JBL CVPD50, CVR700 manual Macro Programming, Set Button s

ent button. For example, in the steps below, we will explain how to program the digital recorder buttons to provide the commands to operate a VCR. Of course, you may program the remote to have any of the devices take on the code set of any other device, as your system requires. And, with the remote’s “Edit” function, you can even change the way the name of the device appears on the remote’s LCD display so that you see exactly which commands are being sent.

NOTE: You may not change the device types for the DVD/MAIN device (CVR700’s internal DVD/CD changer), the FM/AM (TUNER) device, the SCREEN device (controls CVPD50 functions) or the SYSTEM device (controls CVR700’s receiver functions).

To program the buttons normally assigned to one device for the commands of another, follow these steps:

1.Press and hold the Remote Menu Button bfor about 3 seconds while the message shown in Figure 54 appears in the remote’s LCD Information Display 2. Release the button when the red light under the Set Button sappears.

2.The remote’s MAIN MENU message (Figure 55), will appear in the LCD display and the Set Button swill remain illuminated in red. Press the ⁄ Navigation Button quntil

CHANGE DEVICE appears on the bottom line of the LCD screen, as shown in Figure 75. Press the Set Button sto begin the process of reassigning the commands used for a particular device.

M A I N M E N U

C H A N G E D E V I C E

Figure 75

3.Next, you will select the Input Selector dfor the device that you wish to change. When the display shown in Figure 76 appears, press the ⁄/¤ Navigation Button qto scroll through the list to find the device you wish to use for another function. In this case, we will select “TIVO,” and show how to change it to take on the codes for operating a VCR. When that device’s name appears, press the Set Button s.

O L D D E V I C E T Y P E

T V

Figure 76

80

4.Once the “old” device type has been selected, you need to tell the remote which set of remote codes to use as a replacement for the device just selected. When the instructions shown in Figure 77 appear, press the ⁄/¤ Navigation Button qto scroll through the list of device categories to find the name of the device that you wish to use. The old device name will remain on the left side of the LCD screen, while the replacement device list will scroll to its right. For example, press the ⁄ Navigation Button quntil the display screen reads TIVO<-VCRto have the digi- tal recorder Button transmit the com- mands used to control a VCR. Press the Set Button swhen the desired device combination appears.

N E W D E V I C E T Y P E

T I V O < - V C R

Figure 77

5.Once the new device is selected, the remainder of the process will select the codes for the specific brand to be used, and for that reason they are identical to the way a device is programmed using manual entry. Continue the process as outlined in the next few steps, remembering that if the codes for your specific device are not found, you may select any brand and then “learn” the proper codes into the remote using the process outlined on page 78. To begin the process, start by selecting the brand of device, as shown in Figure 57. Press the ⁄/¤ Navigation Button quntil the brand name of the device you are programming into the remote appears on the lower line of the display and then press the

Set Button s.

6.The next step is important, as it determines which codes will operate the source device or display. Point the remote at the device being pro- grammed and, following the instruc- tions shown on the remote’s LCD Information Display 2, press and release the Numeric Keys l one at a time, starting with the “1” Button l. After you press the “1” Button l, the remote’s LCD screen will briefly go blank as the code is being transmitted, but you will see the “transmit” icon in the upper right corner of the display to serve as con- firmation that the remote is sending out commands.

7.After you press and release the num- ber key, watch the device being pro- grammed to see whether it turns off. As shown in the instructions that will appear on the next menu screen (Figure 61), press the Set Button s, and then skip to Step 9. If the unit does not turn off, proceed to the next step.

8.If the device being programmed into the remote does not turn off after you have pressed the “1” Button l, continue Steps 6 and 7 by pressing the available numeric keys shown until the device turns off. If the device still does not turn off after all choices have been tried, the code for this specific device is not in the remote library under that brand name. If that is the case, we suggest that you press the Set Button sto accept the codes from another brand so that the programming is completed, but remember that you will then have to program the remote manually by fol- lowing the Learning Commands instructions on page 78.

9.When the device being programmed does turn off after a numeric key has been pressed, you must press the Set Button swithin five seconds to enter the setting into the remote’s memory. After you press the Set but- ton, the top line of the LCD display will read SAVING... and then the word SAVED will flash four times in the center of the bottom line.

10.When the codes are saved the remote will return to normal operation, and whenever you press the Input Selector Button 3that was just programmed, the display will show the original device type code at the far left side of the display, with the name of the new code set type in brackets. For example, the display will read TIVO<-VCRin our exam- ple of replacing the TiVo codes with those for a VCR.

Macro Programming

Macros enable you to easily repeat fre- quently used combinations of multiple remote control commands with the touch of a single button. Once a macro is pro- grammed, you may send up to 20 com- mands with one press of the Power On or Macro buttons. This will greatly simplify the process of turning on your system, changing devices or other common tasks. Thanks to the remote’s two-line display, it