JBL CVPD50 manual Programming the CVR700R1 Remote

PROGRAMMING THE CVR700R1 REMOTE

92

In addition to its powerful CVR700R2 remote control, the JBL Cinema Vision system also includes a smaller CVR700R1 remote intended for everyday use. This remote features many of the same func- tions as the main remote, including the capability of controlling most popular brands of audio and video equipment, such as CD players, cable boxes, digital recording devices, VCRs, satellite receivers and HDTV set-top tuners, but in a more compact design.

The CVR700R1 remote control is capable of operating up to nine devices, including the CVR700. In order to segregate the control commands for each device, the remote’s logic contains a separate “page” of commands for each device called up when that device's selector has been pressed. For example, in order to access the commands that control the CVPD50 screen, such as Letterbox or PIP, you must first press the Screen Selector 34 , and an orange light underneath that but- ton will light. When you press another button on the remote that is used to con- trol the screen, the light underneath the Screen Selector 34 will blink to con- firm the current mode.

Programming Product Codes

The remote is factory-programmed for all CVR700 functions, as well as those of JBL DVD players. In addition, by following one of the methods below, you may program the remote to operate a wide range of devices from other manufacturers.

The Input Selectors 2 10 each may be programmed with one of several device types, as listed in the table below. Unlike the main remote control, the device types on the secondary remote control may not be reassigned. It is important to program your external devices into the correct cor- responding source buttons so that the desired remote control commands will be available for use with your device.

Source	Device Types
Button
AUX	TV, HDTV, VCR, DVD, CD,
	Cable, Satellite
VCR	VCR
CBL/SAT	Cable, Satellite, HDTV
Game/	Game, Camcorder
Cam
DR	DVD-R, CDR, DVHS, TIVO, PVD
	(DVR/PVR – Personal Video
	Recorder)
DVI/	DVI/DVD, DVI/CBL, DVI/SAT,
COMP	HDTV

The DVD, Tuner, Screen and System selec- tors may not be reprogrammed.

Direct Code Entry

This method is the easiest way to program your remote to work with different products.

1.Use the tables in the following pages to determine the three-digit code or codes that match both the product type (e.g., VCR, TV) and the specific brand name. If there is more than one number for a brand, make note of the different choices.

2.Turn on the unit you wish to program into the secondary remote.

3.Press and hold both the Input

Selector 2 10 for the product you wish to control (e.g., VCR, TV) and

the Program Button 21 at the

same time. When the light under the

Input Selector 2 10 stays lit, release the buttons. It is important that you begin the next step within

20 seconds.

4.Point the remote toward the unit to be programmed, and enter the first three- digit code using the Numeric Keys

14 . If the unit turns off, the correct code has been entered. Press the

Input Selector 2 10 again, and note that the red light will flash three times before going dark to confirm the

entry. If the Input Selector 2 10 flashes nine times instead of three times, it means that the code was not accepted. Check the code table to ver- ify the code, and reenter it. If you wish to exit the program mode, press and hold any Input Selector 2

10for 2 seconds.

NOTE: Since video game consoles and camcorders do not have Power Off codes, look for your game device to execute the “Stop” function, and your camcorder to execute the “Zoom In” function.

5.If the device to be programmed in does NOT turn off, continue to enter three-digit codes until the equipment turns off. At this point, the correct

code has been entered. Press the

Input Selector 2 10 again and

note that the light under the Input

Selector 2 10 will flash three times before going dark to confirm the entry.

6.Try all of the functions on the remote to make certain that the product oper- ates properly. Keep in mind that many manufacturers use a number of differ- ent combinations of codes, so it is a good idea to make certain that not only the power control, but the vol-

ume, channel and transport controls work as they should. If functions do not work properly, you may need to use a different remote code.

7.If a code cannot be entered to turn the unit off, if the code for your prod- uct does not appear in the tables in this manual, or if not all functions operate properly, try programming the remote with the Auto Search Method.

Auto Search Method

If the unit you wish to include in the remote is not listed in the code tables in this manual or if the code does not seem to operate properly, you may wish to pro- gram the correct code using the Auto Search method that follows:

1.Turn on the unit that you wish to include in the remote.

2. Press the Input Selector	2 10 for
the type of product to be entered and
the Program Button 21	at the

same time. Hold both buttons until the red light under the Input Selector

2 10 stays lit. The next step must take place while the light is on, and it must begin within 20 seconds after the light appears.

3.Point the remote toward the unit to be programmed, and press either the ⁄ or ¤ Button 4 . Each press will send out a series of codes from the remote’s

built-in database. When the unit being programmed turns off, release the ⁄/¤ Button 4 , as that is your indi- cation that the correct code is in use.

4. Press the Input Selector 2 10 ; the light under it will flash three times before going dark to confirm the entry.

5.Try all of the functions on the remote to make certain that the product oper- ates. Keep in mind that many manu- facturers use a number of different combinations of codes, and it is a good idea to make certain that not only the power control works, but also the volume, channel and transport controls, as appropriate. If all func- tions do not work properly, you may need to Auto-Search for a different code, or enter a code via the Direct Code Entry method.