Nilfisk-Advance America SR 1100S manuel dutilisation Dust Filter Cleaning and Integrity Check

Page 71

USER MANUAL

ENGLISH

DUST FILTER CLEANING AND INTEGRITY

B

C

E

CHECK

 

 

 

NOTE

 

 

 

Besides the standard paper fi lter, polyester fi lters are

A

 

 

also available. The following procedure is applicable

 

A

to each type of fi lter.

 

 

1.Drive the machine on a level ground and engage the parking brake with the pedal (3) and the lever (4).

2.

Turn the ignition key (82) to "0".

D

3.

Disengage the hook (18) by pulling its lower end.

4.Remove the hopper (17) by using the handle (19) and by disengaging it from the inner guides.

5.Unscrew the knobs (33) and remove the fi lter compartment cover (32).

6.Loosen the knobs (A, Fig. 9).

7.

Disconnect the connector (B, Fig. 9) from the fi lter shaker

S311397

 

motor (C).

 

Figure 9

8.

Remove the dust fi lter fastening frame (D, Fig. 9).

 

9.

Remove the dust fi lter (E, Fig. 9).

 

10.

In an outdoor area, clean the fi lter by shaking it on a level

A

 

and clean surface, tapping the side (A, Fig. 11) opposite to

 

 

the wire gauze (B).

 

 

Complete the cleaning procedure by using compressed air

 

 

(C, Fig. 11) at maximum 6 Bars, blowing only from the side

 

 

of the wire gauze (B), at a minimum distance of 30 cm.

 

 

Moreover, according to the fi lter type, observe the following

 

 

cautions:

 

 

• Paper fi lter (standard): Do not use water or detergents

 

 

to clean it, otherwise it can be damaged.

 

 

• Polyester fi lter (optional): For a better cleaning, it is

 

 

allowed to wash the fi lter with water and non-lathering

 

 

detergents. This provides better quality cleaning but

S311398

 

reduces the life of the fi lter, which will have to be

 

replaced more frequently. The use of inadequate

Figure 10

 

detergents can damage the fi lter.

 

11.Check the fi lter body for tears. If necessary, replace the

filter.

12.Clean the rubber gasket (A, Fig. 10) of the cover (32) and check it for integrity and effi ciency; if necessary replace it.

13.Assemble the components in the reverse order of disassembly, and note the following:

• Install the fi lter (E, Fig. 9) with the wire gauze (B, Fig.

11)facing upwards.

