Heat & Glo LifeStyle 2137-900 owner manual Finishing, Facing Material

Page 32

11 Finishing

A. Facing Material

WARNING

Fire Risk.

Do NOT obstruct air inlet or outlet grilles.

Do NOT modify grilles.

•Modifying or covering grilles could cause

temperature rise and ﬁre hazard. Finishing materials must not interfere with:

•Air ﬂow through grilles or louvers.

•Operation of louvers or doors.

•Access for service.

FINISH WALL MATERIAL MAY BE

COMBUSTIBLE - TOP AND SIDES

	8 in.	NON-COMBUSTIBLE ZONE
	8 in.	0 in.
		0 in.
		31-11/16 in.

0 in.										0 in.

SEALANT MATERIAL

WARNING

Fire Risk.

Finish all edges and fronts to clearances and speciﬁcations listed in manual.

•Black metal appliance front may be covered with noncombustible material only.

•Do NOT overlap combustible materials onto appliance front.

•Install combustible materials up to speciﬁed clearances on top, front and side.

•Seal joints between the ﬁnished wall and appliance top and sides using only a 300ºF minimum sealant.

B.Mantel Projections

A Studio front is required for all installs. No mantels are allowed when using Studio fronts.

Figure 11.1 Noncombustible Facing Diagram

WARNING

Risk of Fire

•Non-combustible clearances MUST be maintained.

•Sheetrock, wood or other combustibles must NOT be used as sheathing or facing in the non-combustible zone.

•See Section 11 for proper clearances.

•See Section 1 for combustible/non-combustible deﬁnitions.

32	Heat & Glo • Soho24B • 2137-900 Rev. P • 8/12

Image 32

Contents Hot glass will cause burns Model Soho24BWhat to do if you smell gas Congratulations Homeowner Reference InformationTable of Contents Listing and Code Approvals Installation of Carbon Monoxide Detectors Requirements for the Commonwealth of MassachusettsTools and Supplies Needed Installation to ensure maximum safety and beneﬁtGetting Started Mantel Projections Framing and ClearancesSelecting Appliance Location Constructing the Appliance Chase ClearancesSee .4 for speciﬁc clearances Termination LocationsVent Termination Minimum Clearances Covered Alcove Applications Inches U.S.AVent Information and Diagrams Vent Table KeyUse of Elbows Measuring StandardsVent Diagrams Top Vent Horizontal Termination One ElbowTwo Elbows Minimum MaximumTop Vent Horizontal Termination Three Elbows V1 Min H1 Max V2 Min H2 MaxV1 Minimum H1 Maximum V1 + Top Vent Vertical Termination No ElbowV1 = 45 ft Max .72 m V1 = 3 ft Min mm Top Vent Vertical Termination Three Elbows V1 Minimum H1+ H2 Maximum V1+ V2 MinimumVent Clearances and Framing Pipe Clearances to CombustiblesWall Penetration Framing Combustible Wall PenetrationVertical Penetration Framing Pipe SLPVaulted Ceiling Installation Install Attic Insulation ShieldFlat Ceiling Installation Appliance Preparation Top VentInstallation of Non-combustible Facing Material MaterialSecuring and Leveling the Appliance Proper Positioning, Leveling and Securing of aInstalling Vent Pipe Assemble Vent SectionsAssemble Slip Sections Secure the Vent SectionsInstall Decorative Ceiling Components Disassemble Vent SectionsInstall Metal Roof Flashing Assemble and Install Storm CollarHeat Shield Requirements for Horizontal Termination Install Vertical Termination CapInstall Decorative Wall Components Install Horizontal Termination Cap 17 Venting through the wallGas Information Fuel Conversions Gas ConnectionGas Pressures Pressure Natural Gas PropaneHigh Altitude Installations Recommendation for Wire Electrical InformationJunction Box Installation GRN wire Ground attached To GRN screw with Inside boxSee for combustible/non-combustible deﬁnitions FinishingFacing Material Installation of Non-Combustible Facing Materials PaintingAppliance Setup Clean the ApplianceAccessories Remove Shipping MaterialsStone Placement Soho24B Positioning StonesNo Stones in this Area Glass Assembly Air Shutter SettingRemoving Glass Assembly Replacing Glass AssemblyOperating Instructions Before Lighting ApplianceLighting Instructions IPI Final inspection byAfter Appliance is Lit Frequently Asked QuestionsInitial Break-in Procedure Sympton Possible Cause Corrective Action TroubleshootingIntelliFire Ignition System Symptom Possible Cause Corrective Action Maintenance Tasks Maintaining and Servicing ApplianceInspect Maintenance Tasks Recommend addition of screen if one is not presentAppliance Dimension Diagram Appliance Dimensions TableReference Materials Location Inches MillimeterVent Components Diagrams SL Series Components B. Vent Components Diagrams Assembly 356 mm 330 mm 305 mm12-1/2 318 mmService Parts StockedAt Depot 24 x 24 Direct Vent Fireplace#11 IPI Valve Assembly SOHO24B-ONYX No longer availableLimited Lifetime Warranty Limited Lifetime WarrantyWarranty Conditions Contact Information