopgave Installatie van de Jøtul F Plaatsing van de kachelpijp GebruiksaanwijzingControle van de functies afb SchoorsteenaansluitingOnderhoud Optionele accessoires Groot onderhoudPage Page Page Page Quality KvalitetQualität Qualité

Woodstove F 400 specifications

The Jotul F 400 is a leading model in the Jotul line of woodstoves, renowned for its combination of efficiency, aesthetics, and robust craftsmanship. As one of the company's most popular models, it seamlessly blends functionality with timeless design, making it an ideal choice for both contemporary and traditional spaces.

One of the primary features of the Jotul F 400 is its impressive heating capacity. With an ability to heat spaces of up to 2,000 square feet, this woodstove is perfect for larger rooms or open floor plans. Its firebox can accommodate logs up to 20 inches in length, allowing for longer burn times and fewer refuels. With an average efficiency rating of around 78%, the F 400 ensures that most of the wood's energy is converted into usable heat rather than lost up the chimney.

In terms of design, the Jotul F 400 showcases the classic Norwegian aesthetic that Jotul is known for. Its cast iron construction not only contributes to its durability but also aids in heat retention, ensuring that the stove continues to radiate warmth long after the fire has diminished. The intricate detailing and optional enamel finishes give it an elegant touch, making it a statement piece in any home.

The Jotul F 400 is equipped with advanced combustion technology that promotes a cleaner burn, resulting in reduced emissions. This feature is particularly important in today’s environmentally conscious market, as it aligns with stricter regulations on woodstove emissions. The stove features a secondary combustion system that helps to maximize fuel efficiency while minimizing smoke output, allowing users to enjoy the ambiance of a wood fire without excessive pollutants.

Another notable characteristic of the F 400 is its easy-to-use air control system. This allows users to easily adjust the airflow to the fire, optimizing it for lighting, burning, and maintaining desired temperatures. The large, self-cleaning glass door provides an unobstructed view of the flames, enhancing the ambiance of any room.

In summary, the Jotul F 400 woodstove is a blend of efficiency, beauty, and innovation. Its capacity to heat large spaces, coupled with advanced combustion technology and classic design, makes it one of the top choices for homeowners looking for a reliable and attractive heating solution. Whether for cozy evenings or efficient heating, the Jotul F 400 is sure to enhance any living space.