Regency G36D installation manual Venting

Page 11

INSTALLATION

VENTING

UltraGlow® Direct Vent System (Flex)

Horizontal Terminations Only

These venting systems, in combination with the G36D Direct Vent Gas Fireplace, have been tested and listed as a direct vent heater system by Warnock Hersey. The location of the termination cap must conform to the requirements in the Vent Terminal Locations diagram in the "Exterior Vent Termination Locations" section.

UltraGlow® Direct Vent Flex Termination Kit (Part # 946-515) includes all the parts needed to install the G36D with a maximum total run of 4 feet.

1)6-7/8" dia. ﬂ exible liner (4 ft. length)

2)4" dia. ﬂ exible liner (4 ft. length)

3)spring spacers (4)

4)thimble (2)

5)AstroCap termination cap (1)

6) screws (12)

7)tube of Mill Pac (1)

8) plated screws (8)

9)screws #8 x 1-1/2" Drill Point, Stainless Steel (4)

Notes:

1)Liner sections should be continuous without any joints or seams.

2)Only Flex pipe purchased from Regency® may be used for Flex installations.

UltraGlow® G36D Zero Clearance Direct Vent Gas Fireplace

11

Image 11

Contents 12/18/05 G36D Zero Clearance Direct Vent Gas FireplaceTo the New Owner Information for MOBILE/MANUFACTURED Homes After First SaleTable of Contents Certified for/Certifiée pour Canada and U.S.A Safety LabelCopy of Safety Decal for G36D-NG1 300Before YOU Start InstallationInstallation Checklist Important Message Save These InstructionsManufactured Mobile Home Additional Requirements G36D Unit DimensionsDiagram Locating Your GAS StoveFraming Finishing ClearancesMantel LEG Clearances Combustible Mantels Top Facing Support Side Nailing Strips Unit Assembly Prior to InstallationTop Standoff Assembly Venting IntroductionVertical Termination Area where terminal is not permitedExterior Vent LocationsVenting Secure Vent Rigid Pipe Venting Components ListAlternate Rigid Pipe Venting SystemsUltraGlow Direct Vent System Flex Rigid Pipe Venting Arrangements Horizontal TerminationsInstallation Rigid Pipe Venting Arrangements Vertical Terminations Installation Flex Liner Vertical Termination With CO-LINEAR Flex SystemRequired Parts DescriptionVenting Arrangements Vertical Terminations Snorkel Terminations Diagram 3aI g h t Achieved Continue to assemble pipe lengths Firestop spacer must be installedDiagram Roof Pitch Ceiling to the positionFor UltraGlow Direct Vent System Flex Installation ProceduresOffset Chart High Elevation Pilot AdjustmentGAS Line Installation GAS Pipe Pressure TestingDC Sparker Kit Contains Qty Installation of LPG Conversion KitLPG Conversion Kit Contains QtyPiezo Ignitor Ignitor WireSparker Ignitor Wire Ground Wire from KitChain Install the 1/2 bushing to the heat shieldHeat Shield 02-53 02-51 02-54 LOG SET Installation02-75 02-55 02-52 Front Brackets 5th Grate TabLog indentation Rear Grate TabPlace embers in these 3 locations On the burner tray Install ﬂ ush glass as per instructions in manualOptional Flush Trim Standard Flush DoorFlush Louvers Wall Thermostat Remote ControlWall Switch Thermostat Wire TableDo not cut the ground terminal off under any circumstances Wiring DiagramOpen the bottom louver door Installing the Optional FANTo Remove the Fan Operating Instructions Normal Operating Sounds of GAS Appliances Maintenance InstructionsCopy of the Lighting Plate Instructions Maintenance Removing Valve Installing ValveG36D Main Assembly Pilot Assembly Gasket Parts ListG36D Flush Front Assembly UltraGlow G36D Zero Clearance Direct Vent Gas Fireplace UltraGlow G36D Zero Clearance Direct Vent Gas Fireplace Exclusions WarrantyConditions Register your UltraGlow online at