JBL CVR700 Learning Codes, Macros, Selectors 2, Input Selector 2 10 blinks, Erasing Learned Codes

For future reference, enter the setup codes for the equipment in your system here:

Source	Device	Product
Button	Type	Code
AUX
VCR
CBL/SAT
GAME/CAM
DR
DVI/COMP

Learning Codes

In addition to using codes from the remote’s internal code library, the remote is able to “learn” codes from remotes that may not be in the code library. Also, you may use this function to “learn over” the codes from a preprogrammed device to add functions not included in the prepro- grammed codes. To learn or transfer codes from an original remote to the sec- ondary remote, follow these steps:

1.Place the front of the original remote with the code being sent so that it is

facing the IR Transmitter 40 on the secondary remote “head to head.” The remotes should be between 1 and 3 inches apart.

2.Select the button on the remote that you wish to use as the device selector for the codes about to be entered.

This may be any of the Input

Selectors 2 10 .

3. Press the chosen Input Selector 2

10and the Learn Button 19 at the same time. Hold these buttons until the light under the device selector but- ton turns on. Release the buttons.

4.Press the button on the secondary remote that you wish to program.

5.Within 5 seconds, press and hold the button on the original remote that you wish to “teach” into the secondary remote. When the light under the

Input Selector 2 10 blinks.

NOTE: If the Input Selector 2 10 flashes nine times during Step 5, the programming was not successful.

Repeat the steps to see whether the code will “take.”

6.Repeat Steps 4 through 6 for each button on the source remote that you wish to transfer to the remote.

7.Once all codes have been transferred from the original source remote to the

secondary remote, press the Input

Selector 2 10 you pressed in Step 2. It will blink three times and go dark, exiting learning mode.

8.Repeat Steps 1 through 7 for any addi- tional remotes you wish to “teach” into the secondary remote.

Note on Learning Function: Remote control signals can vary from one controller to the next, due to different standard for- mats adopted by each manufacturer. For example, some manufacturers repeat the code sequence in the initial transmission, and others insert a special code to identify the brand or model. Due to the variety of formats, occasionally an error may occur in the learning process, even though the CVR700R1 remote has indicated that the code was learned correctly. Therefore, it is recommended that you test the newly learned codes with the source component. If the code was not learned correctly, try relearning it. Usually, after several tries, the code can be learned correctly.

Erasing Learned Codes

The remote allows you to remove or erase the code set for all the codes that have been programmed into specific device buttons.

To erase all codes within a single device, follow these steps:

1. Press and hold both the Input Selector

2 10 within which the individual button to be erased has been pro- grammed and the Learn Button 19 .

2.When the LED under the Input Selector turns on, release the buttons.

3.Press and release the Input Selector

2 10 for 3 seconds.

4. The light under the Input Selector 2

10will blink three times and go dark, and all of the learned codes for that device will have been erased.

Macros

Several macro-type commands have been preprogrammed into the remote, and they may be activated by pressing and holding certain other buttons as described below. (The secondary remote does not allow you to program new macro functions.)

1.Pressing and holding the Power On

1or Power Off 39 buttons will execute the Power On (All) or Power Off (All) commands to either turn on or turn off all devices whose product codes have been programmed into the remote. Note that if you are not using any external devices, you may simply

power on the CVR700, and the CVPD50 screen will automatically be triggered to turn on as well.

2. Pressing and holding certain Input

Selectors 2 10 will cause the CVR700 to switch to the selected source input device, and the device will begin playing.

a. Press and hold the DVD Selector

2, and the CVR700 will switch to the internal DVD/CD changer source. If you do not enter the number for a disc you desire to play, the last played disc will begin playing.

b.Press and hold the CBL/SAT

Selector 2 , and the CVR700 will switch to the source device connected to the cable/satellite inputs. If you have programmed the cable or satel- lite set-top box’s remote control codes, the device will be turned on.

c. Press and hold the VCR Selector

2and the CVR700 will switch to the source device connected to the VCR inputs. If you have programmed the VCR’s remote control codes, the device will be turned on, and the play command will be transmitted to it.

d.Press and hold the DR (Digital Recorder) Selector 10 , and the CVR700 will switch to the source device connected to the DR inputs. If you have programmed the DR’s remote control codes, the device will be turned on, and the play command will be transmitted to it.

e.Press and hold the AUX Selector

2, and the CVR700 will switch to the source device connected to the AUX inputs. If you have programmed the device’s remote control codes, the device will be turned on, and the play command will be transmitted to it.

f.Press and hold the Game/Cam Selector 10 , and the CVR700 will switch to the source device connected to the Game/Cam inputs. If you have programmed the device's remote control codes, the play command will be transmitted to it. Note that for video game consoles and cam- corders, there are no power on or off commands. Therefore, only the Play command (or start/stop com- mand for camcorders) will be transmitted.

93