Nilfisk-Advance America SR 1100S manuel dutilisation Main Broom Height Check Adjustment

Page 68

ENGLISH

USER MANUAL

MAIN BROOM HEIGHT CHECK AND

ADJUSTMENT

NOTE

Brooms with harder or softer bristles are available. This procedure is applicable to all types of brooms.

1.Check the main broom distance from the ground, according to the following procedure:

•Drive the machine on a level fl oor.

•Keep the machine stationary, lower the main broom and turn it on for a few seconds.

•Stop and lift the main broom, then move the machine and switch it off.

•Check that the main broom print (A, Fig. 1), along its length, is 2 to 4 cm wide.

If the print (A) is not within specifi cations, adjust the broom height as shown in step 2.

2.Engage the parking brake with the pedal (3) and the lever

(4).

3.Turn the ignition key (82) to "0".

4.Open the hood (7).

5.Loosen the knob (A, Fig. 2) on the left side of the machine.

6.Turn the knob (B, Fig. 2) and remind that:

•It must be screwed to lift the broom;

•It must be unscrewed to lower the broom.

After the adjustment, hold the knob (B) and tighten the knob (A).

7.Perform step 1 again to check that the main broom is at the correct distance from the ground.

8.When the broom is too worn to be adjusted, replace it as shown in the next paragraph.

CAUTION!

If the main broom print is excessive (larger than 4 cm), the machine regular operation is affected and the moving or electrical parts can overheat, thus reducing machine life.

Pay careful attention when performing the above- mentioned checks, and always use the machine according to the indicated conditions.

S311389

Figure 1

A

B

S311390

Figure 2

18

146 2559 000(2)2007-02 A

SR 1100S P

Page 67 Page 69
Image 68
Page 67 Page 69
Contents Sweeper SR 1100S P 146 2559 00022007-02 aSweeper SR 1100S PInhaltsverzeichnis SR 1100S PEinleitung Andere Referenzanleitungen Ersatzteile UND WartungÄnderungen UND Technische Verbesserungen FunktionseigenschaftenSicherheit Benutzte SymboleAUSPACKEN/AUSLIEFERUNG Allgemeine Hinweise Deutsch Betriebsanleitung Maschinenbeschreibung Maschinenaufbau63 64 Schalttafel UND Bedienelemente ZUBEHÖRE/OPTIONENTechnische Daten Schaltplan FarbencodesSchaltplan fortgesetzt Betrieb PRÜFUNG/VORBEREITUNG DER Batterien AN Einer Neuen MaschineMaschinenanlassen VOR DEM Anlassen DER MaschineMaschinenanlassen UND -ABSTELLEN Maschine in Betrieb MaschinenabstellenWartung Übersichtstabelle DER Planmässigen Wartung VorgangAlle StundenPrüfung UND Einstellung DER Hauptkehrwalzenhöhe Ersetzen DER Hauptkehrwalze Die entsprechende Nabe a eingefügt wirdPrüfung UND Einstellung DER Seitenbesenhöhe Ersetzung DER SeitenbesenReinigung UND Vollständigkeitsprüfung Desb C E Staubfilters Prüfung der Vorder- und Hinterflaps Prüfung DER Flapshöhe UND FunktionsfähigkeitPrüfung der Seitenflaps PRÜFUNG/ERSETZUNG/RÜCKSCHALTUNG DER Sicherungen Prüfung/Ersetzung der FlachsicherungenPrüfung der rückschaltbaren Sicherungen EinbauFehler Mögliche Ursache Lösung FehlersucheVerschrottung Table DES Matieres IntroductionIntroduction Autres Manuels DE Reference Pieces DE Rechange ET EntretienModifications ET Ameliorations Capacites OperationnellesSecurite Symboles UtilisesDeballage / Livraison Instructions Generales Français Manuel Dutilisation Description DE LA Machine Structure DE LA MachineStructure DE LA Machine suite Tableau DE Bord ET Commandes Accessoires / OptionsCaracteristiques Techniques Codes des couleurs Schema ElectriqueLégende Schema Electrique suite Utilisation Controle / Preparation DES Batteries SUR UNE Machine NeuveMise en marche de la machine Avant LA Mise EN MarcheMise EN Marche ET Arret DE LA Machine Machine AU Travail Arrêt de la machineEntretien Plan Dentretien Programme Lors de la Toutes ProcédureLes HeuresControle ET Reglage DE LA Hauteur DU Balai Central Remplacement DU Balai Central Remplacement DES Balais Lateraux Controle ET Reglage DE LA Hauteur DES Balais LaterauxNettoyage ET Controle DE Lintegrite DU Filtre a Poussiere Contrôle des volets avant et arrière Controle DE LA Hauteur ET DU Fonctionnement DES VoletsContrôle des volets latéraux Controle / Remplacement Retablissement DES Fusibles Contrôle / remplacement des fusibles à lamelleContrôle des fusibles restaurables ReposeProblème Cause probable Remède Depistage DES PannesMise EN Decharge Table of Contents Manual Purpose and Contents HOW to Keep this Manual Declaration of ConformityTarget Identification DataSpare Parts and Maintenance Other Reference ManualsChanges and Improvements Operation CapabilitiesUNPACKING/DELIVERY SafetySymbols General Instructions English Machine Description Machine StructureMachine Structure Continues ACCESSORIES/OPTIONS Control PanelTechnical Data Colour code Wiring DiagramKey Wiring Diagram Continues Battery CHECK/SETTING on a NEW Machine USEStarting the machine Before Starting the MachineStarting and Stopping the Machine Machine Operation Stopping the machineMaintenance Hours Scheduled Maintenance TableEvery Procedure Upon delivery 100 200 300 400 Main Broom Height Check Adjustment Main Broom Replacement Side Broom Height Check Adjustment Side Broom ReplacementDust Filter Cleaning and Integrity Check Front and rear skirt check Skirt Height and Operation CheckSide skirt check Hood Safety Switch Operation Check Fuse CHECK/REPLACEMENT/RESETLamellar fuse check/replacement AssemblyTrouble Possible cause Remedy TroubleshootingScrapping Inhoudsopgave InleidingInleiding Andere Gebruikershandleidingen Vervangingsonderdelen EN OnderhoudModificaties EN Verbeteringen BedrijfscapaciteitVeiligheid Gebruikte SymbolenVerpakking VERWIJDEREN/AFLEVERING Algemene Instructies Nederlands Gebruiksaanwijzing Beschrijving VAN DE Machine Bouw VAN DE MachineOpbouw VAN DE Machine vervolg Accessoires / Opties Bedieningspaneel EN KnoppenTechnische Eigenschappen Elektrisch Schema KleurcoderingElektrische Installatie vervolg Gebruik Controle / Voorbereidingen Voor Accus OP EEN Nieuwe MachineStarten van de machine Voor HET Starten VAN DE MachineDE Machine Starten EN Stoppen Machine in Bedrijf De machine stoppenOnderhoud Onderhoudsschema Procedure Bij aflevering ElkeDE Hoogte VAN DE Hoofdborstel Controleren EN Afstellen DE Hoofdborstelvervangen DE Hoogte VAN DE Zijborstels Controleren EN Afstellen DE Zijborstels VervangenReiniging EN Contole OP Integriteit VAN HET Stoffilter Controle van de voor- en achterflap Controle VAN DE Hoogte EN Werking VAN DE FlapsControle van de zijflaps Controle / Vervanging / Resetten VAN DE Zekeringen Controle/vervanging van de smeltzekeringenControle van de herbruikbare zekeringen MontageProbleem Waarschijnlijke oorzaak Oplossing Storingen LokaliserenVerwijdering

