Wayne-Dalton 3322B Connecting Opener, Connecting Trolley, To Latch Assembly, Cord in Anyway

Page 17

14			Connecting Opener

			To Outlet

Tools Needed:
			WARNING

None	TO REDUCE THE RISK OF ELECTRICAL
	SHOCK, DO NOT CHANGE THE POWER
	CORD IN ANYWAY.
	IMPORTANT: THE OPENER MUST BE
	CONNECTED TO A PROPERLY GROUNDED 3
	PRONG, 120 VOLT OUTLET.
	The opener can be permanently wired. To
	permanently wire the unit, see permanent
	wiring option on page 20.
	Plug the power cord into the closest
	grounding type receptacle. Excess power
	cord length must be routed and contained
	safely away from any moving parts.
	As soon as power is applied to the opener,
	the light on the opener will blink once to
	indicate a successful self-check of the
	controls.

Outlet

Power Cord

15	Connecting Trolley
	Connecting Trolley
	To Latch Assembly

Tools Needed:	Slide the trolley until it snaps onto the latch
	assembly.
None
	Attach warning label to the red release cord.
	Thread the red release cord through the pull
	knob so knot is inside pull knob. Tie a double
	knot at the end of the red release cord to
	secure pull knob.
	NOTE: Pull knob should hang 6 feet above
	floor. Ensure that the rope and handle clear
	the tops of all vehicles to avoid
	entanglement.

Trolley

Upper Door Arm

Tag

	Trolley	Release Cord
Latch Assembly		Release Cord
Latch Assembly

Pull Knob

Use a Double Knot

To Secure The Red

Pull Knob

Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need 11 You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com

Image 17

Contents Rev.3 7/19/2007 Important NoticeGarage Doors & Openers Package Contents Page Disconnect from power source and proceed to assembly Pre-InstallationDoor Test One Door Test TwoHomelink Compatibility Rolling Code Technology System FeaturesTools Needed Deﬁnition of key words used in this manual Table of ContentsAttaching Opener to Rail InstallationReinforce the Header Wall Positioning and Installing Front Wall BracketService Person End of Opener Positioning MotorAttach Unit to Front Wall Bracket AT Least 3 Feet LongMounting Opener End Proper InstallationMounting Door Bracket Installing LightManufacturer for Proper Reinforcing of Your DoorDoor can be Seen When Wired Wall Station Installation If IncludedWall Station Near or Next to Garage DoorWall Station Near or Next to Garage Door Wall Station Installation If IncludedWall Station OUT of the Reach Children and in a Location WhereNot adhere EntrapmentApply entrapment warning label in a Wired Infrared Safety Sensor Installation Infrared Safety Sensor Installation of Wiring for WiredConnecting Wired Infrared Safety Sensor to OpenerConnecting Trolley Connecting OpenerTo Latch Assembly Cord in AnywaySafety Sensors Alignment of Wired InfraredBe Closed by Continuously Fully Closed PositionTo Avoid Possible Injury or Setting Trolley Close PositionARM Connecting Door Arm to Door Setting Door Opening Travel Setting Door Close TravelStop Bolt Trolley Opener Result from Operating the DOOR/OPENER Contact Obstruction TestFatal Injury MAY Result Entry If Included Programming Wireless KeylessPossible Personal Injury To Prevent Door Damage orWood framing using the two screws Important Install ALL WallSurface inside garage MaterialsTo Avoid Electrical Shock Power ConnectionImportant Check Your Local Instructions IllustratedTools Needed Power Drill Socket Driver Optional InstallationsMounting Door Bracket To Series Door 14 x 5/8 self tapping screws as shown in FIGShown in FIG Must be Adjusted ProperlyWith Step 1/4 14 x 5/8 self-tapping screwsTrack Radius Being UsedLOW Headroom Standard LiftDIM Type of ARM Connecting Door ArmDetermine the WAYNE-DALTON Track Radius Being Used Trolley settingsDistance forward To Door , on Have to cut straight arm to accomplishLOW Headroom Trolley Positioning Chart for Door activation OperationRead and Follow ALL Instructions Operating the Wireless Wall Station Opener Controls Customizing the SettingsTeaching HomeLink to the opener Primary Programming for HomeLink to the ProdriveProgramming/Training HomeLink Unit Alternate Programming for HomeLink to the Prodrive Adjustment # 1 Opening and Closing Force AdjustmentsClosing Force Adjustment Opening Force AdjustmentWall Station Tools Needed NoneTransmitter Twice a Year MaintenanceBattery Replacement for Wall Station Symptom Probable Cause Corrective Action TroubleshootingMAINTENANCE/ Troubleshooting # Per Unit Parts Breakdown Rail Assembly All ModelsDescription Description # Per Unit Parts Breakdown Opener Assembly And Accessories All ModelsWireless Keyless Entry Prodrive AccessoriesPre-drill 5/64 pilot hole Pre-drill 3/32 pilot holeDrill Template Thank you for your purchase Please Do Not Return This Product To The StoreReplacement labor Lifetime Limited WarrantyFCC and IC Statement Patent Information