Wayne-Dalton 3320B-Z Important Install ALL Wall, Wood framing using the two screws, Materials

Page 25

24

Installing Wireless Keyless Entry

 

 

(If Included)

 

IMPORTANT: INSTALL ALL WALL

Tools Needed:

 

CONTROLS OUT OF THE REACH OF

Power Drill

CHILDREN AND IN A LOCATION WHERE THE

 

DOOR CAN BE SEEN BEFORE ACTIVATING.

5/64” Drill Bit

Locate a convenient place to mount the

 

Phillips Head

wireless keyless entry, that does not

Screwdriver

interfere with the normal opening and

 

closing of the door. To keep keyless entry

 

out of the reach of children, measure and

 

mark a spot at least 5 feet up from the floor.

 

Use the drilling template located on Page 39

 

to determine hole positions. Drill 5/64” pilot

 

holes 3/4” deep at each screw location.

 

Snap open the wireless keyless entry case

 

with a coin. Secure keyless entry base into

 

wood framing using the two screws

 

provided. Snap the front case half back onto

 

the base. Remove paper backing from

 

instruction label and apply to a clean

 

surface inside garage.

 

NOTE: Two screws are included for

 

mounting to wood structures. Ensure proper

 

hardware is used for mounting to other

 

materials.

 

NOTE: After completing this step, continue

 

with page 27.

 

 

Keyless Entry

5’

Keyless Entry Base

Keyless Entry Front

Case

Screws

Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need 19 You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Garage Doors & Openers Important NoticeRev.3 7/19/2007 Package Contents Page Disconnect from power source and proceed to assembly Pre-InstallationDoor Test One Door Test TwoTools Needed System FeaturesHomelink Compatibility Rolling Code Technology Definition of key words used in this manual Table of ContentsAttaching Opener to Rail InstallationService Person Positioning and Installing Front Wall BracketReinforce the Header Wall End of Opener Positioning MotorAttach Unit to Front Wall Bracket AT Least 3 Feet LongMounting Opener End Proper InstallationMounting Door Bracket Installing LightManufacturer for Proper Reinforcing of Your DoorDoor can be Seen When Wired Wall Station Installation If IncludedWall Station Near or Next to Garage DoorWall Station Near or Next to Garage Door Wall Station Installation If IncludedWall Station OUT of the Reach Children and in a Location WhereApply entrapment warning label in a EntrapmentNot adhere Wired Infrared Safety Sensor Installation Infrared Safety Sensor Installation of Wiring for WiredConnecting Wired Infrared Safety Sensor to OpenerConnecting Trolley Connecting OpenerTo Latch Assembly Cord in AnywaySafety Sensors Alignment of Wired InfraredBe Closed by Continuously Fully Closed PositionARM Setting Trolley Close PositionTo Avoid Possible Injury or Connecting Door Arm to Door Setting Door Opening Travel Setting Door Close TravelStop Bolt Trolley Opener Fatal Injury MAY Result Contact Obstruction TestResult from Operating the DOOR/OPENER Entry If Included Programming Wireless KeylessPossible Personal Injury To Prevent Door Damage orWood framing using the two screws Important Install ALL WallSurface inside garage MaterialsTo Avoid Electrical Shock Power ConnectionImportant Check Your Local Instructions IllustratedTools Needed Power Drill Socket Driver Optional InstallationsMounting Door Bracket To Series Door 14 x 5/8 self tapping screws as shown in FIGShown in FIG Must be Adjusted ProperlyWith Step 1/4 14 x 5/8 self-tapping screwsTrack Radius Being UsedLOW Headroom Standard LiftDIM Type of ARM Connecting Door ArmDetermine the WAYNE-DALTON Track Radius Being Used Trolley settingsDistance forward To Door , on Have to cut straight arm to accomplishLOW Headroom Trolley Positioning Chart for Read and Follow ALL Instructions OperationDoor activation Operating the Wireless Wall Station Opener Controls Customizing the SettingsProgramming/Training HomeLink Unit Primary Programming for HomeLink to the ProdriveTeaching HomeLink to the opener Alternate Programming for HomeLink to the Prodrive Adjustment # 1 Opening and Closing Force AdjustmentsClosing Force Adjustment Opening Force AdjustmentTransmitter Tools Needed NoneWall Station Battery Replacement for Wall Station MaintenanceTwice a Year MAINTENANCE/ Troubleshooting  TroubleshootingSymptom Probable Cause Corrective Action Description Parts Breakdown Rail Assembly All Models# Per Unit Description # Per Unit Parts Breakdown Opener Assembly And Accessories All ModelsWireless Keyless Entry Prodrive AccessoriesDrill Template Pre-drill 3/32 pilot holePre-drill 5/64 pilot hole Thank you for your purchase Please Do Not Return This Product To The StoreReplacement labor Lifetime Limited WarrantyFCC and IC Statement Patent Information
Top Page Image Contents