Wayne-Dalton 3221C Programming Wireless Keyless, Entry If Included, Possible Personal Injury

Page 24

23

 

Programming Wireless Keyless

 

 

 

 

 

Entry (If Included)

 

 

 

 

 

Tools Needed:

 

 

 

 

 

 

WARNING

 

 

 

 

 

None

DURING PROGRAMMING THE GARAGE

 

DOOR MAY OPERATE. KEEP PEOPLE AND

 

OBJECTS CLEAR OF THE MOVING DOOR

 

TO PREVENT DOOR DAMAGE OR

 

POSSIBLE PERSONAL INJURY.

 

NOTE: To simplify installation, program the wire-

 

less keyless entry to the opener before mounting

 

to the wall.

 

NOTE: Before programming ensure garage door

 

is in the “down” position.

1.Press and release the PROGRAM button. The red PROGRAM STATUS light on the opener and the overhead lamp will turn on and remain lit for one minute, indicating that it is ready to learn the keyless entry.

2.Press the desired five digit PIN (PERSONAL IDENTIFICATION NUMBER), example 1-3-8-2-5. The PROGRAM STATUS light will turn on and off three times indicating a successful learn.

NOTE: Do not set a code that presents the num- bers in sequential order, as an example 1/2, 3/4, 5/6, 7/8, 9/0. Studies show that people naturally press the buttons in a sequential pattern. Also, do not select a code that uses the same button five times consecutively. Thieves can easily figure out these types of codes.

NOTE: If at anytime, an error was made entering the code, simultaneously press and release the 7/8 and 9/0 buttons to reset the keyless entry; then repeat programming steps above.

NOTE: A single wireless keyless entry device may be programmed to operate multiple garage door openers. To program additional openers, repeat programming steps using a different five digit PIN for each additional opener.

How Your Keyless Entry Operates Your Door:

The following explains how your Keyless Entry can be used to OPEN, CLOSE, START, and STOP your door.

1.Enter your 5-digit PIN (personal identification number); door will move.

NOTE: If you inadvertently enter an incorrect code, the door will not move. To reset, simultaneously press and release the 7/8 and 9/0 buttons and reenter your PIN number.

2.Unit remains active for next 25 seconds. Pressing any key, will stop the door if opening, and stop or reverse the door if closing during the

25seconds active period.

Right Side Of Opener

Program Status

LED

Program

PROGRAM

SW STATUS

 

 

Button

 

FORCE ADJ.

 

 

Keyless Entry

18Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need

You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Important Notice Garage Doors & OpenersRev.3 7/19/2007 Package Contents Page Pre-Installation Disconnect from power source and proceed to assemblyDoor Test One Door Test TwoSystem Features Tools NeededHomelink Compatibility Rolling Code Technology Table of Contents Definition of key words used in this manualInstallation Attaching Opener to RailPositioning and Installing Front Wall Bracket Service PersonReinforce the Header Wall Positioning Motor End of OpenerAttach Unit to Front Wall Bracket AT Least 3 Feet LongProper Installation Mounting Opener EndInstalling Light Mounting Door BracketManufacturer for Proper Reinforcing of Your DoorWired Wall Station Installation If Included Door can be Seen WhenWall Station Near or Next to Garage DoorWall Station Installation If Included Wall Station Near or Next to Garage DoorWall Station OUT of the Reach Children and in a Location WhereEntrapment Apply entrapment warning label in aNot adhere Wired Infrared Safety Sensor Installation Installation of Wiring for Wired Infrared Safety SensorConnecting Wired Infrared Safety Sensor to OpenerConnecting Opener Connecting TrolleyTo Latch Assembly Cord in AnywayAlignment of Wired Infrared Safety SensorsBe Closed by Continuously Fully Closed PositionSetting Trolley Close Position ARMTo Avoid Possible Injury or Connecting Door Arm to Door Setting Door Close Travel Setting Door Opening TravelStop Bolt Trolley Opener Contact Obstruction Test Fatal Injury MAY ResultResult from Operating the DOOR/OPENER Programming Wireless Keyless Entry If IncludedPossible Personal Injury To Prevent Door Damage orImportant Install ALL Wall Wood framing using the two screwsSurface inside garage MaterialsPower Connection To Avoid Electrical ShockImportant Check Your Local Instructions IllustratedOptional Installations Tools Needed Power Drill Socket DriverMounting Door Bracket To Series Door 14 x 5/8 self tapping screws as shown in FIGMust be Adjusted Properly Shown in FIGWith Step 1/4 14 x 5/8 self-tapping screwsRadius Being Used TrackLOW Headroom Standard LiftConnecting Door Arm DIM Type of ARMTrolley settings Determine the WAYNE-DALTON Track Radius Being UsedDistance forward To Door , on Have to cut straight arm to accomplishLOW Headroom Trolley Positioning Chart for Operation Read and Follow ALL InstructionsDoor activation Operating the Wireless Wall Station Customizing the Settings Opener ControlsPrimary Programming for HomeLink to the Prodrive Programming/Training HomeLink UnitTeaching HomeLink to the opener Alternate Programming for HomeLink to the Prodrive Adjustments Adjustment # 1 Opening and Closing ForceClosing Force Adjustment Opening Force AdjustmentTools Needed None TransmitterWall Station Maintenance Battery Replacement for Wall StationTwice a Year  Troubleshooting MAINTENANCE/ TroubleshootingSymptom Probable Cause Corrective Action Parts Breakdown Rail Assembly All Models Description# Per Unit Parts Breakdown Opener Assembly And Accessories All Models Description # Per UnitProdrive Accessories Wireless Keyless EntryPre-drill 3/32 pilot hole Drill TemplatePre-drill 5/64 pilot hole Please Do Not Return This Product To The Store Thank you for your purchaseLifetime Limited Warranty Replacement laborPatent Information FCC and IC Statement
Top Page Image Contents