SR 1100S specifications

The Nilfisk-Advance America SR 1100S is a robust, versatile scrubber designed to meet the diverse cleaning needs of various commercial environments. Ideal for both small and medium-sized spaces, this machine excels in performance, efficiency, and ease of use, making it an excellent choice for businesses looking to achieve a high standard of cleanliness.

One of the standout features of the SR 1100S is its compact and ergonomic design. This allows for easy maneuverability in tight spaces such as aisles, smaller retail environments, and crowded areas. The machine is equipped with a highly efficient brush system that ensures effective scrubbing while reducing water and detergent consumption, enabling operators to achieve optimal results while also being environmentally conscious.

The SR 1100S is powered by a reliable battery system that offers an impressive run time. This allows for extended cleaning sessions without the need for frequent recharging, which can be a significant advantage in busy commercial settings. Additionally, the scrubber features a simple control panel, making it user-friendly for operators of varying skill levels. The intuitive design means that staff can quickly learn to operate the machine, enhancing productivity throughout the organization.

One of the key technologies employed in the Nilfisk-Advance America SR 1100S is the advanced Ecoflex system. This innovative technology enables users to adjust the water and detergent flow according to the specific cleaning needs of each task. This not only helps in conserving resources but also ensures that surfaces are cleaned effectively, regardless of the level of soiling.

Furthermore, the SR 1100S is designed with operator safety in mind. With features that reduce noise levels during operation, it makes it suitable for use in noise-sensitive areas, such as schools and hospitals. The scrubber is also built with maintenance accessibility in mind, allowing for quick and easy servicing, which minimizes downtime.

In conclusion, the Nilfisk-Advance America SR 1100S is a powerful, efficient, and user-friendly scrubber that is backed by advanced technology. Its compact design, effective cleaning capabilities, and operator-friendly features make it a valuable addition to any cleaning fleet. With its commitment to sustainability and efficiency, the SR 1100S is an ideal choice for businesses aiming to maintain a clean and safe environment for employees and customers alike.
Top Page Image Contents