Regency G36D Locating Your GAS Stove, Manufactured Mobile Home Additional Requirements, Diagram

Page 6

INSTALLATION

This includes:

1)Clocking the appliance to ensure the correct fi ring rate (rate noted on label 26,000 Btu/h) after burning appliance for 15 minutes.

2)If required, adjusting the primary air to ensure that the fl ame does not carbon. First allow the unit to burn for 15-20 min. to stabilize.

CAUTION: Any alteration to the product that causes sooting or carboning that results in damage is not the responsibility of the manufacturer.

LOCATING YOUR

GAS STOVE

5)This appliance is Listed for bedroom installations when used with a Listed Millivolt Thermostat. Some areas may have further requirements, check local codes before installation.

6)The G36D Direct Vent Gas Fireplace is approved for alcove installations, which meet the clearances listed on this page.

7)Werecommendthatyouplanyourinstallation on paper using exact measurements for clearances and floor protection before actually installing this appliance. Have a qualifi ed inspector, dealer, or installer review your plans before installation.

Note: For vent terminations see the "ExteriorVentTerminationLocations" section.

MANUFACTURED

MOBILE HOME

ADDITIONAL

REQUIREMENTS

1)Ensure that structural members are not cut or weakened during installation.

2)Ensure proper grounding using the #8 ground lug provided. Refer to the "Wiring Diagram" section.

1)When selecting a location for your fi replace, ensure that the clearances outlined on this page are met.

2)Provide adequate clearances for servicing.

3)The appliance must be installed on a fl at, solid, continuous surface (e.g. wood, metal, concrete). This may be the fl oor, or raised up on a platform to enhance its visual impact. If the appliance is going to be installed on carpeting, combustible linoleum tile or other combustible material other than wood

flooring, the appliance must be installed on a metal or wood panel extending the full width and depth of the appliance.

4)The G36D Direct Vent Gas Fireplace can be installed in a recessed position or framed out into the room as in A, B, C, D. See Diagram 1.

A)Flat on Wall

B)Flat on Wall Corner

C)Recessed into Wall/Alcove

D)Corner

Diagram 1

G36D UNIT DIMENSIONS

6

UltraGlow® G36D Zero Clearance Direct Vent Gas Fireplace

Page 5 Page 7
Image 6
Page 5 Page 7
Contents G36D Zero Clearance Direct Vent Gas Fireplace 12/18/05Information for MOBILE/MANUFACTURED Homes After First Sale To the New OwnerTable of Contents 300 Safety LabelCopy of Safety Decal for G36D-NG1 Certified for/Certifiée pour Canada and U.S.AImportant Message Save These Instructions InstallationInstallation Checklist Before YOU StartLocating Your GAS Stove G36D Unit DimensionsDiagram Manufactured Mobile Home Additional RequirementsClearances Mantel LEG ClearancesFraming Finishing Combustible Mantels Venting Introduction Unit Assembly Prior to InstallationTop Standoff Assembly Top Facing Support Side Nailing StripsLocations Area where terminal is not permitedExterior Vent Vertical TerminationVenting Rigid Pipe Venting Components List Secure VentRigid Pipe Venting Systems AlternateRigid Pipe Venting Arrangements Horizontal Terminations UltraGlow Direct Vent System FlexInstallation Rigid Pipe Venting Arrangements Vertical Terminations Installation Description Vertical Termination With CO-LINEAR Flex SystemRequired Parts Flex LinerVenting Arrangements Vertical Terminations Diagram 3a I g h t AchievedSnorkel Terminations Ceiling to the position Firestop spacer must be installedDiagram Roof Pitch Continue to assemble pipe lengthsInstallation Procedures Offset ChartFor UltraGlow Direct Vent System Flex GAS Pipe Pressure Testing Pilot AdjustmentGAS Line Installation High ElevationQty Installation of LPG Conversion KitLPG Conversion Kit Contains DC Sparker Kit Contains QtyGround Wire from Kit Ignitor WireSparker Ignitor Wire Piezo IgnitorInstall the 1/2 bushing to the heat shield Heat ShieldChain LOG SET Installation 02-75 02-55 02-5202-53 02-51 02-54 Rear Grate Tab 5th Grate TabLog indentation Front BracketsInstall fl ush glass as per instructions in manual Place embers in these 3 locations On the burner trayStandard Flush Door Flush LouversOptional Flush Trim Thermostat Wire Table Remote ControlWall Switch Wall ThermostatWiring Diagram Do not cut the ground terminal off under any circumstancesInstalling the Optional FAN To Remove the FanOpen the bottom louver door Operating Instructions Maintenance Instructions Copy of the Lighting Plate InstructionsNormal Operating Sounds of GAS Appliances Maintenance Installing Valve Removing ValveG36D Main Assembly Parts List Pilot Assembly GasketG36D Flush Front Assembly UltraGlow G36D Zero Clearance Direct Vent Gas Fireplace UltraGlow G36D Zero Clearance Direct Vent Gas Fireplace Warranty ConditionsExclusions Register your UltraGlow online at
Top Page Image Contents