Regency P33-NG3, P33-LP3 Installation, Save These Instructions, Before YOU Start

Page 5

INSTALLATION

IMPORTANT:

SAVE THESE

INSTRUCTIONS

The P33-NG3 or P33-LP3 Direct Vent Fireplace must be installed in accordance with these in- structions. Carefully read all the instructions in this manual fi rst. Consult the "authority having jurisdiction" to determine the need for a permit prior to starting the installation. It is the respon- sibility of the installer to ensure this fi replace is installed in compliance with manufacturer's instructions and all applicable codes.

BEFORE YOU START

Safe installation and operation of this appli- ance requires common sense, however, we are required by the Canadian Safety Standards and ANSI Standards to make you aware of the

INSTALLATION AND REPAIR SHOULD BE DONE BY A QUALI- FIED SERVICE PERSON. THE APPLIANCE SHOULD BE IN- SPECTED BEFORE USE AND AT LEASTANNUALLYBYAPROFES- SIONALSERVICEPERSON.MORE FREQUENT CLEANING MAY BE REQUIRED DUE TO EXCES- SIVE LINT FROM CARPETING, BEDDING MATERIAL, ETC. IT IS IMPERATIVE THAT CONTROL COMPARTMENTS, BURNERS AND CIRCULATING AIR PAS- SAGEWAYS OF THE APPLIANCE BE KEPT CLEAN.

YOUNG CHILDREN SHOULD BE CAREFULLY SUPERVISEDWHEN THEY ARE IN THE SAME ROOM AS THE APPLIANCE.

CLOTHING OR OTHER FLAM- MABLE MATERIAL SHOULD NOT BE PLACED ON OR NEAR THE APPLIANCE.

GENERAL SAFETY

INFORMATION

1)Theapplianceinstallationmustconformwith local codes or, in the absence of local codes, with the current Canadian or National Gas Codes, CAN1-B149 or ANSI Z223.1 Installation Codes.

2)The appliance when installed, must be electrically grounded in accordance with local codes, or in the absence of local codes with the current National Electrical Code, ANSI/NFPA 70 or CSA C22.1 Canadian Electrical Code.

3)See general construction and assembly instructions. The appliance and vent should be enclosed.

4)This appliance must be connected to the specifi ed vent and termination cap to the outside of the building envelope. Never vent to another room or inside a building. Make sure that the vent is fi tted as per Venting instructions.

10)Be aware of electrical wiring locations in walls and ceilings when cutting holes for termination.

11)Under no circumstances should this ap- pliance be modifi ed. Parts that have to be removed for servicing should be replaced prior to operating this appliance.

12)Installationandanyrepairstothisappliance should be done by a qualifi ed service per- son. A professional service person should be called to inspect this appliance annually. Make it a practice to have all of your gas appliances checked annually.

13)Do not slam shut or strike the glass door.

14)Under no circumstances should any solid fuels (wood, paper, cardboard, coal, etc.) be used in this appliance.

15)The appliance area must be kept clear and free of combustible materials, (gases and other fl ammable vapours and liquids).

Emissions from burning wood or gas could contain chemicals known to the State of Cali- fornia to cause cancer, birth defects or other reproductive harm.

MANUFACTURED

MOBILE HOME

ADDITIONAL

REQUIREMENTS

DUE TO HIGH TEMPERATURES, THE APPLIANCE SHOULD BE LOCATED OUT OF TRAFFIC AND AWAY FROM FURNITURE AND DRAPERIES.

WARNING: FAILURE TO INSTALL THIS APPLIANCE CORRECTLY WILL VOID YOUR WARRANTY AND MAY CAUSE A SERIOUS HOUSE FIRE.

CHILDRENANDADULTSSHOULD BE ALERTED TO THE HAZARDS OF HIGH SURFACE TEMPERA- TURES, ESPECIALLY THE FIRE- PLACE GLASS, AND SHOULD STAYAWAY TO AVOID BURNS OR CLOTHING IGNITION.

