Wayne-Dalton 3324B, 3322B-Z, 3320B, 3224C-Z, 3222C Tools Needed None, Transmitter, Wall Station

Page 39

I

Tools Needed:

None

Programming Wireless Wall Station(s)

Or Transmitter(s) to Opener

WARNING

DURING PROGRAMMING THE GARAGE DOOR MAY OPERATE. KEEP PEOPLE AND OBJECTS CLEAR OF THE MOVING DOOR TO PREVENT DOOR DAMAGE OR POSSIBLE PERSONAL INJURY.

NOTE: Programming failure can occur if the wall station or transmitter is too close to the opener during the programming sequence. There must be a minimum of 6 feet between the wall station/ transmitter and the opener.

NOTE: The opener can be activated by up to 8 remote transmitters, 2 wall stations and 2 keyless entries. If a 9th remote is programmed the first remote programmed will be lost from memory. The same is true if a third wall station or a third keyless entry is programmed, the first will no longer be in memory and will not operate the opener.

NOTE: Do not press any button on the wall station or transmitter until instructed.

TRANSMITTER:

1.Press and release the PROGRAM button located on the garage door opener. The red PROGRAM STATUS light on the opener unit and the overhead lamp will turn on and remain lit for one minute, indicating activation of the learn mode.

2.Press one of the buttons on the transmitter you wish to use to operate the door. The PROGRAM STATUS light on the opener will turn on and off three times indicating a successful learn.

3.Press the same button on the transmitter once more to confirm operation. The opener will turn on and move the door.

At this point you will be able to activate the opener.

WALL STATION:

1.Press and release the PROGRAM button located on the garage door opener. The red PROGRAM STATUS light on the opener unit and the overhead lamp will turn on and remain lit for one minute, indicating activation of the learn mode.

2.Press the light on/off button on the wall station. The program status light will turn on and off three times indicating a successful learn.

3.Press the light on/off button on the wall station once more to confirm operation. The overhead light will toggle from on to off and from off to on.

At this point you will be able to activate the opener.

Right Side Of Opener

		Program Status
		LED
Program	PROGRAM	SW STATUS
Program
Button
		FORCE ADJ.

Large Button

Transmitter

Light

Button

			r
		e at
	p			e
o	O			D
				D
				o
T				o

Pressr

Here

Wall Station

Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need 33 You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com

Image 39

Contents Important Notice Garage Doors & OpenersRev.3 7/19/2007 Package Contents Page Door Test Two Pre-InstallationDisconnect from power source and proceed to assembly Door Test OneSystem Features Tools NeededHomelink Compatibility Rolling Code Technology Deﬁnition of key words used in this manual Table of ContentsAttaching Opener to Rail InstallationPositioning and Installing Front Wall Bracket Service PersonReinforce the Header Wall AT Least 3 Feet Long Positioning MotorEnd of Opener Attach Unit to Front Wall BracketMounting Opener End Proper InstallationReinforcing of Your Door Installing LightMounting Door Bracket Manufacturer for ProperGarage Door Wired Wall Station Installation If IncludedDoor can be Seen When Wall Station Near or Next toChildren and in a Location Where Wall Station Installation If IncludedWall Station Near or Next to Garage Door Wall Station OUT of the ReachEntrapment Apply entrapment warning label in aNot adhere Wired Infrared Safety Sensor Installation Sensor to Opener Installation of Wiring for WiredInfrared Safety Sensor Connecting Wired Infrared SafetyCord in Anyway Connecting OpenerConnecting Trolley To Latch AssemblyFully Closed Position Alignment of Wired InfraredSafety Sensors Be Closed by ContinuouslySetting Trolley Close Position ARMTo Avoid Possible Injury or Connecting Door Arm to Door Setting Door Opening Travel Setting Door Close TravelStop Bolt Trolley Opener Contact Obstruction Test Fatal Injury MAY ResultResult from Operating the DOOR/OPENER To Prevent Door Damage or Programming Wireless KeylessEntry If Included Possible Personal InjuryMaterials Important Install ALL WallWood framing using the two screws Surface inside garageInstructions Illustrated Power ConnectionTo Avoid Electrical Shock Important Check Your Local14 x 5/8 self tapping screws as shown in FIG Optional InstallationsTools Needed Power Drill Socket Driver Mounting Door Bracket To Series Door1/4 14 x 5/8 self-tapping screws Must be Adjusted ProperlyShown in FIG With StepStandard Lift Radius Being UsedTrack LOW HeadroomDIM Type of ARM Connecting Door ArmHave to cut straight arm to accomplish Trolley settingsDetermine the WAYNE-DALTON Track Radius Being Used Distance forward To Door , onLOW Headroom Trolley Positioning Chart for Operation Read and Follow ALL InstructionsDoor activation Operating the Wireless Wall Station Opener Controls Customizing the SettingsPrimary Programming for HomeLink to the Prodrive Programming/Training HomeLink UnitTeaching HomeLink to the opener Alternate Programming for HomeLink to the Prodrive Opening Force Adjustment AdjustmentsAdjustment # 1 Opening and Closing Force Closing Force AdjustmentTools Needed None TransmitterWall Station Maintenance Battery Replacement for Wall StationTwice a Year Troubleshooting MAINTENANCE/ TroubleshootingSymptom Probable Cause Corrective Action Parts Breakdown Rail Assembly All Models Description# Per Unit Description # Per Unit Parts Breakdown Opener Assembly And Accessories All ModelsWireless Keyless Entry Prodrive AccessoriesPre-drill 3/32 pilot hole Drill TemplatePre-drill 5/64 pilot hole Thank you for your purchase Please Do Not Return This Product To The StoreReplacement labor Lifetime Limited WarrantyFCC and IC Statement Patent Information