JBL CVR700, CVPD50 manual Changing Devices, Appears. The available options are

appears. The available options are

DVD/MAIN, SYSTEM, SCREEN, DVI/DVD, TIVO, GAME, CABLE, VCR, TV and FM/AM [TUNER]. We recom- mend that you learn new codes only for devices that are external to the JBL Cinema Vision system. For this example, we will select “DVI/DVD” to enter the codes needed to operate an external DVD player with a DVI output.

L E A R N C O D E

D V I / D V D

Figure 67

4.The next menu screen (Figure 68) will prompt you to select the button on the remote that you wish to program. Press that button on the remote.

P R E S S B U T T O N

T O B E P R O G R A M M E D

Figure 68

5.Once you press the button to be pro- grammed on the remote, press and hold the button on the remote control for the device to be programmed within five seconds, as instructed on the next menu screen (Figure 69).

P R E S S B U T T O N O N

O R I G I N A L R E M O T E

Figure 69

6.Continue to hold the button on the original remote until the menu on the CVR700R2 remote’s LCD screen changes. If the code is successfully learned, you will see the display shown in Figure 70.

C O D E L E A R N E D

C O N T I N U E

Figure 70

If you see that menu, proceed to Step 9. If the code is not successfully learned, you will see the display shown in Figure

71.If that menu appears, proceed to Steps 7 and 8.

C O D E F A I L E D

A G A I N

Figure 71

If you don’t attempt to “teach” a remote code to the CVR700R2 remote within 5 seconds, the words “TIME OUT” will appear briefly on the second line of the LCD display, and you will be prompted to start over by pressing a button on the CVR700R2 remote (see Figure 68).

You may exit the process at any time by pressing the Remote Menu Button b.

7.If the message shown in Figure 71 appears in the display, press the Set Button sto try programming the button again. When the remote prompts you to press and hold the key on the original remote again by show- ing the display shown in Figure 69, immediately press the button on the source remote again. To avoid anoth- er failed attempt, make certain that the windows on the two remotes are facing one another.

8.Continue to hold the button on the original remote until the LCD display changes again. If the code was suc- cessfully learned, you will see the display shown in Figure 70. In that case, go to Step 9.

If the CODE FAILED display (Fig. 71) appears again, you may either try to program the key again, or press the ⁄ Navigation Button qto stop the process. It is possible that some remotes may use code sequences or infrared frequencies that are not com- patible with the CVR700R2 remote, and those codes cannot be learned. When the display shown in Figure 72 appears, press the Set Button s to exit the Learning system.

C O D E F A I L E D

E X I T

Figure 72

9.When a code has been learned suc- cessfully, you have three options. When the display shown in Figure 70 is on the LCD screen on the remote, you may press the Set Button sto learn additional codes from the but- tons on a original source remote into the CVR700R2 remote. Follow Steps 4 through 6 as often as needed to com- plete the code-learning process.

10.If you wish to change the name that appears in the LCD display when the button that has just had a new code learned is pressed, press the ⁄

Navigation Button quntil the display shown in Figure 73 appears in the LCD display. Press the Set Button sto be taken to a EDIT BUTTON display. Enter the new name for the key following the instructions shown in the Renaming Individual Keys sec- tion of this manual on page 86. If you find it more convenient to rename the buttons at a later time, you may do that separately by following the instructions on page 85.

C O D E L E A R N E D

E D I T B U T T O N

Figure 73

11.When you have programmed all keys for the desired device, press the ⁄

Navigation Button qrepeatedly when the LEARN MENU (Figure 70) appears until you see the display shown in Figure 74. Press the Set Button sto return the remote to normal operation.

C O D E L E A R N E D

E X I T

Figure 74

12.If you wish to program the codes for another device, repeat the procedure outline above, but select a different device in Step 3.

Note on Learning Function: Remote control signals can vary from one con- troller to the next due to different stan- dard formats adopted by each manufac- turer. For example, some manufacturers repeat the code sequence in the initial transmission, and others insert a special code to identify the brand or model. Due to the variety of formats, occasionally an error may occur in the learning process even though the CVR700R2 remote has indicated that the code was learned cor- rectly. Therefore, it is recommended that you test the newly learned codes with the source component. If the code was not learned correctly, try relearning it. Usually, after several tries, the code can be learned correctly.

Changing Devices

In the factory default settings, the remote is programmed so that the commands transmitted correspond to the device selected by pressing one of the Input Selectors 3. This is logical, as you want the remote to control the device you have selected. However, in some circum- stances you may have configured your system so that the devices connected

to the CVR700 do not correspond to the default device settings and the legends printed on the remote. For example, if your system has two VCRs you may connect the second VCR to the digital recorder input. There is no problem in doing that, but in normal operation the commands issued after selecting the digi- tal recorder input are not for a VCR.

The remote allows you to correct that sit- uation through the “Changing Devices” process. This enables you to assign the codes from one type of device to a differ-

79