Nilfisk-Advance America SR 1100S Side Broom Height Check Adjustment, Side Broom Replacement

Page 70

ENGLISH

USER MANUAL

SIDE BROOM HEIGHT CHECK AND

ADJUSTMENT

NOTE

Brooms with harder or softer bristles are available. This procedure is applicable to all types of brooms.

1.Check the side broom distance from the ground, according to the following procedure:

•Drive the machine on a level ground and lower the side brooms.

•Keep the machine stationary and turn on the side brooms for a few seconds.

•Lift the side brooms, then move the machine and turn it off.

•Check that the side broom prints are as shown in the fi gure (A and B, Fig. 6).

If the print is not within specifi cations, adjust the broom height, according to the procedure shown in step 2.

2.Engage the parking brake with the pedal (3) and the lever

(4).

3.Turn the ignition key (82) to "0".

4.Loosen the knob (A, Fig. 7) positioned above the broom.

5.Turn the knob (B, Fig. 7) and remind that:

•It must be screwed to lift the broom;

•It must be unscrewed to lower the broom.

After the adjustment, hold the knob (B) and tighten the knob (A).

6.Perform step 1 again to check the proper adjustment of the side broom height.

7.When the brooms are too worn and can no longer be adjusted, replace them according to the procedure shown in the relevant paragraph.

SIDE BROOM REPLACEMENT

NOTE

Brooms with harder or softer bristles are available. This procedure is applicable to all types of brooms.

CAUTION!

It is advisable to wear protective gloves when replacing the side brooms because there can be sharp debris between the bristles.

1.Drive the machine on a level ground and engage the parking brake with the pedal (3) and the lever (4).

2.Turn the ignition key (82) to "0".

3.Lay the hand inside the side broom and press the tabs (A, Fig. 8) inwards, then remove the broom (B) by disengaging it from the four pins (C).

4.Install the new side broom by engaging it on the pins (C, Fig. 8) and on the tabs (A).

5.Check and adjust the side broom height as shown in the previous paragraph.

