Regency P33-LP3 Framing and Finishing, Rear Termination, Simpson Dura-Vent Minimum Clearances

Page 8

INSTALLATION

FRAMING AND FINISHING

1)Determine the total thickness of facing material (e.g. drywall plus ceramic tiles) to allow the fi nished surface to be fl ush with the front of the unit. Total facing thickness can vary from 1/2" (13mm) to 1-1/4" (32mm) thick.

Rear Termination

Simpson Dura-Vent Piping

Simpson Dura-Vent Minimum Clearances

Top Header

Install Side Nailing Strips, and Top Facing Supportbeforeunitisslippedintoposition. See page 9 for assembly details.

Flex Piping

1/2"

(13mm)

Drywall

1-1/2"

(38mm)

10" (254mm) dia. Hole through wall for Dura-Vent

30”

(762mm)

2)Frame in the enclosure for the unit with framing material.

Vertical Termination or

Vertical Rise with Horizontal

Termination

For Both Simpson & Flex

NOTE: If this is an outside corner, the minimum distance between the vent and the outside corner is 6" (15cm) with AstroCap termination cap or 12" (30cm) with Dura-Vent termination cap.

For Both Simpson & Flex

NOTE: If this is an outside corner, the minimum distance between the vent and the outside corner is 6" (15cm) withAstroCap termination cap or 12" (30cm) with Dura-Vent termination cap.

3)For exterior walls, insulate the enclosure to the same degree as the rest of the house, apply vapour barrier and drywall, as per lo- cal installation codes. (Do not insulate the fireplace itself.)

4)The top of the unit must not be closer than 30" (762mm) to the ceiling.

5)Combustible material may be brought up to the top and sides of the unit and be covered with ceramic tiles, bricks, rock or other suit- able combustible fi nishing materials.

Note: Theunitdoesnothavetobecomplete- ly enclosed in a chase. The clearance on top of the unit is 0" to the standoffs socombustiblebuildingmaterialscan be laid directly on top of the standoffs. You must maintain clearance from the vent to combustible materials for flex for Simpson Dura-Vent, see page 7.

4"

3"

16-1/2”

 

(102mm)(76mm)

(419mm)

 

Opening for gas

Minimum

 

connection

 

 

 

Flex Pipe

 

Minimum Clearances

 

 

Top Header

 

1/2"

 

10" (254mm)

 

 

dia. Hole through

(13mm)

 

Drywall

 

wall for Flex

 

1-1/2"

 

26”

(660mm)

(38mm)

 

 

 

 

4"

3"

12-3/4”

 

(102mm)(76mm)

(324mm)

 

Opening for gas

Minimum

 

connection

 

 

6)Use steel studs for framing where the

1-1/2" (38mm) clearance from the vent to combustible material cannot be main- tained.

TheHeatWaveDuctKithasdifferentclear- ance and framing requirements, check the HeatWave manual for details.

Regency P33-3 Zero Clearance Direct Vent Gas Fireplace

Page 7 Page 9
Image 8
Page 7 Page 9
Contents P33-3 Zero Clearance Information for MOBILE/MANUFACTURED Homes After First Sale To the New OwnerTable of Contents Safety Label Installation General Safety InformationSave These Instructions Before YOU StartInstallation Checklist Unit DimensionsLocating Your GAS Stove Duct System OptionClearancescombustible Mantels Mantel LEG ClearancesClearances are not adhered to Fire hazard is an extreme risk if theseFraming and Finishing Rear TerminationSimpson Dura-Vent Minimum Clearances Vertical Termination or Vertical Rise with HorizontalUnit Assembly Prior to Installation Top Standoff AssemblyVenting Introduction Top Facing Support Side Nailing StripsVent Vent terminal Air supply outletRegency Direct Vent System Flex Horizontal Terminations only Installation Procedures For Regency Direct Vent System FlexFlat Wall Installation Rigid Pipe Venting SystemsMax. Wall Vent Length Thickness inches Required inchesDirect VentGS R Direct-Temp TM Rigid Pipe Venting Components ListDescription Simpson Dura-Vent Selkirk Rigid Pipe Venting Arrangements Vertical Terminations Propane & Natural GasInstallation Rigid Pipe Venting Arrangements Horizontal Terminations Regency Direct Vent System FlexOption + H1 Horizontal Venting with Two 2 90o ElbowsHorizontal Venting with Three 3 90o Elbows Vertical Venting with Two 2 90o Elbows Option + V1 H + H1Option + V1 With these options, max. totalVertical Venting with Three 3 90o Elbows Vertical Termination With CO-LINEAR Flex System Required PartsDescription Alternate Approved CapsInstallation Snorkel Terminations Horizontal InstallationsBelow Grade Snorkel Installation GAS Line Installation Vertical TerminationPilot Adjustment GAS Pipe Pressure TestingHigh Elevation T. Valve DescriptionConversion Kit Contains LOG SET Installation Optional Brick PanelsNotch BracketBracketStandard Flush Door Optional Flush TrimCutout 5th Grate TabFlush Louvers Double Screen DoorOptional BAY Door Bay louvers Must be used With the Bay glass optionBAY Louvers Flush Louver Top Heat ShieldBay Louver Top Heat Shield Burner ON/OFF Control boxCut-Outs Full Screen FrontCut-Out Oblong Hole Top Flange Bottom Hinge Location Bottom Grill Top GrillOptional Wall Switch Thermostat Wire TableWiring Diagram Do not cut the ground terminal off under any circumstancesInstalling the Optional FAN Shut the power offDiagram Secure left side with 2 screws Secure the 2 boxes together With one screwOperating Instructions Copy of the Lighting Plate InstructionsLighting Procedure Shutdown ProcedureAeration Adjustment Operating InstructionsMaintenance Maintenance InstructionsLOG Replacement Normal Operating Sounds GAS AppliancesFlush Glass Replacement Thermopile ThermocoupleGlass Gasket Door GlassInstalling Valve Diagram 3 Lift out Valve Tray AssemblyRemoving Valve Shut off the gas supplyParts List DescriptionParts List Burner & Log Assembly Part DescriptionFlush Front & Louvers Bay Front & Louvers Regency P33-3 Zero Clearance Direct Vent Gas Fireplace Warranty ConditionsInstaller Please complete the following information
Top Page Image Contents