JBL CVPD50, CVR700 manual Tuner Operation, Recording, Output Level Trim Adjustment

VCR Analog Audio/Video Outputs

¤. However, the digital signals will be passed through to the Digital Audio

Outputs ¶bg.

Tuner Operation

The CVR700’s tuner is capable of tuning AM, FM and FM Stereo broadcast sta- tions. Stations may be tuned manually, or they may be stored as favorite station presets and recalled from a 30-position memory.

Station Selection

1. Press the Tuner Button d 2 on the remote to select the tuner as an input. The tuner may be selected from the front panel by turning the Source Selector quntil the tuner is active.

2. Press the Tuner Button d 2 or Tuner Band Selector !to switch between AM and FM so that the desired frequency band is selected.

3.When using the front-panel controls, the Tuning Mode Button 6is used to select the function of the

Tuning/Preset Up/Down Buttons

8. Press the Tuning Mode Button

6to toggle between TUNING and

PRESET. Press the Tuning Mode

Selector o 15 on the remotes to select manual or automatic tuning.

In either mode, each press of the

Tuning Selectors 8vf 27

29will increase or decrease the fre- quency by one increment. When the

Tuning Mode Selector o 15 has

been pressed so that AUTO TUNE appears in the Lower Display Line E, pressing and holding the Tuning Selectors 8vf 27 29 will cause the tuner to scan for the next higher or lower frequency with an acceptable signal. Release the button, and AUTO TUNED will appear in the Lower Display Line Eto indi- cate that a station has been tuned. AUTO ST TUNED will appear in the Lower Display Line Efor FM stereo stations.

When the Tuning Mode Selector

o15 has been pressed so that MANUAL TUNE appears in the

Lower Display Line E, pressing and holding the Tuning Selectors

8vf 27 29 will cause the tuner to scan up or down through all frequencies, stopping when you release the button, even if no accept- able signal is present. The message

MANUAL TUNED will neverthe- less appear in the Lower Display Line E.

4.Stations may also be tuned directly in either the automatic or manual mode. To enter a station’s frequency directly, first select the AM or FM band as desired be pressing the Tuner Button d 2 . Next, press the Direct Button l 9 . Within 5 seconds of when DIRECT IN scrolls in the

Lower Display Line E, enter the station frequency by pressing the

Numeric Keys l 14 . If you press an incorrect button while entering a

direct frequency, press the Exit/ Cancel Button r 8 to start over.

Preset Tuning

Using the remote, up to 30 stations may be stored in the CVR700’s memory for easy recall using the front-panel controls or the remote.

To enter a station into the memory, first tune the station using the steps outlined above. Then:

1.Press the Memory Button @k 28 ; two underlines will flash in the

Upper Display Line H.

2.Within 5 seconds, press the Numeric Keys l 14 corresponding to the memory location where you wish to store this station’s frequency. The pre- set number will appear in the Upper Display Line H.

3.Press the Memory Button @k

28again to store the preset station.

4.Repeat the process after tuning any additional stations to be preset.

NOTE: By its nature, plasma display devices tend to interfere with AM radio reception. In any event, as mentioned elsewhere in this manual, it is preferable to leave the screen off to avoid burn-in when no video signal is present and the startup screen may be displayed for a long time. Therefore, when the AM tuner band is selected as the source, the CVPD50 will automatically enter the standby mode. To wake it, simply select any other source (including the FM tuner band).

Recalling Preset Stations

•To manually select a station previously entered in the preset memory, press the Numeric Keys l 14 for the desired station’s memory location.

•To manually scroll through the list of preset stations, press the Preset

Stations Selector Button 8t

h30 on the front panel or remote. When using the front-panel controls, remember to first press the Tuning Mode Selector 6to select Preset as the function of the Tuning/Preset Buttons 8.

Recording

In normal operation, the audio or video source selected for listening through the CVR700 is sent to the record outputs. This means that any program you are watching or listening to may be recorded simply by placing machines connected to the Digital Recorder Analog Audio/

Video Outputs ‚ or VCR Analog Audio/Video Outputs ¤ in the

record mode.

When a digital audio recorder is connected to the Digital Audio Outputs bg7, you are able to record the digital signal using a CD-R, MiniDisc or other digital recording system.

NOTES:

•The digital outputs are active only when a digital signal is present, and they do not convert an analog input to a digital signal, or change the format of the digital signal. In addition, the digital recorder must be compatible with the output signal. For example, the PCM digital input from a CD player may be recorded on a CD-R or MiniDisc, but Dolby Digital or DTS signals may not.

•Please obey the copyright restrictions on any material you copy. Unauthorized duplication of copyrighted materials is prohibited by law.

Output Level Trim Adjustment

Normal output level adjustment for the CVR700 is established using the test tone, as outlined on pages 50–52. In some cases, however, it may be desirable to adjust the output levels using program material such as a test disc, or a selection you are familiar with. Additionally, the output level for the subwoofer can only be adjusted using this procedure.

To adjust the output levels using program material, first set the reference volume for the front left and front right channels using the Volume Control Óu 12 .

If you are using a disc with test signals or an external signal generator as the source used when the output levels are being trimmed, you may use the remote

64