Regency G36D installation manual Standard Flush Door, Flush Louvers, Optional Flush Trim

Page 30

INSTALLATION

STANDARD FLUSH

DOOR

The standard ﬂush door comes with a black frame. To install the frame, simply hook the top door ﬂ ange onto the top of the unit and swing the door towards the unit, diagram 1.

Use the hook to pull the spring out until you can put the hook into the slot on the bottom door bracket. Repeat for 2nd spring. See diagram 3.

Flush Louvers

1)	Install each top by clipping the louver lip
	onto the top louver brackets ensuring that
	each individual louver is centered from side
	to side.
2)	The bottom louver has a hinge that is
	attached (2 screws per hinge) to the lip on
	bottom of the unit.
3)	Open the bottom louver. Pull the Burner
	ON/OFF control box from inside the bottom
	of the ﬁ replace and position the slots in the

Diagram 3

To remove the ﬂ ush door, reverse the above steps.

Optional Flush Trim

bracket over the 2 screws on the left side

of the bottom louver. Push down to lock into

place. Tighten the screws.

Attach the round magnets to the back of the

Diagram 1 top trim piece and to the bottom trim piece, then attach trim to the top and bottom of Flush

door.

Note: Top and bottom louvers are different.

Be careful that the glass gasket does not roll up; there must be a gap between the gasket and the door lip to ensure that the door sits securely on the unit. Diagram 2.

Diagram 2

30	UltraGlow® G36D Zero Clearance Direct Vent Gas Fireplace

Image 30

Contents G36D Zero Clearance Direct Vent Gas Fireplace 12/18/05Information for MOBILE/MANUFACTURED Homes After First Sale To the New OwnerTable of Contents 300 Safety LabelCopy of Safety Decal for G36D-NG1 Certified for/Certifiée pour Canada and U.S.AImportant Message Save These Instructions InstallationInstallation Checklist Before YOU StartLocating Your GAS Stove G36D Unit DimensionsDiagram Manufactured Mobile Home Additional RequirementsClearances Mantel LEG ClearancesFraming Finishing Combustible Mantels Venting Introduction Unit Assembly Prior to InstallationTop Standoff Assembly Top Facing Support Side Nailing StripsLocations Area where terminal is not permitedExterior Vent Vertical TerminationVenting Rigid Pipe Venting Components List Secure VentRigid Pipe Venting Systems AlternateRigid Pipe Venting Arrangements Horizontal Terminations UltraGlow Direct Vent System FlexInstallation Rigid Pipe Venting Arrangements Vertical Terminations Installation Description Vertical Termination With CO-LINEAR Flex SystemRequired Parts Flex LinerVenting Arrangements Vertical Terminations Diagram 3a I g h t AchievedSnorkel Terminations Ceiling to the position Firestop spacer must be installedDiagram Roof Pitch Continue to assemble pipe lengthsInstallation Procedures Offset ChartFor UltraGlow Direct Vent System Flex GAS Pipe Pressure Testing Pilot AdjustmentGAS Line Installation High ElevationQty Installation of LPG Conversion KitLPG Conversion Kit Contains DC Sparker Kit Contains QtyGround Wire from Kit Ignitor WireSparker Ignitor Wire Piezo IgnitorInstall the 1/2 bushing to the heat shield Heat ShieldChain LOG SET Installation 02-75 02-55 02-5202-53 02-51 02-54 Rear Grate Tab 5th Grate TabLog indentation Front BracketsInstall ﬂ ush glass as per instructions in manual Place embers in these 3 locations On the burner trayStandard Flush Door Flush LouversOptional Flush Trim Thermostat Wire Table Remote ControlWall Switch Wall ThermostatWiring Diagram Do not cut the ground terminal off under any circumstancesInstalling the Optional FAN To Remove the FanOpen the bottom louver door Operating Instructions Maintenance Instructions Copy of the Lighting Plate InstructionsNormal Operating Sounds of GAS Appliances Maintenance Installing Valve Removing ValveG36D Main Assembly Parts List Pilot Assembly GasketG36D Flush Front Assembly UltraGlow G36D Zero Clearance Direct Vent Gas Fireplace UltraGlow G36D Zero Clearance Direct Vent Gas Fireplace Warranty ConditionsExclusions Register your UltraGlow online at