5)Inspect the venting system annually for blockage and any signs of deterioration.

6)Venting terminals shall not be recessed into a wall or siding.

7)Any safety glass removed for servicing must be replaced prior to operating the appliance.

8)To prevent injury, do not allow anyone who is unfamiliar with the operation to use the fi replace.

9)Wear gloves and safety glasses for protec- tion while doing required maintenance.

1)Ensure that structural members are not cut or weakened during installation.

2)Ensure proper grounding using the #8 ground lug provided. See page 34.

Regency P33-3 Zero Clearance Direct Vent Gas Fireplace

Image 5
Contents P33-3 Zero Clearance To the New Owner Information for MOBILE/MANUFACTURED Homes After First SaleTable of Contents Safety Label General Safety Information InstallationSave These Instructions Before YOU StartUnit Dimensions Installation ChecklistLocating Your GAS Stove Duct System OptionMantel LEG Clearances Clearancescombustible MantelsClearances are not adhered to Fire hazard is an extreme risk if theseRear Termination Framing and FinishingSimpson Dura-Vent Minimum Clearances Vertical Termination or Vertical Rise with HorizontalTop Standoff Assembly Unit Assembly Prior to InstallationVenting Introduction Top Facing Support Side Nailing StripsVent terminal Air supply outlet VentRegency Direct Vent System Flex Horizontal Terminations only For Regency Direct Vent System Flex Installation ProceduresRigid Pipe Venting Systems Flat Wall InstallationMax. Wall Vent Length Thickness inches Required inchesDirect VentGS R Direct-Temp TM Rigid Pipe Venting Components ListDescription Simpson Dura-Vent Selkirk Propane & Natural Gas Rigid Pipe Venting Arrangements Vertical TerminationsInstallation Regency Direct Vent System Flex Rigid Pipe Venting Arrangements Horizontal TerminationsOption + H1 Horizontal Venting with Two 2 90o ElbowsHorizontal Venting with Three 3 90o Elbows Option + V1 H + H1 Vertical Venting with Two 2 90o ElbowsOption + V1 With these options, max. totalVertical Venting with Three 3 90o Elbows Required Parts Vertical Termination With CO-LINEAR Flex SystemDescription Alternate Approved CapsInstallation Snorkel Terminations Horizontal InstallationsBelow Grade Snorkel Installation Vertical Termination GAS Line InstallationGAS Pipe Pressure Testing Pilot AdjustmentHigh Elevation T. Valve DescriptionConversion Kit Contains Optional Brick Panels LOG SET InstallationNotch BracketBracketOptional Flush Trim Standard Flush DoorCutout 5th Grate TabDouble Screen Door Flush LouversOptional BAY Door Bay louvers Must be used With the Bay glass optionFlush Louver Top Heat Shield BAY LouversBay Louver Top Heat Shield Burner ON/OFF Control boxCut-Outs Full Screen FrontCut-Out Oblong Hole Top Flange Bottom Top Grill Hinge Location Bottom GrillThermostat Wire Table Optional Wall SwitchDo not cut the ground terminal off under any circumstances Wiring DiagramShut the power off Installing the Optional FANDiagram Secure left side with 2 screws Secure the 2 boxes together With one screwCopy of the Lighting Plate Instructions Operating InstructionsShutdown Procedure Lighting ProcedureAeration Adjustment Operating InstructionsMaintenance Instructions MaintenanceLOG Replacement Normal Operating Sounds GAS AppliancesThermopile Thermocouple Flush Glass ReplacementGlass Gasket Door GlassDiagram 3 Lift out Valve Tray Assembly Installing ValveRemoving Valve Shut off the gas supplyDescription Parts ListParts List Part Description Burner & Log AssemblyFlush Front & Louvers Bay Front & Louvers Regency P33-3 Zero Clearance Direct Vent Gas Fireplace Conditions WarrantyInstaller Please complete the following information