Wayne-Dalton 3220C-Z, 3324B, 3322B-Z, 3320B, 3224C-Z, 3222C Customizing the Settings, Opener Controls

Page 35

I

Customizing the Settings

Custom pet position:

The pet button opens a closed door to a preset position between 8 and 30 inches above the floor, allowing pets to enter and exit the garage without the door being fully open. To change the automatic pet opening height:

Start with the door in the closed position.

1.Operate the door then stop it at the desired height. If desired height is not achieved, the door must be returned to the closed position.

2.Press and release the wall stations program button, or the opener program switch button two times. The status light on the opener unit and the overhead light will flash on and off at a normal rate.

3.Press the pet button. The status light on the opener and the overhead light will flash on and off three times indicating successful programming.

Multi-Door Programming:

Momentarily pressing the button programmed in the transmitter programming step activates the door. Other buttons can also be programmed to activate different doors, for multi-door installations. Each button or a combination of two buttons pressed simultaneously can be programmed to activate a different door. Only one button at a time can be programmed to activate a specific opener.

Up/Down Button

Program Button

I

Opener Controls

 

The program button located on the right side of the opener has several functions.

1.Pressing the program button once, will make the status light and overhead lamp turn on steady. This mode allows programming of transmitters, wireless keyless entry, and wireless wall stations (see page 33).

2.Pressing the program button two times will make the

status light and overhead lamp blink on and off. This mode allows programming of a custom pet position (see “Customizing The Settings” above).

3.Pressing the program button three times will make the

status light and overhead lamp blink on and off with a long pause at each blink cycle. This mode allows programming of the opening force (see page 32).

4.Pressing and holding the program button for 10 seconds

will erase all transmitters, multi-function wall station and wireless keyless entry from memory. The status light and over

head light will blink 3 times indicating a successful erase operation.

Right Side Of Opener

Bottom Of Opener

Program

Button

 

 

Program Status

 

 

LED

PROGRAM

 

SW STATUS

 

ADJ.

Closing

 

 

 

FORCE

Force

 

 

Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need 29 You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com

Page 34 Page 36
Image 35
Page 34 Page 36
Contents Rev.3 7/19/2007 Important NoticeGarage Doors & Openers Package Contents Page Door Test Two Pre-InstallationDisconnect from power source and proceed to assembly Door Test OneHomelink Compatibility Rolling Code Technology System FeaturesTools Needed Definition of key words used in this manual Table of ContentsAttaching Opener to Rail InstallationReinforce the Header Wall Positioning and Installing Front Wall BracketService Person AT Least 3 Feet Long Positioning MotorEnd of Opener Attach Unit to Front Wall BracketMounting Opener End Proper InstallationReinforcing of Your Door Installing LightMounting Door Bracket Manufacturer for ProperGarage Door Wired Wall Station Installation If IncludedDoor can be Seen When Wall Station Near or Next toChildren and in a Location Where Wall Station Installation If IncludedWall Station Near or Next to Garage Door Wall Station OUT of the ReachNot adhere EntrapmentApply entrapment warning label in a Wired Infrared Safety Sensor Installation Sensor to Opener Installation of Wiring for WiredInfrared Safety Sensor Connecting Wired Infrared SafetyCord in Anyway Connecting OpenerConnecting Trolley To Latch AssemblyFully Closed Position Alignment of Wired InfraredSafety Sensors Be Closed by ContinuouslyTo Avoid Possible Injury or Setting Trolley Close PositionARM Connecting Door Arm to Door Setting Door Opening Travel Setting Door Close TravelStop Bolt Trolley Opener Result from Operating the DOOR/OPENER Contact Obstruction TestFatal Injury MAY Result To Prevent Door Damage or Programming Wireless KeylessEntry If Included Possible Personal InjuryMaterials Important Install ALL WallWood framing using the two screws Surface inside garageInstructions Illustrated Power ConnectionTo Avoid Electrical Shock Important Check Your Local14 x 5/8 self tapping screws as shown in FIG Optional InstallationsTools Needed Power Drill Socket Driver Mounting Door Bracket To Series Door1/4 14 x 5/8 self-tapping screws Must be Adjusted ProperlyShown in FIG With StepStandard Lift Radius Being UsedTrack LOW HeadroomDIM Type of ARM Connecting Door ArmHave to cut straight arm to accomplish Trolley settingsDetermine the WAYNE-DALTON Track Radius Being Used Distance forward To Door , onLOW Headroom Trolley Positioning Chart for Door activation OperationRead and Follow ALL Instructions Operating the Wireless Wall Station Opener Controls Customizing the SettingsTeaching HomeLink to the opener Primary Programming for HomeLink to the ProdriveProgramming/Training HomeLink Unit Alternate Programming for HomeLink to the Prodrive Opening Force Adjustment AdjustmentsAdjustment # 1 Opening and Closing Force Closing Force AdjustmentWall Station Tools Needed NoneTransmitter Twice a Year MaintenanceBattery Replacement for Wall Station Symptom Probable Cause Corrective Action  TroubleshootingMAINTENANCE/ Troubleshooting # Per Unit Parts Breakdown Rail Assembly All ModelsDescription Description # Per Unit Parts Breakdown Opener Assembly And Accessories All ModelsWireless Keyless Entry Prodrive AccessoriesPre-drill 5/64 pilot hole Pre-drill 3/32 pilot holeDrill Template Thank you for your purchase Please Do Not Return This Product To The StoreReplacement labor Lifetime Limited WarrantyFCC and IC Statement Patent Information
Top Page Image Contents