Wayne-Dalton 3324B, 3322B-Z, 3320B, 3224C-Z, 3222C, 3220C Attaching Opener to Rail, Installation

Page 7

1Attaching Opener to Rail

Tools Needed:	IMPORTANT: THE DRIVER GEAR IN THE
	OPENER MUST BE PROPERLY ALIGNED
3/8” Socket	WITH THE SPROCKET/ COUPLING COGS IN
	THE RAIL ASSEMBLY AND THE MOUNTING
Ratchet Wrench	BOLTS FULLY TIGHTENED, BEFORE
	POWERING UP THE OPENER. NEGLECTING
	TO DO THIS WILL RESULT IN GEAR FAILURE.
	Before assembly, align sprocket/ coupling
	cogs to match notches of driver gear. Rotate
	the motor spline to position driver gear so
	the nearest notch in driver gear is directly
	behind motor spline, as illustrated.
	NOTE: Do not rotate more than 1/2 turn.

Rail Bottom	Sprocket / Coupling Cogs
(Facing Upwards)

Notches

INSTALLATION

Place opposite end of rail on temporary

support approximately 6” in height.

Proceed with attaching rail to opener,

ensuring proper engagement between

sprocket/coupling cogs and driver gear

notches. Realign if necessary, making sure

to keep any rotation only to the nearest

notch. Using the (4) pre-attached

1/4”-20 x 5/8” hex head bolts, assemble

rail to opener using 3/8” socket; tighten

securely.

NOTE: Do not plug the opener power cord

into electrical outlet until opener is fully

installed and you are instructed to do so in

this manual.

Opener

Top View

Motor Spline

Driver Gear

Opener

Sprocket / Coupling Cogs

Notches

1/4” - 20 x 5/8” Hex Head Bolts

Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need 1 You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com

Image 7

Contents Garage Doors & Openers Important NoticeRev.3 7/19/2007 Package Contents Page Door Test Two Pre-InstallationDisconnect from power source and proceed to assembly Door Test OneTools Needed System FeaturesHomelink Compatibility Rolling Code Technology Deﬁnition of key words used in this manual Table of ContentsAttaching Opener to Rail InstallationService Person Positioning and Installing Front Wall BracketReinforce the Header Wall AT Least 3 Feet Long Positioning MotorEnd of Opener Attach Unit to Front Wall BracketMounting Opener End Proper InstallationReinforcing of Your Door Installing LightMounting Door Bracket Manufacturer for ProperGarage Door Wired Wall Station Installation If IncludedDoor can be Seen When Wall Station Near or Next toChildren and in a Location Where Wall Station Installation If IncludedWall Station Near or Next to Garage Door Wall Station OUT of the ReachApply entrapment warning label in a EntrapmentNot adhere Wired Infrared Safety Sensor Installation Sensor to Opener Installation of Wiring for WiredInfrared Safety Sensor Connecting Wired Infrared SafetyCord in Anyway Connecting OpenerConnecting Trolley To Latch AssemblyFully Closed Position Alignment of Wired InfraredSafety Sensors Be Closed by ContinuouslyARM Setting Trolley Close PositionTo Avoid Possible Injury or Connecting Door Arm to Door Setting Door Opening Travel Setting Door Close TravelStop Bolt Trolley Opener Fatal Injury MAY Result Contact Obstruction TestResult from Operating the DOOR/OPENER To Prevent Door Damage or Programming Wireless KeylessEntry If Included Possible Personal InjuryMaterials Important Install ALL WallWood framing using the two screws Surface inside garageInstructions Illustrated Power ConnectionTo Avoid Electrical Shock Important Check Your Local14 x 5/8 self tapping screws as shown in FIG Optional InstallationsTools Needed Power Drill Socket Driver Mounting Door Bracket To Series Door1/4 14 x 5/8 self-tapping screws Must be Adjusted ProperlyShown in FIG With StepStandard Lift Radius Being UsedTrack LOW HeadroomDIM Type of ARM Connecting Door ArmHave to cut straight arm to accomplish Trolley settingsDetermine the WAYNE-DALTON Track Radius Being Used Distance forward To Door , onLOW Headroom Trolley Positioning Chart for Read and Follow ALL Instructions OperationDoor activation Operating the Wireless Wall Station Opener Controls Customizing the SettingsProgramming/Training HomeLink Unit Primary Programming for HomeLink to the ProdriveTeaching HomeLink to the opener Alternate Programming for HomeLink to the Prodrive Opening Force Adjustment AdjustmentsAdjustment # 1 Opening and Closing Force Closing Force AdjustmentTransmitter Tools Needed NoneWall Station Battery Replacement for Wall Station MaintenanceTwice a Year MAINTENANCE/ Troubleshooting TroubleshootingSymptom Probable Cause Corrective Action Description Parts Breakdown Rail Assembly All Models# Per Unit Description # Per Unit Parts Breakdown Opener Assembly And Accessories All ModelsWireless Keyless Entry Prodrive AccessoriesDrill Template Pre-drill 3/32 pilot holePre-drill 5/64 pilot hole Thank you for your purchase Please Do Not Return This Product To The StoreReplacement labor Lifetime Limited WarrantyFCC and IC Statement Patent Information