Wayne-Dalton 3324B, 3322B-Z Wall Station Installation If Included, Wall Station OUT of the Reach

Page 13

9	Deluxe Multi-Function Wireless
	Wall Station Installation
	(If Included)
Tools Needed:	WARNING
	WARNING
Power Drill	TO PREVENT POSSIBLE INJURY, INSTALL
	WALL STATION OUT OF THE REACH OF		Wall Station
3/32” Drill Bit	CHILDREN AND IN A LOCATION WHERE
	THE DOOR CAN BE SEEN WHEN THE
Phillips Head	OPENER IS ACTIVATED. DO NOT MOUNT
Screwdriver	WALL STATION NEAR OR NEXT TO
	GARAGE DOOR.		5 Foot
			Minimum
	NOTE: For proper operation, mount the wall
	station on a flat surface.
	The wall station can be mounted to a NEMA
	standard electrical box or directly to any wall
	surface. No wiring is required.
	Locate wall station adjacent to service
	entrance door at a minimum height of 5 ft.,
	and at least 6 ft. away from garage door.	Lower Screw Installation	Upper Screw Installation
	If mounting to a NEMA electrical box, use
	machine thread screws provided in place of the
	wood screws. No drilling is required. If high
	voltage wiring is contained in the box,
	a standard NEMA solid faceplate must be
	installed between the box and the wall station. If
	fastening into drywall or concrete, use anchors
	provided. When mounting to wood use a 3/32"
	drill bit and the drilling template located on
	page 39. Drill the two 3/32” mounting holes
	using the drill template. Drill 3/16" holes if
	using anchors.		Phillips
			Head Screw
	Install lower screw leaving 7/16" of the screw
	exposed. Slide wall station keyhole slot onto the
	lower phillips head screw. Wall station should	Phillips Head
	slide onto screw, providing a snug fit. If	Screw
	necessary remove wall station and loosen or
	tighten lower phillips head screw until a snug fit
	is achieved.	7/16”
		7/16”
	Once wall station is fitted on lower screw, install
	upper screw. Do not over-tighten.	Keyhole
		Keyhole
	CAUTION: Over tightening the upper screw	Slot
	CAUTION: Over tightening the upper screw
	could deform plastic case.
		Phillips
		Head Screw

Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need 7 You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com

Image 13

Contents Garage Doors & Openers Important NoticeRev.3 7/19/2007 Package Contents Page Disconnect from power source and proceed to assembly Pre-InstallationDoor Test One Door Test TwoTools Needed System FeaturesHomelink Compatibility Rolling Code Technology Deﬁnition of key words used in this manual Table of ContentsAttaching Opener to Rail InstallationService Person Positioning and Installing Front Wall BracketReinforce the Header Wall End of Opener Positioning MotorAttach Unit to Front Wall Bracket AT Least 3 Feet LongMounting Opener End Proper InstallationMounting Door Bracket Installing LightManufacturer for Proper Reinforcing of Your DoorDoor can be Seen When Wired Wall Station Installation If IncludedWall Station Near or Next to Garage DoorWall Station Near or Next to Garage Door Wall Station Installation If IncludedWall Station OUT of the Reach Children and in a Location WhereApply entrapment warning label in a EntrapmentNot adhere Wired Infrared Safety Sensor Installation Infrared Safety Sensor Installation of Wiring for WiredConnecting Wired Infrared Safety Sensor to OpenerConnecting Trolley Connecting OpenerTo Latch Assembly Cord in AnywaySafety Sensors Alignment of Wired InfraredBe Closed by Continuously Fully Closed PositionARM Setting Trolley Close PositionTo Avoid Possible Injury or Connecting Door Arm to Door Setting Door Opening Travel Setting Door Close TravelStop Bolt Trolley Opener Fatal Injury MAY Result Contact Obstruction TestResult from Operating the DOOR/OPENER Entry If Included Programming Wireless KeylessPossible Personal Injury To Prevent Door Damage orWood framing using the two screws Important Install ALL WallSurface inside garage MaterialsTo Avoid Electrical Shock Power ConnectionImportant Check Your Local Instructions IllustratedTools Needed Power Drill Socket Driver Optional InstallationsMounting Door Bracket To Series Door 14 x 5/8 self tapping screws as shown in FIGShown in FIG Must be Adjusted ProperlyWith Step 1/4 14 x 5/8 self-tapping screwsTrack Radius Being UsedLOW Headroom Standard LiftDIM Type of ARM Connecting Door ArmDetermine the WAYNE-DALTON Track Radius Being Used Trolley settingsDistance forward To Door , on Have to cut straight arm to accomplishLOW Headroom Trolley Positioning Chart for Read and Follow ALL Instructions OperationDoor activation Operating the Wireless Wall Station Opener Controls Customizing the SettingsProgramming/Training HomeLink Unit Primary Programming for HomeLink to the ProdriveTeaching HomeLink to the opener Alternate Programming for HomeLink to the Prodrive Adjustment # 1 Opening and Closing Force AdjustmentsClosing Force Adjustment Opening Force AdjustmentTransmitter Tools Needed NoneWall Station Battery Replacement for Wall Station MaintenanceTwice a Year MAINTENANCE/ Troubleshooting TroubleshootingSymptom Probable Cause Corrective Action Description Parts Breakdown Rail Assembly All Models# Per Unit Description # Per Unit Parts Breakdown Opener Assembly And Accessories All ModelsWireless Keyless Entry Prodrive AccessoriesDrill Template Pre-drill 3/32 pilot holePre-drill 5/64 pilot hole Thank you for your purchase Please Do Not Return This Product To The StoreReplacement labor Lifetime Limited WarrantyFCC and IC Statement Patent Information