next letter needed is a “U,” so you would press the “8” button twice.
b. To enter a letter that uses the same numeric key, you must first press the › Navigation Button qto move the blinking cursor block to the next position. Then press the Alphanumeric Key l as required to enter the desired letter. This is the way you would enter the second “L” in the word “FULL”.
c. To enter a blank space, press the › Navigation Button qtwice. The first press will move the cursor to the right, and the second press will move the cursor one more space to the right, leaving a blank space between the last letter and the next one.
9.Repeat Steps 7 and 8 as needed to complete entering the needed letters, numbers, characters and spaces.
10.When the text entry is complete, press the Set Button s. The new name will be entered into the remote’s memory, replacing the default name.
11.At this point, you have two options:
a.The screen shown in Figure 113 will appear, prompting you to con- tinue renaming. Press the Set Button sto select CONTINUE.
R E N A M E B U T T O N
C O N T I N U E
Figure 113
The remote will return to the PRESS
ABUTTON menu option (Fig. 111) as shown in Step 6. Repeat the in- structions in Steps 6 though 11 to rename the next button.
b. If you have no additional buttons to rename, press the ⁄ Navigation Button ountil the menu screen displays EXIT on the bottom line of the display. Press the Set Button sto return the remote to normal operation.
NOTES ON RENAMING KEYS:
•Renaming a button does not change its function. You may change the function of an individual button by “learning” a new code into the remote. See page 78 for more information.
•When a button is renamed, it will only apply to the specific device selected in Step 4. The same button may be renamed as needed for each individual device
with which it is used. There is a limit of nine characters (including spaces) for any new device or button name.
Resetting the Remote
Depending on the way in which the remote has been programmed, there may be a situation where you wish to totally erase all changes that have been made to the remote and return it to the factory defaults. You may do that by following the steps shown below, but remember that once the remote is reset, ALL changes that have been made, including programming for use with other devices, learned buttons, macros,
To erase all settings and reset the remote to the original factory default settings and displays, follow these steps:
1.Press and hold the Remote Menu Button bfor about three seconds while the message shown in Figure 54 appears in the remote’s LCD Information Display 2. Release the button when the red light under the Set Button sappears.
2.The remote’s MAIN MENU message (Figure 55), will appear in the LCD dis- play and the Set Button swill remain illuminated in red. Press the ⁄/¤ Navigation Button quntil
USER RESET appears on the bot- tom line of the LCD screen, as shown in Figure 114.
M A I N M E N U
U S E R R E S E T
Figure 114
3.Press the Set Button sto reset the remote. Note that once the Set button is pressed, the process may not be stopped. A RESETTING...
message will appear in the upper line of the remote’s LCD screen, as shown in Figure 115, while the remote’s memory is being cleared. It may take a few minutes for the reset process to take place, and the length of time will vary depending on how much customization and programming has taken place. Please be patient; as long as the message appears in the display the remote is functioning properly.
R E S E T T I N G . . .
Figure 115
4.When the remote has been totally reset and returned to the factory default condition, a REMOTE RESET COMPLETE message will appear (Figure 116) briefly, and then the remote will return to normal operation.
R E M O T E R E S E T
C O M P L E T E
Figure 116
If the remote locks up for some reason and you wish to reset it without losing any programming or removing and replac- ing the batteries, you may perform a soft reset by removing the cover from the bat- tery compartment and gently pressing the small black rectangular button labeled “RESET”. This should return the remote to normal operation.
Additional Notes on Configuring and
Operating the Remote
•In normal operation, the last selected device will appear in the upper line of the LCD Information Display 2.
After one minute with no activity, the remote will go into standby mode and the display will go blank to conserve power. Simply press any button to return the remote to normal operation.
•When the remote is being programmed, it will automatically
The message shown in Fig. 117 will appear briefly, and the remote will then exit the feature being programmed and any data entered will be lost.
T I M E O U T O R
R E M K E Y P R E S S E D
Figure 117
•The programming or configuration process may also be stopped at any time by pressing the Remote Menu Button b. The message shown in Figure 117 will appear, the data entered in the current process will be lost and the remote will return to nor- mal operation. Any process that was underway when the button will be pressed must be restarted.
•In most situations, you may press the
Exit/Cancel Button Hto simply exit the current function and return to the previous menu screen. The Cancel function is not always available, in which case you may need to exit the remote's menu system altogether by pressing the Remote Menu Button B.
87
