to the cable/satellite inputs. If you have programmed the cable or satel- lite
c. Press and hold the VCR Selector 3, and the CVR700 will switch to the source device connected to the VCR inputs. If you have programmed the VCR's remote control codes, the device will be turned on, and the play command will be transmitted to it.
d. Press and hold the DR (Digital Recorder) Selector 3, and the CVR700 will switch to the source device connected to the DR inputs. If you have programmed the DR's remote control codes, the device will be turned on, and the play com- mand will be transmitted to it.
e. Press and hold the AUX Selector 3, and the CVR700 will switch to the source device connected to the AUX inputs. If you have programmed the device's remote control codes, the device will be turned on, and the play command will be transmitted to it.
f. Press and hold the Game/Cam Selector 3, and the CVR700 will switch to the source device connected to the Game/Cam inputs. If you have programmed the device's remote control codes, the play command will be transmitted to it. Note that for video game consoles and cam- corders, there are no power on or off commands. Therefore, only the Play command (or start/stop command for camcorders) will be transmitted.
g. Press and hold the DVI Selector 3, and the CVR700 will switch to the source device connected to the DVI inputs. If you have programmed the device's remote control codes, the device will be turned on, and the play command will be trans- mitted to it.
3.The PIP Swap Button cis activated while in screen mode by pressing and holding that button until the video source in the
Erasing a Macro
Once a macro has been created and stored in the remote’s memory, you have the option of erasing it (except the pre- programmed macros). You may do this at any time by following these steps:
1.Press and hold the Remote Menu Button bfor about 3 seconds
while the message shown in Figure 54 appears in the remote’s LCD Information Display 2. Release the button when the red light under the Set Button sappears.
2.The remote’s MAIN MENU message (Figure 55), will appear in the LCD display and the Set Button swill remain illuminated in red. Press the ⁄ Navigation Button qso that
MACRO appears on the bottom line of the LCD screen, as shown in Figure 78. Press the Set Button sto enter the main macro menu branch.
3.At the next menu screen (Figure 84), press the ⁄/¤ Navigation Button ountil the bottom line in the remote’s LCD display reads ERASE A MACRO. Press the Set Button q to begin the process of erasing a macro.
M A C R O
E R A S E A M A C R O
Figure 84
4.The next display screen (Figure 85) is where you select which macro will be erased. Press the ⁄/¤ Navigation Button quntil the number of the macro you wish to erase appears. For this example we will erase the Power On macro created in the previous sec- tion. When the name of the macro to be erased appears, press the Set Button s.
E R A S E A M A C R O
M I C R O 1
Figure 85
5.The word ERASED will flash four times in the bottom line of the remote’s LCD display, and then the display will return to its normal condi- tion. When that happens, the macro is erased and the remote is returned to normal operation.
Read a Macro
To check the commands stored in the remote’s memory for one of the macro buttons, follow these steps:
1.Press and hold the Remote Menu Button bfor about three seconds while the message shown in Figure 54 appears in the remote’s LCD Information Display 2. Release the button when the red light under the Set Button sappears.
2.The remote’s MAIN MENU message (Figure 55), will appear in the LCD display and the Set Button swill
remain illuminated in red. Press the
⁄Navigation Button quntil
MACRO appears on the bottom line of the LCD screen, as shown in Figure 78. Press the Set Button sto enter the main macro menu branch.
3.At the next menu screen, press the
⁄/¤ Navigation Button quntil the bottom line in the remote’s LCD display shows READ A MACRO (Figure 86). Press the Set Button s to begin the process of reading a macro.
M A C R O
R E A D A M A C R O
Figure 86
4.The next display screen (Figure 87) is where you select the macro to be read. Press the ⁄/¤ Navigation Button quntil the name of the macro you wish to read appears. For this example, we will read back the Micro 1 macro created in a previous section. When the name of the macro to be read appears, press the Set Button s.
R E A D A M A C R O
M I C R O 1
Figure 87
5.As soon as the Set button is pressed, the first two steps in the macro will be appear in the remote’s LCD screen. You may then use the ⁄/¤ Navigation Button qto step
up or down through the list of com- mands stored as the macro. As you read the display, you will see Input Selector Buttons 3appear in brackets, (e.g., [M/DVD]). When the step in the macro is a function, navigation or any other button, it will appear next to the bracketed
6.When you are finished reviewing the macro’s contents, press the Set Button sto return the remote to normal operation.
NOTE: It is not possible to edit the steps in a macro. If you notice an error, you will need to erase the macro as described above, and reprogram all of the steps.
82
