Regency P33-NG3, P33-LP3 installation manual Optional Wall Switch, Thermostat Wire Table

Page 33

INSTALLATION

OPTIONAL	OPTIONAL
WALL THERMOSTAT	REMOTE CONTROL

OPTIONAL

WALL SWITCH

A wall thermostat may be installed if desired, connect the wires as per the wiring diagram. Use table below to determine the maximum wire length.

Note: Preferableifthethermostatisinstalled on an interior wall.

Regency offers an optional programmable thermostat but any 250-750 millivolt rated non- anticipator type thermostat that is CSA, ULC or UL approved may be used.

CAUTION

Do not wire millivolt wall thermostat wires to 120V wire.

Thermostat Wire Table

Recommended Maximum Lead Length

(Two-Wire) When Using Wall

Thermostat (CP-2 System)

	Wire Size	Max. Length

	14 GA.	50	Ft.
	16 GA.	32	Ft.
	18 GA.	20	Ft.
	20 GA.	12	Ft.
	22 GA.	9	Ft.

Use the Regency Remote Control Kit approved for this unit. Use of other systems may void your warranty.

The remote control kit comes with a hand held transmitter, a receiver and a wall mount- ing plate.

1)Choose a convenient location on the wall to install the receiver and the receptacle box (protection from extreme heat is very important). Run wires from the ﬁ replace to that location. Use Thermostat Wire Table.

2)Connect the two wires to the gas valve. See diagram below.

CAUTION

Do not wire millivolt remote control wires to 120V wire.

3)Install 3AAAalkaline batteries in transmitter and 4 AA alkaline batteries in the receiver. Install the receiver and its cover in the wall. Switch the remote receiver to "remote" mode. The remote control is now ready for operation.

1)Runthesupplied15'ofwirethroughtheright or left side gas inlet opening. Be careful not to damage wire.

Note: We recommend a maximum of 15' of wire but if you wish to go with a longer run, use the Thermostat Wire Table.

2)Connect the wire to the supplied wall switch and install into the receptacle box.

CAUTION

Do not wire millivolt

wall switch wire

to 120V wire.

Regency P33-3 Zero Clearance Direct Vent Gas Fireplace

Image 33

Contents P33-3 Zero Clearance To the New Owner Information for MOBILE/MANUFACTURED Homes After First SaleTable of Contents Safety Label General Safety Information InstallationSave These Instructions Before YOU StartUnit Dimensions Installation ChecklistLocating Your GAS Stove Duct System OptionMantel LEG Clearances Clearancescombustible MantelsClearances are not adhered to Fire hazard is an extreme risk if theseRear Termination Framing and FinishingSimpson Dura-Vent Minimum Clearances Vertical Termination or Vertical Rise with HorizontalTop Standoff Assembly Unit Assembly Prior to InstallationVenting Introduction Top Facing Support Side Nailing StripsVent terminal Air supply outlet VentRegency Direct Vent System Flex Horizontal Terminations only For Regency Direct Vent System Flex Installation ProceduresRigid Pipe Venting Systems Flat Wall InstallationMax. Wall Vent Length Thickness inches Required inchesRigid Pipe Venting Components List Description Simpson Dura-Vent SelkirkDirect VentGS R Direct-Temp TM Propane & Natural Gas Rigid Pipe Venting Arrangements Vertical TerminationsInstallation Regency Direct Vent System Flex Rigid Pipe Venting Arrangements Horizontal TerminationsHorizontal Venting with Two 2 90o Elbows Horizontal Venting with Three 3 90o ElbowsOption + H1 Option + V1 H + H1 Vertical Venting with Two 2 90o ElbowsOption + V1 With these options, max. totalVertical Venting with Three 3 90o Elbows Required Parts Vertical Termination With CO-LINEAR Flex SystemDescription Alternate Approved CapsInstallation Horizontal Installations Below Grade Snorkel InstallationSnorkel Terminations Vertical Termination GAS Line InstallationGAS Pipe Pressure Testing Pilot AdjustmentHigh Elevation T. Valve DescriptionConversion Kit Contains Optional Brick Panels LOG SET InstallationNotch BracketBracketOptional Flush Trim Standard Flush DoorCutout 5th Grate TabDouble Screen Door Flush LouversOptional BAY Door Bay louvers Must be used With the Bay glass optionFlush Louver Top Heat Shield BAY LouversBay Louver Top Heat Shield Burner ON/OFF Control boxFull Screen Front Cut-Out Oblong Hole Top Flange BottomCut-Outs Top Grill Hinge Location Bottom GrillThermostat Wire Table Optional Wall SwitchDo not cut the ground terminal off under any circumstances Wiring DiagramShut the power off Installing the Optional FANDiagram Secure left side with 2 screws Secure the 2 boxes together With one screwCopy of the Lighting Plate Instructions Operating InstructionsShutdown Procedure Lighting ProcedureAeration Adjustment Operating InstructionsMaintenance Instructions MaintenanceLOG Replacement Normal Operating Sounds GAS AppliancesThermopile Thermocouple Flush Glass ReplacementGlass Gasket Door GlassDiagram 3 Lift out Valve Tray Assembly Installing ValveRemoving Valve Shut off the gas supplyDescription Parts ListParts List Part Description Burner & Log AssemblyFlush Front & Louvers Bay Front & Louvers Regency P33-3 Zero Clearance Direct Vent Gas Fireplace Conditions WarrantyInstaller Please complete the following information