Wayne-Dalton Guide to Setting Trolley Close Position for Prodrive Garage Door Openers

Page 19

17

 

Setting Trolley Close Position

Tools Needed:

 

 

 

 

 

 

WARNING

 

 

 

 

 

Pliers/Wire Cutters

TO AVOID POSSIBLE INJURY OR

 

PROPERTY DAMAGE, KEEP PEOPLE AND

Tape Measure

OBJECTS CLEAR OF THE MOVING DOOR

 

ARM.

Flat Tip

NOTE: If necessary, activate the opener

Screwdriver

 

to move the trolley/ upper door arm to the

 

closed position.

 

NOTE: If you have a 9100, 9400,9600,

 

5120, 5140 or 9700 series door, with one of

 

the door brackets shown at the right and a

 

Torquemaster® or Extension Spring(s)

 

counterbalance system, see “Setting Trolley

 

Close Position/ Connecting Door Arm To

 

Door” on pages 23-24. If not, complete this

 

step.

 

NOTE: If you have a 9100, 9400, 9600,

 

5120, 5140 or 9700 series door, with one of

 

the door brackets shown at the right and a

 

Torsion Spring(s), see “Setting Trolley Close

 

Position/ Connecting Door Arm To Door” on

 

pages 25-26. If not, complete this step.

 

Trolley and latch assembly must be at the

 

factory preset fully closed position, (see

 

illustration).

 

Verify preliminary trolley and latch assembly

 

close position is 11” to 13” between trolley

 

clevis pin and the inside face of the door.

 

If adjustment of the trolley/latch assembly

 

position is required, use the close travel

 

adjustment screw located on the bottom of

 

the opener. A 1/4 turn equals approximately

 

1” of trolley travel; turn clockwise to de-

 

crease distance between header and trolley

 

and counter-clockwise to increase distance

 

between header and trolley.

 

 

 

 

 

 

Single and Double Tab Door Brackets

 

Models: 9100, 9400, 9600, 5120 and 5140.

Model: 9700

Double Tab

Single Tab

Double Tab

Single Tab

Bracket

Bracket

Bracket

Bracket

 

11” to 13”

 

 

 

(13” Minimum

 

 

 

For Belt Drive)

 

 

 

 

Trolley

 

 

 

(Closed Limit Position)

 

Door Bracket

Upper Arm

 

 

 

Tag

 

 

Release Cord

 

 

 

 

Pull Knob

 

TRAVEL ADJUSTMENT

 

 

OPEN

CLOSE

Bottom Of Opener

 

LESS

MORE

 

 

MORE

 

 

Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need 13 You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com

Image 19
Contents Garage Doors & Openers Important NoticeRev.3 7/19/2007 Package Contents Page Door Test Two Pre-InstallationDisconnect from power source and proceed to assembly Door Test OneTools Needed System FeaturesHomelink Compatibility Rolling Code Technology Definition of key words used in this manual Table of ContentsAttaching Opener to Rail InstallationService Person Positioning and Installing Front Wall BracketReinforce the Header Wall AT Least 3 Feet Long Positioning MotorEnd of Opener Attach Unit to Front Wall BracketMounting Opener End Proper InstallationReinforcing of Your Door Installing LightMounting Door Bracket Manufacturer for ProperGarage Door Wired Wall Station Installation If IncludedDoor can be Seen When Wall Station Near or Next toChildren and in a Location Where Wall Station Installation If IncludedWall Station Near or Next to Garage Door Wall Station OUT of the ReachApply entrapment warning label in a EntrapmentNot adhere Wired Infrared Safety Sensor Installation Sensor to Opener Installation of Wiring for WiredInfrared Safety Sensor Connecting Wired Infrared SafetyCord in Anyway Connecting OpenerConnecting Trolley To Latch AssemblyFully Closed Position Alignment of Wired InfraredSafety Sensors Be Closed by ContinuouslyARM Setting Trolley Close PositionTo Avoid Possible Injury or Connecting Door Arm to Door Setting Door Opening Travel Setting Door Close TravelStop Bolt Trolley Opener Fatal Injury MAY Result Contact Obstruction TestResult from Operating the DOOR/OPENER To Prevent Door Damage or Programming Wireless KeylessEntry If Included Possible Personal InjuryMaterials Important Install ALL WallWood framing using the two screws Surface inside garageInstructions Illustrated Power ConnectionTo Avoid Electrical Shock Important Check Your Local14 x 5/8 self tapping screws as shown in FIG Optional InstallationsTools Needed Power Drill Socket Driver Mounting Door Bracket To Series Door1/4 14 x 5/8 self-tapping screws Must be Adjusted ProperlyShown in FIG With StepStandard Lift Radius Being UsedTrack LOW HeadroomDIM Type of ARM Connecting Door ArmHave to cut straight arm to accomplish Trolley settingsDetermine the WAYNE-DALTON Track Radius Being Used Distance forward To Door , onLOW Headroom Trolley Positioning Chart for Read and Follow ALL Instructions OperationDoor activation Operating the Wireless Wall Station Opener Controls Customizing the SettingsProgramming/Training HomeLink Unit Primary Programming for HomeLink to the ProdriveTeaching HomeLink to the opener Alternate Programming for HomeLink to the Prodrive Opening Force Adjustment AdjustmentsAdjustment # 1 Opening and Closing Force Closing Force AdjustmentTransmitter Tools Needed NoneWall Station Battery Replacement for Wall Station MaintenanceTwice a Year MAINTENANCE/ Troubleshooting  TroubleshootingSymptom Probable Cause Corrective Action Description Parts Breakdown Rail Assembly All Models# Per Unit Description # Per Unit Parts Breakdown Opener Assembly And Accessories All ModelsWireless Keyless Entry Prodrive AccessoriesDrill Template Pre-drill 3/32 pilot holePre-drill 5/64 pilot hole Thank you for your purchase Please Do Not Return This Product To The StoreReplacement labor Lifetime Limited WarrantyFCC and IC Statement Patent Information