JBL CVPD50, CVR700 manual Learning Commands

example, we will select “HDTV- Tuner” to enter the codes needed to operate your HDTV set-top box.

6.At the next menu screen on the remote, press the ⁄ Navigation Button qso that the bottom line of the LCD display reads AUTO (Fig. 62) and then press the Set Button sto enter the Automatic programming mode.

P R O G R A M D E V I C E

A U T O

Figure 62

7.As instructed on the next menu screen, press the ⁄ Navigation Button qto begin the automatic code search process. Your confirma- tion that the remote is sending out commands is the movement of a square block across the top line of the LCD display screen while the bot- tom line reads PLEASE WAIT…. You will also see the transmit icon in the upper right corner of the LCD dis- play’s top line to remind you that the remote is working even though you may not see anything happening to the device being programmed.

8.It will take a few seconds for the remote to send out the first group of commands, after which you will see a new display in the LCD screen, as shown in Figure 63. Following the instructions, if the device being pro- grammed has not turned off, press the ⁄ Navigation Button qagain to send another group of codes (see Step 9). If the device being programmed has turned off, press either the “1” or “0” key and skip to Step 10.

P O W E R O F F ?

Y - > 1 ~ 0 N - >

Figure 63

9.By pressing the ⁄ Navigation Button qagain, the remote will send out a new set of commands. When it pauses, follow the instruc- tions shown in Step 8. Depending on how many codes are stored for a specific device type, you may have to repeat this process as many as 15 times. Remember, if the device turns off, skip to Step 10. When all the codes for the device being pro- grammed have been tried, the instruction shown in Figure 64 will appear. This means that the codes for the product you are trying to program are not in the remote library and you

will have to “learn” them into the remote following the instructions shown in the next section. Press the Remote Menu Button bas instructed to exit the programming process.

R E A C H E N D P O I N T

P R E S S R E M K E Y

Figure 64

10.If the device being programmed does turn off after following the instruc- tions in Step 7, you will need to verify the code set by pressing the

Numeric Keys lin sequence, as instructed in Figure 60. Point the remote at the device being pro- grammed, and press the “1” Button lto see whether the device turns back on.

11.After pressing and releasing the “1” Button l, check to see whether the device has turned back on. If it has, skip to Step 12. If it does not turn off, press the “2” Button l, or the next button in the numeric sequence if you are repeating the pro- cedure, as instructed by the LCD screen in Figure 65.

P O W E R O N ?

Y - > S E T N - > 1 ~ 0

Figure 65

12.When pressing the “1” button does not turn the device being programmed back on, repeat the procedure by try- ing the remainder of the Numeric Keys lin sequence, each time pressing and then releasing the but- ton to see whether the new device turns back on. When it does, skip to the next step. However, if you try all 10 numeric keys and find that the unit will not turn on, you won’t be able

to use this method to program the device. Press the Remote Menu Button bto exit the programming process. You’ll need to follow the Learning Commands instructions below to enter the codes for this device into the remote.

13.When pressing one of the numeric keys in Step 11 or 12 causes the device being programmed to turn back on, follow the instructions shown in Figure 65 and press the Set Button swithin five seconds of the device turning on. After you press the Set button, the top line of the LCD display will read SAVING… and

then the word SAVED will flash four times in the center of the bottom line.

14.When the codes are saved, the remote will return to normal opera- tion, and whenever you press the

Input Selector Button dthat was just programmed, the codes for the new device will be used.

Learning Commands

On occasions when the remote does not contain the codes for a particular prod- uct’s remote in its built-in library, or when you wish to program a missing or special function into one button of a device, the remote’s learning capability allows you to do that. To teach commands from one product’s remote into the remote, follow the steps below:

The process requires that both the device’s original remote and the CVR700R2 remote be available. Before pressing any buttons on either remote, place them so that the IR transmitter on the remote from the device to be pro- grammed is facing the Infrared Lens son the CVR700R2 remote, pointing to the area next to the slots over the EzSet Microphone Sensor r. The two remotes should be no more than an inch apart, and there should not be any direct sunlight or other bright light source near the remotes.

1.Press and hold the Remote Menu Button bfor about 3 seconds while the message shown in Figure 54 appears in the remote’s LCD Information Display c. Release the button when the red light under the Set Button sappears.

2.The remote’s MAIN MENU message (Figure 55), will appear in the LCD display and the Set Button swill remain illuminated in red. Press the ⁄ Navigation Button quntil

LEARN appears on the bottom line of the LCD screen, as shown in Figure 66. Press the Set Button sto begin the process of learning com- mands from another device’s remote into the remote.

M A I N M E N U

L E A R N C O D E

Figure 66

3.LEARN CODE will appear in the LCD display (Figure 67). Press the ⁄/¤ Navigation Controls qto scroll through the list of sources and press the Set Button swhen the source you wish to set the codes for

78