S311399

Figure 11

SR 1100S P

146 2559 000(2)2007-02 A

21

Page 70 Page 72
Image 71
Page 70 Page 72
Contents 146 2559 00022007-02 a Sweeper SR 1100S PSR 1100S P SweeperSR 1100S P InhaltsverzeichnisEinleitung Funktionseigenschaften Andere ReferenzanleitungenErsatzteile UND Wartung Änderungen UND Technische VerbesserungenSicherheit Benutzte SymboleAUSPACKEN/AUSLIEFERUNG Allgemeine Hinweise Deutsch Betriebsanleitung Maschinenaufbau Maschinenbeschreibung63 64 ZUBEHÖRE/OPTIONEN Schalttafel UND BedienelementeTechnische Daten Farbencodes SchaltplanSchaltplan fortgesetzt PRÜFUNG/VORBEREITUNG DER Batterien AN Einer Neuen Maschine BetriebMaschinenanlassen VOR DEM Anlassen DER MaschineMaschinenanlassen UND -ABSTELLEN Maschinenabstellen Maschine in BetriebWartung Stunden Übersichtstabelle DER Planmässigen WartungVorgang AllePrüfung UND Einstellung DER Hauptkehrwalzenhöhe Die entsprechende Nabe a eingefügt wird Ersetzen DER HauptkehrwalzeErsetzung DER Seitenbesen Prüfung UND Einstellung DER SeitenbesenhöheReinigung UND Vollständigkeitsprüfung Desb C E Staubfilters Prüfung der Vorder- und Hinterflaps Prüfung DER Flapshöhe UND FunktionsfähigkeitPrüfung der Seitenflaps Einbau PRÜFUNG/ERSETZUNG/RÜCKSCHALTUNG DER SicherungenPrüfung/Ersetzung der Flachsicherungen Prüfung der rückschaltbaren SicherungenFehler Mögliche Ursache Lösung FehlersucheVerschrottung Introduction Table DES MatieresIntroduction Capacites Operationnelles Autres Manuels DE ReferencePieces DE Rechange ET Entretien Modifications ET AmeliorationsSecurite Symboles UtilisesDeballage / Livraison Instructions Generales Français Manuel Dutilisation Structure DE LA Machine Description DE LA MachineStructure DE LA Machine suite Accessoires / Options Tableau DE Bord ET CommandesCaracteristiques Techniques Codes des couleurs Schema ElectriqueLégende Schema Electrique suite Controle / Preparation DES Batteries SUR UNE Machine Neuve UtilisationMise en marche de la machine Avant LA Mise EN MarcheMise EN Marche ET Arret DE LA Machine Arrêt de la machine Machine AU TravailEntretien Heures Plan Dentretien ProgrammeLors de la Toutes Procédure LesControle ET Reglage DE LA Hauteur DU Balai Central Remplacement DU Balai Central Controle ET Reglage DE LA Hauteur DES Balais Lateraux Remplacement DES Balais LaterauxNettoyage ET Controle DE Lintegrite DU Filtre a Poussiere Contrôle des volets avant et arrière Controle DE LA Hauteur ET DU Fonctionnement DES VoletsContrôle des volets latéraux Repose Controle / Remplacement Retablissement DES FusiblesContrôle / remplacement des fusibles à lamelle Contrôle des fusibles restaurablesProblème Cause probable Remède Depistage DES PannesMise EN Decharge Table of Contents Identification Data Manual Purpose and ContentsHOW to Keep this Manual Declaration of Conformity TargetOperation Capabilities Spare Parts and MaintenanceOther Reference Manuals Changes and ImprovementsUNPACKING/DELIVERY SafetySymbols General Instructions English Machine Structure Machine DescriptionMachine Structure Continues Control Panel ACCESSORIES/OPTIONSTechnical Data Colour code Wiring DiagramKey Wiring Diagram Continues USE Battery CHECK/SETTING on a NEW MachineStarting the machine Before Starting the MachineStarting and Stopping the Machine Stopping the machine Machine OperationMaintenance Hours Scheduled Maintenance TableEvery Procedure Upon delivery 100 200 300 400 Main Broom Height Check Adjustment Main Broom Replacement Side Broom Replacement Side Broom Height Check AdjustmentDust Filter Cleaning and Integrity Check Front and rear skirt check Skirt Height and Operation CheckSide skirt check Assembly Hood Safety Switch Operation CheckFuse CHECK/REPLACEMENT/RESET Lamellar fuse check/replacementTrouble Possible cause Remedy TroubleshootingScrapping Inleiding InhoudsopgaveInleiding Bedrijfscapaciteit Andere GebruikershandleidingenVervangingsonderdelen EN Onderhoud Modificaties EN VerbeteringenVeiligheid Gebruikte SymbolenVerpakking VERWIJDEREN/AFLEVERING Algemene Instructies Nederlands Gebruiksaanwijzing Bouw VAN DE Machine Beschrijving VAN DE MachineOpbouw VAN DE Machine vervolg Bedieningspaneel EN Knoppen Accessoires / OptiesTechnische Eigenschappen Kleurcodering Elektrisch SchemaElektrische Installatie vervolg Controle / Voorbereidingen Voor Accus OP EEN Nieuwe Machine GebruikStarten van de machine Voor HET Starten VAN DE MachineDE Machine Starten EN Stoppen De machine stoppen Machine in BedrijfOnderhoud Procedure Bij aflevering Elke OnderhoudsschemaDE Hoogte VAN DE Hoofdborstel Controleren EN Afstellen DE Hoofdborstelvervangen DE Zijborstels Vervangen DE Hoogte VAN DE Zijborstels Controleren EN AfstellenReiniging EN Contole OP Integriteit VAN HET Stoffilter Controle van de voor- en achterflap Controle VAN DE Hoogte EN Werking VAN DE FlapsControle van de zijflaps Montage Controle / Vervanging / Resetten VAN DE ZekeringenControle/vervanging van de smeltzekeringen Controle van de herbruikbare zekeringenProbleem Waarschijnlijke oorzaak Oplossing Storingen LokaliserenVerwijdering

SR 1100S specifications

The Nilfisk-Advance America SR 1100S is a robust, versatile scrubber designed to meet the diverse cleaning needs of various commercial environments. Ideal for both small and medium-sized spaces, this machine excels in performance, efficiency, and ease of use, making it an excellent choice for businesses looking to achieve a high standard of cleanliness.

One of the standout features of the SR 1100S is its compact and ergonomic design. This allows for easy maneuverability in tight spaces such as aisles, smaller retail environments, and crowded areas. The machine is equipped with a highly efficient brush system that ensures effective scrubbing while reducing water and detergent consumption, enabling operators to achieve optimal results while also being environmentally conscious.

The SR 1100S is powered by a reliable battery system that offers an impressive run time. This allows for extended cleaning sessions without the need for frequent recharging, which can be a significant advantage in busy commercial settings. Additionally, the scrubber features a simple control panel, making it user-friendly for operators of varying skill levels. The intuitive design means that staff can quickly learn to operate the machine, enhancing productivity throughout the organization.

One of the key technologies employed in the Nilfisk-Advance America SR 1100S is the advanced Ecoflex system. This innovative technology enables users to adjust the water and detergent flow according to the specific cleaning needs of each task. This not only helps in conserving resources but also ensures that surfaces are cleaned effectively, regardless of the level of soiling.

Furthermore, the SR 1100S is designed with operator safety in mind. With features that reduce noise levels during operation, it makes it suitable for use in noise-sensitive areas, such as schools and hospitals. The scrubber is also built with maintenance accessibility in mind, allowing for quick and easy servicing, which minimizes downtime.

In conclusion, the Nilfisk-Advance America SR 1100S is a powerful, efficient, and user-friendly scrubber that is backed by advanced technology. Its compact design, effective cleaning capabilities, and operator-friendly features make it a valuable addition to any cleaning fleet. With its commitment to sustainability and efficiency, the SR 1100S is an ideal choice for businesses aiming to maintain a clean and safe environment for employees and customers alike.
Top Page Image Contents