JBL CVR700 manual Punch-Through Configuration, Volume Punch-Through, Channel Control Punch-Through

Punch-Through Configuration

Punch-through is a capability of the remote that allows the Volume controls, Channel Up/Down buttons or Transport keys (Play, Stop, Record, Pause, Fast Forward and Reverse, and Skip Up/Down) to link to a different device. For example, if your TV, cable box or satellite receiver is connected through the CVR700, you will most likely want to use the CVR700’s volume control commands even when the remote has been set to issue all other commands for the video device. “Punch- through” enables you to easily program the remote to do this.

Volume Punch-Through

Follow these steps to enable the Volume Up/Down and Mute controls from one device to be used when the remote is otherwise programmed for a different device.

NOTE FOR VOLUME PUNCH-

THROUGH: The remote’s default settings are for the CVR700’s volume controls, to be used when any input or device is selected, with the exception of the Game/Cam button. There is no need to program the remote for volume punch- through for the CVR700’s controls with other sources, such as DVD. To have the CVR700’s volume commands used when the Game/Cam device is selected, follow these steps:

1.Press and hold the Remote Menu Button bfor about three seconds while the message shown in Figure 54 appears in the remote’s LCD Information Display 2. Release the button when the red light under the Set Button sappears.

2.The remote’s MAIN MENU message (Figure 55), will appear in the LCD display and the Set Button swill remain illuminated in red. Press the ⁄/¤ Navigation Button quntil

PUNCH-THROUGH appears on the bottom line of the LCD screen, as shown in Figure 88. Press the Set Button sto enter the main punch- through menu branch.

M A I N M E N U

P U N C H - T H R O U G H

Figure 88

3.At the next menu screen (Figure 89), press the Set Button sto begin programming the remote for Volume punch-through.

P U N C H - T H R O U G H

V O L U M E

Figure 89

4.The next display screen (Figure 90) is where you select the device that will receive the punch-through commands. In our example, that is the Game/Cam button, as that is where we want the CVR700’s volume controls to be active. Press the ⁄/¤ Navigation Button quntil the name of the base device appears and then press the Set Button s.

D E V I C E I N U S E

T V

Figure 90

5.At the next display screen (Fig. 91), you will select the device whose Volume Up/Down and Mute com- mands will be used. Press the ⁄/¤

Navigation Button quntil the desired device’s name appears to the right of the device in use. In our example, that is the CVR700 (indicated by M/DVD). When the desired combination of devices appears, press the Set Button s.

P U N C H - T H R O U G H

G A M E < - M / D V D

Figure 91

6.When the Set button is pressed, the display will change to show you that the new combination of control com- mands is being saved to the unit’s memory, as shown in Figure 92. The word SAVED will flash four times and then the remote will return to normal operation.

G A M E < - M / D V D [ V O L ]

S A V E D

Figure 92

7.Once the punch-through is pro- grammed, the Volume Up/Down and Mute buttons of the second device named will be used when those con- trols Kare pressed while the mas- ter device is in use.

Returning the Volume Control Settings to Default Operation

If you wish to remove the Volume punch- through so that the commands for Volume and Mute are returned to the factory default setting, follow the steps shown above, except that in Steps 4 and 5, select the same device for both the DEVICE IN USE on the left side of the bottom line and the PUNCH-THROUGH

device. In the example used, the display to return the remote to default settings will appear as shown in Figure 93.

P U N C H - T H R O U G H

G A M E < - G A M E

Figure 93

Channel Control Punch-Through

Channel punch-through allows the Channel Up/Down buttons to send com- mands to a different device than the one that has been selected for other com- mands. For example, you may wish to use a cable box or satellite receiver as the source for a VCR, so you would want the Channel Up/Down Controls gto transmit commands to the cable box even though the other button commands are programmed to operate the VCR.

To program the remote for channel punch-through, follow these steps. This example will show how to program chan- nel punch-through so that the commands programmed for Channel Up/Down for the Cable device will be transmitted when the VCR device has been selected as the current device.

1.Press and hold the Remote Menu Button bfor about 3 seconds while the message shown in Figure 54 appears in the remote’s LCD Information Display 2. Release the button when the red light under the Set Button sappears.

2.The remote’s MAIN MENU message (Figure 55), will appear in the LCD display and the Set Button swill remain illuminated in red. Press the

⁄/¤ Navigation Button quntil

PUNCH-THROUGH appears on the bottom line of the LCD screen, as shown in Figure 88. Press the Set Button sto enter the main punch- through menu branch.

3.At the next menu screen, press the

⁄/¤ Navigation Button quntil

CHANNEL appears on the bottom line of the LCD screen, as shown in Figure 94. Press the Set Button s to begin programming the remote for channel punch-through.

P U N C H - T H R O U G H

C H A N N E L

Figure 94

4.The next display screen (Figure 95) is where you select the device that will receive the punch-through commands. In our example, that is the VCR button, as that is where we want the cable

83