Regency G36D 5th Grate Tab, Log indentation, Rear Grate Tab, Front Brackets, Rear Bracket Cutouts

Page 28

INSTALLATION

6)Position Log 02-54 across the cutouts in Logs 02-51 and 02-53. The notch in the bottom right end ﬁ tting against the 5th grate tab.

02-54

02-51

02-54

5th Grate Tab

7)Place the bottom left front edge of Log 02-55 against the rear bracket on the burner tray and rest the log on the cutout on Log 02-53.

8)Place Log 02-52 between Logs 02-51 and 02-75 and on the indentation on Log 02-54. The bottom right end sits behind the rear grate tab.

02-75

02-52

02-51

02-54

Log indentation

Photo shows rear grate tab. Log 02-51 was removed to show the positioning of Log 02-52.

Rear

Grate Tab

9)Sit Log 02-50 on the front left side of the burner. Push the back of the log against the 2 front brackets with the notch on the bottom of the log ﬁ tting into the ﬁ rst grate tab.

02-75

02-55

02-51

Front Brackets

02-55

Rear Bracket

Cutouts

02-50

Notch

28	UltraGlow® G36D Zero Clearance Direct Vent Gas Fireplace

Image 28

Contents G36D Zero Clearance Direct Vent Gas Fireplace 12/18/05Information for MOBILE/MANUFACTURED Homes After First Sale To the New OwnerTable of Contents Safety Label Copy of Safety Decal for G36D-NG1300 Certified for/Certifiée pour Canada and U.S.AInstallation Installation ChecklistImportant Message Save These Instructions Before YOU StartG36D Unit Dimensions DiagramLocating Your GAS Stove Manufactured Mobile Home Additional RequirementsMantel LEG Clearances ClearancesFraming Finishing Combustible Mantels Unit Assembly Prior to Installation Top Standoff AssemblyVenting Introduction Top Facing Support Side Nailing StripsArea where terminal is not permited Exterior VentLocations Vertical TerminationVenting Rigid Pipe Venting Components List Secure VentRigid Pipe Venting Systems AlternateRigid Pipe Venting Arrangements Horizontal Terminations UltraGlow Direct Vent System FlexInstallation Rigid Pipe Venting Arrangements Vertical Terminations Installation Vertical Termination With CO-LINEAR Flex System Required PartsDescription Flex LinerVenting Arrangements Vertical Terminations I g h t Achieved Diagram 3aSnorkel Terminations Firestop spacer must be installed Diagram Roof PitchCeiling to the position Continue to assemble pipe lengthsOffset Chart Installation ProceduresFor UltraGlow Direct Vent System Flex Pilot Adjustment GAS Line InstallationGAS Pipe Pressure Testing High ElevationInstallation of LPG Conversion Kit LPG Conversion Kit ContainsQty DC Sparker Kit Contains QtyIgnitor Wire Sparker Ignitor WireGround Wire from Kit Piezo IgnitorHeat Shield Install the 1/2 bushing to the heat shieldChain 02-75 02-55 02-52 LOG SET Installation02-53 02-51 02-54 5th Grate Tab Log indentationRear Grate Tab Front BracketsInstall ﬂ ush glass as per instructions in manual Place embers in these 3 locations On the burner trayFlush Louvers Standard Flush DoorOptional Flush Trim Remote Control Wall SwitchThermostat Wire Table Wall ThermostatWiring Diagram Do not cut the ground terminal off under any circumstancesTo Remove the Fan Installing the Optional FANOpen the bottom louver door Operating Instructions Copy of the Lighting Plate Instructions Maintenance InstructionsNormal Operating Sounds of GAS Appliances Maintenance Installing Valve Removing ValveG36D Main Assembly Parts List Pilot Assembly GasketG36D Flush Front Assembly UltraGlow G36D Zero Clearance Direct Vent Gas Fireplace UltraGlow G36D Zero Clearance Direct Vent Gas Fireplace Conditions WarrantyExclusions Register your UltraGlow online at