Wayne-Dalton 3221C, 3324B, 3320B Mounting Door Bracket, Installing Light, Manufacturer for Proper

Page 11

	6	Mounting Door Bracket
		Mounting Door Bracket

	Tools Needed:	NOTE: If you have a 5120, 5140, 9100,
		9400, 9600, 9700 or 9800 series door,
	7/16” Socket	do not install this door bracket, install the
		door bracket supplied with the door, see the
	Ratchet Wrench	Installation Instructions and Owner’s Manual
	Ratchet Wrench	supplied with the door. Instructions manuals
		supplied with the door. Instructions manuals
		are available for download at www.wayne-
		dalton.com or call 1-888-827-3667.
		IMPORTANT: DOORS MAY NEED TO BE
		REINFORCED TO PREVENT DAMAGE TO THE
		DOOR. CHECK WITH THE GARAGE DOOR
		MANUFACTURER FOR PROPER
		REINFORCING OF YOUR DOOR.
		For wood doors, mount door bracket,
		using two 1/4”-20 x 2” carriage bolts and
		1/4” locking nuts supplied, on center line of
		door with middle hole in line with top rollers.
		For metal doors, mount door bracket,
		using two 1/4”-20 x 5/8” self drilling screws
		supplied, on center line of door with middle
		hole in line with top rollers.

Reinforce Door Vertically and

Horizontally

Top Roller

Guideline

Door Center

Line

Door Center

Line

1/4”-20 x 2” Carriage Bolts

Top Roller

Guideline1/4”

Locking Nuts

	Top Roller	1/4”-20 x 1/2”	WOOD	Door
			DOORS
	Guideline	Self Drilling Screws		Bracket

STEEL Door

DOORS Bracket

7	Installing Light
	Installing Light

Tools Needed:	Remove lens by pressing up on both sides
	of the bottom of the lens at the junction of
None	the housing, releasing the locking tabs, and
	pulling forward.
	Screw a 60 watt (Maximum) bulb into
	socket. For maximum bulb life, “rough
	service” bulbs are recommended.
	Align the top and bottom tabs on the lens
	with the housing and push straight on until
	lens locks in place.

Housing		Bulb - 60 Watt
		Maximum
		(Not Supplied)

Socket

Locking Tabs

Lens

PRE-OPERATION

Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need 5 You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com

Image 11

Contents Rev.3 7/19/2007 Important NoticeGarage Doors & Openers Package Contents Page Door Test Two Pre-InstallationDisconnect from power source and proceed to assembly Door Test OneHomelink Compatibility Rolling Code Technology System FeaturesTools Needed Deﬁnition of key words used in this manual Table of ContentsAttaching Opener to Rail InstallationReinforce the Header Wall Positioning and Installing Front Wall BracketService Person AT Least 3 Feet Long Positioning MotorEnd of Opener Attach Unit to Front Wall BracketMounting Opener End Proper InstallationReinforcing of Your Door Installing LightMounting Door Bracket Manufacturer for ProperGarage Door Wired Wall Station Installation If IncludedDoor can be Seen When Wall Station Near or Next toChildren and in a Location Where Wall Station Installation If IncludedWall Station Near or Next to Garage Door Wall Station OUT of the ReachNot adhere EntrapmentApply entrapment warning label in a Wired Infrared Safety Sensor Installation Sensor to Opener Installation of Wiring for WiredInfrared Safety Sensor Connecting Wired Infrared SafetyCord in Anyway Connecting OpenerConnecting Trolley To Latch AssemblyFully Closed Position Alignment of Wired InfraredSafety Sensors Be Closed by ContinuouslyTo Avoid Possible Injury or Setting Trolley Close PositionARM Connecting Door Arm to Door Setting Door Opening Travel Setting Door Close TravelStop Bolt Trolley Opener Result from Operating the DOOR/OPENER Contact Obstruction TestFatal Injury MAY Result To Prevent Door Damage or Programming Wireless KeylessEntry If Included Possible Personal InjuryMaterials Important Install ALL WallWood framing using the two screws Surface inside garageInstructions Illustrated Power ConnectionTo Avoid Electrical Shock Important Check Your Local14 x 5/8 self tapping screws as shown in FIG Optional InstallationsTools Needed Power Drill Socket Driver Mounting Door Bracket To Series Door1/4 14 x 5/8 self-tapping screws Must be Adjusted ProperlyShown in FIG With StepStandard Lift Radius Being UsedTrack LOW HeadroomDIM Type of ARM Connecting Door ArmHave to cut straight arm to accomplish Trolley settingsDetermine the WAYNE-DALTON Track Radius Being Used Distance forward To Door , onLOW Headroom Trolley Positioning Chart for Door activation OperationRead and Follow ALL Instructions Operating the Wireless Wall Station Opener Controls Customizing the SettingsTeaching HomeLink to the opener Primary Programming for HomeLink to the ProdriveProgramming/Training HomeLink Unit Alternate Programming for HomeLink to the Prodrive Opening Force Adjustment AdjustmentsAdjustment # 1 Opening and Closing Force Closing Force AdjustmentWall Station Tools Needed NoneTransmitter Twice a Year MaintenanceBattery Replacement for Wall Station Symptom Probable Cause Corrective Action TroubleshootingMAINTENANCE/ Troubleshooting # Per Unit Parts Breakdown Rail Assembly All ModelsDescription Description # Per Unit Parts Breakdown Opener Assembly And Accessories All ModelsWireless Keyless Entry Prodrive AccessoriesPre-drill 5/64 pilot hole Pre-drill 3/32 pilot holeDrill Template Thank you for your purchase Please Do Not Return This Product To The StoreReplacement labor Lifetime Limited WarrantyFCC and IC Statement Patent Information