Regency P33-NG3 Unit Assembly Prior to Installation, Venting Introduction, Top Standoff Assembly

Page 9

INSTALLATION

UNIT ASSEMBLY

PRIOR TO INSTALLATION

The Top Facing Support, the Side Nailing Strips and the 2 Top Standoffs must be correctly po- sitioned and attached to the top before the unit is put into position.

Top Standoff Assembly

The top standoffs are shipped in a fl at position and must be pulled up and bent into the cor- rect shape.

1)Remove the standoffs from on top of the fi rebox by undoing the screws.

2)Take each standoff and bend into the cor- rect shape. Bend up at the bend lines until the screw holes in the standoff and the pre-punched screw holes on the fi rebox top line-up.

3)Attach the standoffs securely to the top with 4 screws per standoff.

Note: Secure the standoffs to the holes closest to the edge of the fi rebox top.

Top Facing Support &

Side Nailing Strips

Determine the total thickness of facing mate- rial (e.g. drywall plus ceramic tiles) to allow the

finished surface to be fl ush with the front of the unit. Total facing thickness can vary from 1/2" (13mm) to 1-1/4" (32mm) thick.

The Top Facing Support & Side Nailing Strips can be mounted in various positions depending on the thickness of the facing material.

1)Mount Top Facing Support using the 3 supplied screws into the three pre-punched screw holes on the top front of the unit.Adjust support to desired facing material depth.

2)Mount Side Nailing Strip using the 3 sup- plied screws into the three pre-punched screw holes at the front sides of the unit. Adjust support to desired facing material thickness.

For a facing material depth of 1-1/4"(32mm), the top facing support must be reversed.

VENTING INTRODUCTION

The P33-3 uses the "balanced fl ue" technology Co Axial system. The inner liner vents products of combustion to the outside while the outer liner draws outside combustion air into the combustion chamber thereby eliminating the need to use heated room air for combustion and losing warm room air up the chimney.

There are 2 vent systems approved for use with the P33-3: the Regency Direct Vent System (Flex) for Horizontal Terminations only (see pages 11-12), and the Simpson Dura-Vent Systems for Horizontal and Vertical Terminations (see pages 13-24).

Note: These flue pipes must not be connected to any other appliance.

The gas appliance and vent system must be vented directly to the outside of the building, and never be attached to a chimney serving a separate solid fuel or gas burning appliance. Each direct vent gas appliance must use it's own separate vent system. Common vent systems are prohibited.

NOTE: Ensure compliance with the outside vent terminal location before cutting hole as both dimensions must be met.

Regency P33-3 Zero Clearance Direct Vent Gas Fireplace

Page 8 Page 10
Image 9
Page 8 Page 10
Contents P33-3 Zero Clearance To the New Owner Information for MOBILE/MANUFACTURED Homes After First SaleTable of Contents Safety Label General Safety Information InstallationSave These Instructions Before YOU StartUnit Dimensions Installation ChecklistLocating Your GAS Stove Duct System OptionMantel LEG Clearances Clearancescombustible MantelsClearances are not adhered to Fire hazard is an extreme risk if theseRear Termination Framing and FinishingSimpson Dura-Vent Minimum Clearances Vertical Termination or Vertical Rise with HorizontalTop Standoff Assembly Unit Assembly Prior to InstallationVenting Introduction Top Facing Support Side Nailing StripsVent terminal Air supply outlet VentRegency Direct Vent System Flex Horizontal Terminations only For Regency Direct Vent System Flex Installation ProceduresRigid Pipe Venting Systems Flat Wall InstallationMax. Wall Vent Length Thickness inches Required inchesRigid Pipe Venting Components List Description Simpson Dura-Vent SelkirkDirect VentGS R Direct-Temp TM Propane & Natural Gas Rigid Pipe Venting Arrangements Vertical TerminationsInstallation Regency Direct Vent System Flex Rigid Pipe Venting Arrangements Horizontal TerminationsHorizontal Venting with Two 2 90o Elbows Horizontal Venting with Three 3 90o ElbowsOption + H1 Option + V1 H + H1 Vertical Venting with Two 2 90o ElbowsOption + V1 With these options, max. totalVertical Venting with Three 3 90o Elbows Required Parts Vertical Termination With CO-LINEAR Flex SystemDescription Alternate Approved CapsInstallation Horizontal Installations Below Grade Snorkel InstallationSnorkel Terminations Vertical Termination GAS Line InstallationGAS Pipe Pressure Testing Pilot AdjustmentHigh Elevation T. Valve DescriptionConversion Kit Contains Optional Brick Panels LOG SET InstallationNotch BracketBracketOptional Flush Trim Standard Flush DoorCutout 5th Grate TabDouble Screen Door Flush LouversOptional BAY Door Bay louvers Must be used With the Bay glass optionFlush Louver Top Heat Shield BAY LouversBay Louver Top Heat Shield Burner ON/OFF Control boxFull Screen Front Cut-Out Oblong Hole Top Flange BottomCut-Outs Top Grill Hinge Location Bottom GrillThermostat Wire Table Optional Wall SwitchDo not cut the ground terminal off under any circumstances Wiring DiagramShut the power off Installing the Optional FANDiagram Secure left side with 2 screws Secure the 2 boxes together With one screwCopy of the Lighting Plate Instructions Operating InstructionsShutdown Procedure Lighting ProcedureAeration Adjustment Operating InstructionsMaintenance Instructions MaintenanceLOG Replacement Normal Operating Sounds GAS AppliancesThermopile Thermocouple Flush Glass ReplacementGlass Gasket Door GlassDiagram 3 Lift out Valve Tray Assembly Installing ValveRemoving Valve Shut off the gas supplyDescription Parts ListParts List Part Description Burner & Log AssemblyFlush Front & Louvers Bay Front & Louvers Regency P33-3 Zero Clearance Direct Vent Gas Fireplace Conditions WarrantyInstaller Please complete the following information
Top Page Image Contents