S311394

Figure 6

S311395

Figure 7

S311396

Figure 8

20

146 2559 000(2)2007-02 A

SR 1100S P

Page 69 Page 71
Image 70
Page 69 Page 71
Contents Sweeper SR 1100S P 146 2559 00022007-02 aSweeper SR 1100S PInhaltsverzeichnis SR 1100S PEinleitung Änderungen UND Technische Verbesserungen Andere ReferenzanleitungenErsatzteile UND Wartung FunktionseigenschaftenAUSPACKEN/AUSLIEFERUNG Benutzte SymboleSicherheit Allgemeine Hinweise Deutsch Betriebsanleitung Maschinenbeschreibung Maschinenaufbau63 64 Schalttafel UND Bedienelemente ZUBEHÖRE/OPTIONENTechnische Daten Schaltplan FarbencodesSchaltplan fortgesetzt Betrieb PRÜFUNG/VORBEREITUNG DER Batterien AN Einer Neuen MaschineMaschinenanlassen UND -ABSTELLEN VOR DEM Anlassen DER MaschineMaschinenanlassen Maschine in Betrieb MaschinenabstellenWartung Alle Übersichtstabelle DER Planmässigen WartungVorgang StundenPrüfung UND Einstellung DER Hauptkehrwalzenhöhe Ersetzen DER Hauptkehrwalze Die entsprechende Nabe a eingefügt wirdPrüfung UND Einstellung DER Seitenbesenhöhe Ersetzung DER SeitenbesenReinigung UND Vollständigkeitsprüfung Desb C E Staubfilters Prüfung der Seitenflaps Prüfung DER Flapshöhe UND FunktionsfähigkeitPrüfung der Vorder- und Hinterflaps Prüfung der rückschaltbaren Sicherungen PRÜFUNG/ERSETZUNG/RÜCKSCHALTUNG DER SicherungenPrüfung/Ersetzung der Flachsicherungen EinbauVerschrottung FehlersucheFehler Mögliche Ursache Lösung Table DES Matieres IntroductionIntroduction Modifications ET Ameliorations Autres Manuels DE ReferencePieces DE Rechange ET Entretien Capacites OperationnellesDeballage / Livraison Symboles UtilisesSecurite Instructions Generales Français Manuel Dutilisation Description DE LA Machine Structure DE LA MachineStructure DE LA Machine suite Tableau DE Bord ET Commandes Accessoires / OptionsCaracteristiques Techniques Légende Schema ElectriqueCodes des couleurs Schema Electrique suite Utilisation Controle / Preparation DES Batteries SUR UNE Machine NeuveMise EN Marche ET Arret DE LA Machine Avant LA Mise EN MarcheMise en marche de la machine Machine AU Travail Arrêt de la machineEntretien Les Plan Dentretien ProgrammeLors de la Toutes Procédure HeuresControle ET Reglage DE LA Hauteur DU Balai Central Remplacement DU Balai Central Remplacement DES Balais Lateraux Controle ET Reglage DE LA Hauteur DES Balais LaterauxNettoyage ET Controle DE Lintegrite DU Filtre a Poussiere Contrôle des volets latéraux Controle DE LA Hauteur ET DU Fonctionnement DES VoletsContrôle des volets avant et arrière Contrôle des fusibles restaurables Controle / Remplacement Retablissement DES FusiblesContrôle / remplacement des fusibles à lamelle ReposeMise EN Decharge Depistage DES PannesProblème Cause probable Remède Table of Contents Target Manual Purpose and ContentsHOW to Keep this Manual Declaration of Conformity Identification DataChanges and Improvements Spare Parts and MaintenanceOther Reference Manuals Operation CapabilitiesSymbols SafetyUNPACKING/DELIVERY General Instructions English Machine Description Machine StructureMachine Structure Continues ACCESSORIES/OPTIONS Control PanelTechnical Data Key Wiring DiagramColour code Wiring Diagram Continues Battery CHECK/SETTING on a NEW Machine USEStarting and Stopping the Machine Before Starting the MachineStarting the machine Machine Operation Stopping the machineMaintenance Every Procedure Upon delivery 100 200 300 400 Scheduled Maintenance TableHours Main Broom Height Check Adjustment Main Broom Replacement Side Broom Height Check Adjustment Side Broom ReplacementDust Filter Cleaning and Integrity Check Side skirt check Skirt Height and Operation CheckFront and rear skirt check Lamellar fuse check/replacement Hood Safety Switch Operation CheckFuse CHECK/REPLACEMENT/RESET AssemblyScrapping TroubleshootingTrouble Possible cause Remedy Inhoudsopgave InleidingInleiding Modificaties EN Verbeteringen Andere GebruikershandleidingenVervangingsonderdelen EN Onderhoud BedrijfscapaciteitVerpakking VERWIJDEREN/AFLEVERING Gebruikte SymbolenVeiligheid Algemene Instructies Nederlands Gebruiksaanwijzing Beschrijving VAN DE Machine Bouw VAN DE MachineOpbouw VAN DE Machine vervolg Accessoires / Opties Bedieningspaneel EN KnoppenTechnische Eigenschappen Elektrisch Schema KleurcoderingElektrische Installatie vervolg Gebruik Controle / Voorbereidingen Voor Accus OP EEN Nieuwe MachineDE Machine Starten EN Stoppen Voor HET Starten VAN DE MachineStarten van de machine Machine in Bedrijf De machine stoppenOnderhoud Onderhoudsschema Procedure Bij aflevering ElkeDE Hoogte VAN DE Hoofdborstel Controleren EN Afstellen DE Hoofdborstelvervangen DE Hoogte VAN DE Zijborstels Controleren EN Afstellen DE Zijborstels VervangenReiniging EN Contole OP Integriteit VAN HET Stoffilter Controle van de zijflaps Controle VAN DE Hoogte EN Werking VAN DE FlapsControle van de voor- en achterflap Controle van de herbruikbare zekeringen Controle / Vervanging / Resetten VAN DE ZekeringenControle/vervanging van de smeltzekeringen MontageVerwijdering Storingen LokaliserenProbleem Waarschijnlijke oorzaak Oplossing

SR 1100S specifications

The Nilfisk-Advance America SR 1100S is a robust, versatile scrubber designed to meet the diverse cleaning needs of various commercial environments. Ideal for both small and medium-sized spaces, this machine excels in performance, efficiency, and ease of use, making it an excellent choice for businesses looking to achieve a high standard of cleanliness.

One of the standout features of the SR 1100S is its compact and ergonomic design. This allows for easy maneuverability in tight spaces such as aisles, smaller retail environments, and crowded areas. The machine is equipped with a highly efficient brush system that ensures effective scrubbing while reducing water and detergent consumption, enabling operators to achieve optimal results while also being environmentally conscious.

The SR 1100S is powered by a reliable battery system that offers an impressive run time. This allows for extended cleaning sessions without the need for frequent recharging, which can be a significant advantage in busy commercial settings. Additionally, the scrubber features a simple control panel, making it user-friendly for operators of varying skill levels. The intuitive design means that staff can quickly learn to operate the machine, enhancing productivity throughout the organization.

One of the key technologies employed in the Nilfisk-Advance America SR 1100S is the advanced Ecoflex system. This innovative technology enables users to adjust the water and detergent flow according to the specific cleaning needs of each task. This not only helps in conserving resources but also ensures that surfaces are cleaned effectively, regardless of the level of soiling.

Furthermore, the SR 1100S is designed with operator safety in mind. With features that reduce noise levels during operation, it makes it suitable for use in noise-sensitive areas, such as schools and hospitals. The scrubber is also built with maintenance accessibility in mind, allowing for quick and easy servicing, which minimizes downtime.

In conclusion, the Nilfisk-Advance America SR 1100S is a powerful, efficient, and user-friendly scrubber that is backed by advanced technology. Its compact design, effective cleaning capabilities, and operator-friendly features make it a valuable addition to any cleaning fleet. With its commitment to sustainability and efficiency, the SR 1100S is an ideal choice for businesses aiming to maintain a clean and safe environment for employees and customers alike.
Top Page Image Contents